When importing, we should not use Eco1 for other purposes as the
importer uses it to place unknown layer objects. We also need to avoid
placing objects on the courtyard layers that do not relate to the layer
purpose in DRC
Fixes https://gitlab.com/kicad/code/kicad/issues/9442
Also hides the net selector when in the footprint editor as it has
no meaning there. (We still only grey it out for the board editor
when the pad type has no net to keep things from coming and going too
much.)
Fixes https://gitlab.com/kicad/code/kicad/issues/9317
Allows to use Connectivity `GetConnectedTracks()` in Python.
This is in line with `GetConnectedPads()`, and with pcbnew v5.1 where
GetConnectedTracks was also usable from Python.
Fixes https://gitlab.com/kicad/code/kicad/issues/9435
1. It's impossible to use methods that modify parameters in swig so
I extend it in wrapper
2. Simplify GetArcAngle() and fix the bug where it lies about 360
degree arc to be 0 degrees.
Just wanting a SMD pad isn't enough -- the user may have already
set SMD settings into the master pad and changing the SizeX is
then very unexpected. Make sure the settings directly conflict
before making any "do what I mean" adjustments.
Also fixes the parent-footprint info when no parent exists.
Also gives a better title to the dialog when used to edit the masterPad
properties.
Fixes https://gitlab.com/kicad/code/kicad/issues/9427
Scroll-to-show on GTK relies on the idle handler but this is interrupted
by a Raise and not revisited. Since the Dialog is always on top of the
editor, Raise is not needed to view the referenced error
Fixes https://gitlab.com/kicad/code/kicad/issues/7246
We no longer have any knowledge of the original start/end of the arc,
since SetArcAngleAndEnd swaps the start and end to ensure the arc is
always clockwise at the end.
Adds a method EDA_SHAPE::EndsSwapped() to notify whether the start/end
point of the shape were swapped.
When testing for a specific layer context, we should only return true if
the item either exists on that layer or if the context layer is
UNDEFINED_LAYER, meaning the layer value is not material to the test
Relates to https://gitlab.com/kicad/code/kicad/-/issues/9366
We don't want to allow the full track width to change after placing a
segment when we are in follow-segment mode. This would require either
ripping up and re-solving the existing track or allowing potential DRC
errors.
Fixes https://gitlab.com/kicad/code/kicad/issues/9395
__WXDEBUG__ is only for internal WX debugging and is always enabled even
on release builds because it is defined to be 0, 1 or 2. Use DEBUG to
limit to debug builds
Fixes https://gitlab.com/kicad/code/kicad/issues/9392
This should not run if the action is "Cut". Additionally, we need to
transfer the expanded selection to selectionCopy in order for it to
proceed with the deletion. There is also no need for this to be limited
to the Hover action, so this section was removed.
Fixes https://gitlab.com/kicad/code/kicad/issues/9385
The rebuildLayerStackPanel() reads from the current board to setup the
panel. We maintain the board swap until after the setup is completed
Fixes https://gitlab.com/kicad/code/kicad/issues/9370
We were already checking for zone-zone overlap but missing checks when
running against (possibly) buried vias as well as the general check
Fixes https://gitlab.com/kicad/code/kicad/issues/9366
The final netclass name will be a bit long but it will allow for custom
DRC rules to individually target each of the three properties available
in CADSTAR:
- Route Code (which specifies width of the track in min, max, opt)
- Net class (only used in signal integrity analysis)
- Spacing class (for specifying clearance requirements between classes)
Seth Hillbrand
Jeff Young
Floris Lambrechts
jean-pierre charras
Wayne Stambaugh
qu1ck
Mark Hämmerling
Ian McInerney
Roberto Fernandez Bautista
Mikolaj Wielgus