3c6b98a0d5
PNS: preserve auto-detected track width when changing via sizes
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8046
2021-06-06 20:18:09 -04:00
99710aba48
PNS: use slightly less greedy algo to reset the mouse trail
2021-06-06 19:47:52 -04:00
6cb8154ec0
PNS: Remove code that broke width changes during placement
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8334
2021-06-06 19:21:52 -04:00
6789dac20b
PNS: Keep most recent good placement around for a rainy day
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8562
2021-06-06 18:56:33 -04:00
c9bc45f7ed
PNS: Limit the maximum walkaround distance factor
...
The constant chosen is somewhat arbitrary and may need
further tuning or a more complex algorithm, but in general
this will prevent churning when solutions can't be found or
a solution can be found but it is unrealistic (going around
the entire board)
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8558
2021-06-06 16:03:03 -04:00
d32b9c1c25
Use debug group for line placer debug
2021-06-06 15:44:53 -04:00
f5185f6927
Revert part of the anti-churn change, it causes bad side-effects
...
Further performance tuning could be useful but the part that
remains helps the most when hugging in large designs
2021-06-06 15:44:53 -04:00
8377ebb0e1
Fix msvc warnings
2021-06-06 15:30:31 -04:00
10e60acf34
Clean up including of board_design_settings.h
2021-06-06 15:03:42 -04:00
5349f47f95
PNS: Prevent walkaround churn in unsolvable situations
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8558
2021-06-06 14:57:52 -04:00
3475d0cebd
PNS: Grab start item based on clearance if no direct hits found
...
Fixes annoying "routing start point violates DRC" messages when
entering the router from the hotkey and not directly over a track.
2021-06-06 14:57:52 -04:00
17da050e69
Improve walkaround results when last point is inside the hull
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8563
2021-06-06 12:55:32 -04:00
be61bf29dd
Use more accurate hull shapes for round solids
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8561
2021-06-06 09:53:51 -04:00
b610b905fc
Cleanup track.h includes
2021-06-06 09:06:55 -04:00
3b7480c1c1
PNS: Invalidate start/end items after finishing a route
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8555
2021-06-06 08:52:39 -04:00
ab04e24f9a
router: rhMarkObstacles should return a correct error status
...
Long story short: a few days ago I fixed error handling in routeStep(), so it actually started to recognize the wrong error status returned
by rhMarkObstacles() and think that the trace is always incorrect.
fixes: https://gitlab.com/kicad/code/kicad/-/issues/8557
2021-06-04 23:58:56 +02:00
00791e1e37
Fix compile issues on clangd.
2021-06-03 23:41:06 +01:00
1c1ba25ffd
Use char_str instead of c_str in previous commit
2021-06-03 18:13:35 -04:00
daf510344f
Fix build error due to pns changes
2021-06-03 18:05:48 -04:00
63fc7a1908
router: support for drag/walkaround/shove for joints between lines of different widths.
...
fixes: https://gitlab.com/kicad/code/kicad/-/issues/1773
2021-06-03 22:44:53 +02:00
af26eab5fb
router: even more debug in SHOVE
2021-06-03 22:44:53 +02:00
a744857267
router: fix array out-of-bound error in HullIntersection()
...
fixes: https://gitlab.com/kicad/code/kicad/-/issues/8538
2021-06-03 22:44:53 +02:00
3e98c44636
router: LOGGER now stores UUIDs, not pointers to BOARD_ITEMs.
...
Caused occasional crashes when saving the debug event log, as some of the BOARD_ITEMS could have been deleted before SaveLog call.
2021-06-03 22:44:53 +02:00
e5e588ebba
router: temporarily export LINE::Walkaround() debug global variables
2021-06-03 22:44:53 +02:00
70ed5c1ae8
router: introduce concept of 'virtual' vias as a base for shoving/dragging joints of lines of different widths.
2021-06-03 22:44:53 +02:00
4f05262705
Cleanup includes in board.h and footprint.h
2021-06-03 20:19:52 +01:00
4df3cb912d
Remove another leaky wx/log.h header
2021-06-03 08:11:15 -04:00
cf2bb5692a
Remove the wxLog calls from math/util.h for now
...
This was leaking windows headers and partial wx headers to 1084 compilation units......
This also means math/util.h is leaking to 1084 compilation units which seems a bit high too.
2021-06-01 18:44:22 -04:00
247da631f9
Revert "Fix typo and clean up leftover tracks"
...
This reverts commit ed66c0f14d1a102f03c0https://gitlab.com/kicad/code/kicad/-/issues/8526
2021-06-01 11:18:00 -04:00
1a102f03c0
Clean up co-linear tracks after finishing routing
...
This involved adding some extra infrastructure to be able
to handle the case where a track that is sitting in the
router's commit waiting to be added to the board actually
needs to be deleted instead.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8419
2021-05-31 17:36:38 -04:00
382dca4e6f
Fix uninitialized member warnings
...
Based on PVS Studio report
2021-05-30 20:01:01 -04:00
67f0bbc6d7
router: fixed crash in HullIntersection() when the path has 0 or 1 points.
...
fixes: 8515
2021-05-31 00:20:32 +02:00
614787caae
router: clear head line geometry if current head routing failed + small improvement to follow-mouse optimization.
...
Also added a lot of verbosity for the pns-log-viewer tool.
Fixes: 8511
2021-05-31 00:18:42 +02:00
dfd80e077c
router: fix another corner case in LINE::Walkaround() (duplicated vertex triggered by feeding a closed loop as the input path)
...
fixes: 1775
2021-05-31 00:17:12 +02:00
0da85ded2f
PNS: Fix diff pair handling of microvias as start items
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8514
2021-05-30 15:51:28 -04:00
fcb89b99a3
router: walkaround algo should not copy the previous via position when the current iteration via placement fails.
...
fixes: 7827
2021-05-30 00:35:58 +02:00
af2e163890
router: annotate source locations of WALKAROUND debug items
2021-05-30 00:35:54 +02:00
3eb5a484e1
PNS: Don't clip tuning paths to pads on other layers
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8504
2021-05-29 15:52:44 -04:00
28f17c3ae6
PNS: Prevent wrong clearance being cached for new diff pairs
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8377
2021-05-29 13:31:17 -04:00
85ca85652d
Do not add debug items to view if debug flag isn't enabled
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8510
2021-05-29 12:40:24 -04:00
bd59da3642
PNS: Local min distance has a minimum points requirement
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8510
2021-05-29 12:40:24 -04:00
ebd957b08e
router: rework router's debugging infrastructure to be more compatibile with the 'qa/pns/pns-log-viewer' tool.
...
The log viewer tool lets you inspect all the intermediate stages of the routing algorithms. This patch:
- Adds source location tracking of the debug calls (need to use the PNS_DBG macro, sorry)
- Moves some wxLogTrace calls to DEBUG_DECORATOR::Message() so that messages can be displayed alongside the corresponding geometric shapes
2021-05-29 00:13:24 +02:00
132eb53a40
router: clean some debug clutter
2021-05-29 00:13:24 +02:00
b3caa3c4d4
router: fix ordering of colliding hulls in NODE::NearestObstacle()
...
Replaced the generic SHAPE_LINE_CHAIN::Intersect() with PNS::HullIntersection() which correctly rejects
'non-penetrating' intersections.
2021-05-29 00:13:24 +02:00
e66bbfd1ec
router: improve the feel of the walkaround algorithm
...
Makes walkaround more 'huggy' - the trace being routed sticks to obstacles
instead of jumping around in uncontrollable way.
2021-05-29 00:13:24 +02:00
8148b5d81f
router: improvements in LINE::Walkaround()
...
- Fix walk failure if the input path starts on the hull boundary
(happens very often during tight walkaround)
- Input line can have a loop at the end now. Such condition happens when the routing
destination point lies inside the hull of a colliding primitive.
2021-05-29 00:13:24 +02:00
d2ec3fc4ed
router: P&S-specific hull/line interection function that correctly rejects segments/vertices that only touch the hull polygons without penetrating them
2021-05-29 00:13:24 +02:00
8c4361bbc6
router: adapt to new SHAPE_LINE_CHAIN::INTERSECTIONS structure
2021-05-29 00:13:24 +02:00
5c9a73aa5e
Correct position for grid even when we're not snapping to a point.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/8125
2021-05-25 21:57:19 +01:00
4c69a74505
Force layers visible when routing on them.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/8432
2021-05-16 11:18:31 +01:00
75f49ba1b6
Add length tuner settings to toolbar context menu
2021-05-12 02:34:52 +00:00
bc6b9b527a
Allow stackup height to be excluded from length calculations
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8384
2021-05-10 22:11:58 -04:00
7356f9568d
Move grid disable modifier from ALT to CTRL.
...
Also had to move the H/V/45 disable modifier from CTRL to SHIFT.
Fixes https://gitlab.com/kicad/code/kicad/issues/8124
2021-05-09 20:17:40 +01:00
1a45d9474b
Don't show commands that cancel routing when routing is in progress
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8363
2021-05-08 14:55:02 -04:00
03cf2b517f
Enum class PAD_ATTR_T
...
Renamed such that python stays the same
2021-05-01 10:51:54 -04:00
e20562b09b
Some cleanup
2021-05-01 10:37:20 -04:00
21fde9b629
enum class PCB_SHAPE_TYPE_T
2021-04-30 22:36:12 -04:00
a433451bd8
router: 'root line' tracking in the SHOVE algorithm. See comments for detailed explanation.
2021-04-27 14:13:16 +02:00
3a8744d054
router: introduce concept of a root lines in the OPTIMIZER.
...
By 'root lines' we mean the oldest traceable ancestor of each track moved by the router
(i.e. after shoving for a while, the root of each shoved line is it's latest non-shoved version).
With this we can teach the OPTIMIZER more tricks, such as the LIMIT_CORNER_COUNT constraint. It ensures
the results of the optimization will not be less cornery than the original line, reducing the feeling
of the optimizer being too intrusive.
2021-04-27 14:13:16 +02:00
76f8861e6e
router: revert Seth's arc adjustment in StartDragging().
...
Fixes picking the last segment instead of the last vertex to drag (when one is requested).
I didn't notice any behaviour change of the dragger wrs to arcs.
2021-04-27 14:13:16 +02:00
e27733587d
Fix 2 minor Coverity warnings.
2021-04-23 19:57:36 +02:00
075bd788eb
Remove unused OBSTACLE_VISITOR::m_extraClearance
2021-04-23 01:53:09 +00:00
ecd9bf696e
Be consistent about using nullptr instead of 0
...
0 can be too easily overloaded into an int, so ensure we use nullptr
when we mean pointers.
2021-04-22 22:20:34 +01:00
cf47d665ea
PNS: Dragged line needs to retain width
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8246
2021-04-22 09:04:41 -04:00
9b1890606d
PNS: Do not allow resolved optimal values to go below board minimums
2021-04-21 22:43:26 -04:00
cbd7d698a9
Fix diff pair error message suffix suggestions
...
We accept diff pairs that end in N/P, no underscore required
2021-04-20 21:08:34 -04:00
2535daf661
PNS: Account for via stack height in diff pair length tuner
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8256
2021-04-20 19:31:10 -04:00
dd828bd964
PNS: Bring back original Highlight Collisions behavior
...
From discussion with Tom, Jeff, and Wayne, it appears as though
we all agreed that Highlight Collisions should behave like it
did in 5.1, which is to say, always just highlight collisions,
never prevent them. The Allow DRC Violations checkbox just
controls whether or not you can fix/commit the head line if it
has violations; you are not prevented from moving the head
line to violating positions in any case.
Right now, there does not seem to be much demand for a separate
"Stop at First Obstacle" mode since Walkaround basically does that
but better, but we agreed that if there is demand for it in the
future, it should be implemented as a new router mode rather than
a behavior of Highlight Collisions mode controlled by the Allow
DRC Violations checkbox.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7828
2021-04-18 21:01:07 -04:00
4538d78828
router: fix via shoving regression.
2021-04-19 00:43:30 +02:00
57de83897a
router: VIA SetDrill() and SetPosition() must update the hole shape too.
2021-04-19 00:43:15 +02:00
ec6995697d
PNS: even more free performance
...
If this doesn't work, we have bigger problems
2021-04-18 09:50:06 -04:00
6425ad4118
PNS: Fix propagateDpHeadForces obstacle calculation
...
Using a synthetic via here doesn't quite let us use VIA::PushoutForce
because it will use the wrong clearance, and also doesn't quite have
the logic we want. I am not familiar enough with PushoutForce to know
if its logic is a bug in other cases, so instead I just brought in the
parts of its algorithm that are needed here.
Additionally, we prevent pushing more than once from a given obstacle,
which causes walkaround to be more successful when routing diff pairs
against a large collider such as a keepout area.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8232
2021-04-17 22:37:30 -04:00
5974446523
PNS: Let's make the r-tree work for us
...
I'm not sure where the magic number of "4x worst" came from, but it's
been around forever. This is extremely inefficient as it negates much
of the power of r-tree filtering in dense designs. If we really trusted
it, we could set this just to worstClearance. Keeping it above the worst
clearance by a little bit seems to provide enough of a speed improvement
to resolve the test cases I have, so I'll go with that for now.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7777
2021-04-17 21:37:11 -04:00
1d7e5a0443
Fix merge error that prevented a previous change from working
2021-04-14 23:30:16 -04:00
268d570941
PNS: keep last valid diff pair trace as current state
...
This allows fixing/committing what is on screen even if the current
cursor position doesn't have a valid solution (the old behavior
would result in the current trace disappearing)
2021-04-14 23:21:10 -04:00
c829dba88e
PNS: Reduce minimum distance to start turn in diff pair placer
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8193
2021-04-14 23:21:10 -04:00
cac4d70154
PNS: Respect fix-all in diff pair placer
2021-04-14 23:21:10 -04:00
296a9df530
PNS: Pick up diff pair starting width from continuation track
2021-04-12 23:10:15 -04:00
1d9ca181a2
PNS: Use existing seg direction if both DP segs are parallel
2021-04-12 22:34:13 -04:00
311cde0984
Safety check suggested by Coverity
2021-04-12 20:42:50 -04:00
2aa5e568e8
Refactoring
2021-04-12 20:40:05 -04:00
73fb85a352
PNS: Calculate diff pair primitive orientation using anchors only
...
The previous method fails if the primitive is an expanding or
contracting pair (diagonals going inward or outward) resulting in
incorrect orientation, which then leads to incorrect candidate
gateways being generated and no solution found.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8185
2021-04-12 20:34:44 -04:00
715c61ac9f
PNS: Fix yet more arc edge cases
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8150
2021-04-12 19:59:55 -04:00
49a91414d7
PNS: Apply co-linear seg merging to drag operations
2021-04-11 22:32:11 -04:00
1c431d9929
PNS: Fix some off-by-one errors with arc dragging
2021-04-11 22:12:53 -04:00
a26fc6d65d
PNS: Fix several issues with arc dragging
...
Do not merge vertices that belong to different arcs
Fix start segment identification after arcs
Fix free-angle drag after arc
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8173
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8150
2021-04-11 17:56:40 -04:00
7ba110bd77
PNS: Fix dragging of segments with arcs in line
2021-04-11 10:18:57 -04:00
a30894e5a1
Allow SHAPE_LINE_CHAIN and SHAPE_ARC to be mirrored using a SEG
2021-04-11 13:27:25 +00:00
fe8fbf1d5d
Use arcs instead of line approximation for Miter shape
...
TODO:
* The resulting line chain is broken with the arcs, and
this appears to be some subsequent issue I was not able to pin down.
* The requirement of a correction factor is not clear to me
2021-04-11 13:27:25 +00:00
5c448057c8
PNS: Prevent state flicker when starting drag
2021-04-10 16:31:39 -04:00
7784d7cb12
PNS: Fix visible area restriction
...
VIEW::GetBoundary() returns the entire view area, not the visible area.
Surprisingly, we had no API for this, so I added one.
Also, changed the dragger behavior to toggle between optimizing just the
modified area and optimizing the visible area, i.e. we will now never
optimize off-screen portions of the dragged track.
2021-04-10 16:13:08 -04:00
94afdcb92a
PNS: Allow control of area-restricted drag optimization
...
CHANGED: The interactive router settings now include a switch to
enable or disable optimization of the entire dragged track,
which is now disabled by default. When enabled, the router
will reroute the entire track (from the dragged segment to
the closest pad/via in each direction) to be more optimal.
When disabled, only the area around the dragged segment
will be modified.
CHANGED: The "optimizer effort" slider is removed from the interactive
router settings dialog, as this setting did not have any
meaningful impact in most cases and was a source of confusion.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/5918
2021-04-10 15:17:39 -04:00
dc0cf3b802
Clean up a confusing API.
...
AllowDRCViolations is kept in any mode as a *setting*, but only
controls router behaviour when the mode is mark obstacles.
Fixes https://gitlab.com/kicad/code/kicad/issues/7795
2021-04-10 11:08:02 +01:00
d878cbddbc
PNS: a few forgotten cleanup items
2021-04-07 23:34:45 -04:00
c9040a5c53
PNS: fix some weirdness identified by PVS
2021-04-07 23:16:56 -04:00
d4957b112e
PNS: Keep last valid drag solution in the node
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/5450
2021-04-07 21:59:23 -04:00
26835f582c
Some situations require more than one dummy
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7820
2021-04-07 21:30:18 -04:00
9432484394
PNS: Find origin segment correctly when arcs are present
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8139
2021-04-07 20:28:30 -04:00
9f957d3e08
Fix crash when attempting to tune discontinuous lines
...
Also correctly find the tuning path through arcs
https://gitlab.com/kicad/code/kicad/-/issues/8131
2021-04-06 09:07:11 -04:00
b2f788adc1
PNS: Fix UseConnectedTrackWidth when starting from ARCs
2021-04-06 01:27:13 +00:00
e46c9d35ac
Add undo/redo handling to length tuner event loop
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8129
2021-04-05 19:58:14 -04:00
24cd174a23
Don't dereference a possibly-invalid optional
2021-04-05 19:34:57 -04:00
a6c3d74a73
Pass active layer to StartRouting in length tuner
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7857
2021-04-04 21:51:54 -04:00
a24bc34b66
Better colors for length tuning popup in dark mode
2021-04-04 20:33:59 -04:00
c7ecb51f77
Update PNS length tuning algorithm to match the new BOARD algorithm
...
Now tracks inside pads are optimized to give a more accurate length.
Also, the start/end of the assembled line is used to identify the right
pad joints for pad-to-die length calculation.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/4204
Fixes https://gitlab.com/kicad/code/kicad/-/issues/1765
Fixes https://gitlab.com/kicad/code/kicad/-/issues/6877
2021-04-04 20:27:22 -04:00
cdfb014ab6
CHANGED: Account for via height in track length calculations
2021-04-04 13:59:18 -04:00
6b24abac8f
PNS: Don't snap to end items if snapping is disabled by modifier key
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8033
2021-04-04 10:22:23 -04:00
a8896ebd73
Don't show leading ratline for unconnected net
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8040
2021-04-02 20:29:25 -04:00
f88d39b4f0
Fix state issue in router's switch layer handling.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7590
2021-04-01 18:10:04 +01:00
8cb6f15687
Warn when diff pair router can't start due to too-small-gap.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7795
2021-03-30 19:49:23 +01:00
78a60e9dfb
PNS: Put polygon error outside pad shapes
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7672
2021-03-29 19:49:59 -04:00
6cbc3fb97d
Fix a minor inconsistency between router and DRC
...
Also make sure collision highlighting runs at the starting
location of a drag.
See: https://gitlab.com/kicad/code/kicad/-/issues/7672
2021-03-29 19:41:17 -04:00
8be9832153
PNS: Don't highlight Net 0 (the unconnected net)
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8040
2021-03-29 17:45:07 -04:00
132ec37b56
Handle arc in buildHullForPrimitiveShape
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/8008
2021-03-25 21:25:30 -04:00
8be213e36f
Trim includes (and use consistent terminology in error messages).
2021-03-21 20:15:47 +00:00
5e0b65c3a8
Change wording of corner rounding action
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/4505
2021-03-21 15:55:56 -04:00
cad1cb0262
Improve naming.
2021-03-16 12:07:06 +00:00
18037e2f65
Rework bitmap system to load from archived PNGs
...
Bitmaps are now identified by an enum class instead of by pointers.
Bitmap loading and caching is now handled by a class in common, and
we no longer compile most bitmaps into the binary, so there is no
longer a bitmaps static library.
Instead, bitmaps are archived to a .tar.gz file which is installed
in ${KICAD_DATA}/resources/images.tar.gz
The source PNGs are checked in to Git as the original CPP files were,
so that people can build without the required dependencies to convert
SVGs to PNGs.
Initial support is also added for dark theme icons, although this
is not yet exposed in the GUI.
Stubs are present for multi-resolution image resources, but this is
not fully-baked yet and could use some refinement.
2021-03-11 08:37:35 -05:00
720147d272
Remove transitive inclusion of bitmaps.h
2021-03-07 16:08:57 -05:00
df99ee39d9
PNS: new through vias should span all copper layers
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7576
2021-03-07 17:58:43 +00:00
79a9d69ff5
Coverity fixes for issues 314755, 316287, 324536, 324539, and 324539.
2021-03-02 08:10:37 -05:00
d06e8ef01c
Honour pre-defined-size selections for diff pairs.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7759
2021-03-02 12:12:05 +00:00
d269778cd4
PNS: disable smart pads in walkaround if posture is forced
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7710
2021-02-27 13:48:01 -05:00
b36e1c741d
Fix insidious bug which resets layer of SOLID when marking collision.
...
It's supposed to be setting the layer of the collsion display object,
not the host object, but there's a typo.
Fixes https://gitlab.com/kicad/code/kicad/issues/7712
2021-02-25 23:39:48 +00:00
75032f3acd
Use the more-constrained layer when running rules.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7639
2021-02-25 22:58:07 +00:00
87ea540953
Fix whitespace errors
2021-02-25 17:18:23 +01:00
c79610e132
router: post-rebase fixes
2021-02-25 17:18:23 +01:00
6948cdd8ef
router: Fix return type within pointInside2
2021-02-25 17:18:23 +01:00
9bdfc13155
router: improve locality of post-shove optimization
...
Fixes : #4359
2021-02-25 17:18:23 +01:00
e1d4bb777c
router: use new LINE::Walkaround in the walkaround algo
2021-02-25 17:18:23 +01:00
045d02f818
router: add strict/loose area restriction constraint. WIP
2021-02-25 17:18:23 +01:00
24574aa2f5
router: first insert intersections, then build graph in Walkaround()
2021-02-25 17:18:23 +01:00
61e75a838b
router: replace large stack variables with std::array
2021-02-25 17:18:23 +01:00
028f209126
router: more robust LINE::Walkaround() implementation
2021-02-25 17:18:23 +01:00
e9c55cd0e3
router: if the drag anchor is not reachable by the mouse, use the closest point on dragged trace for optimizer restriction
...
Fixes : #4056
2021-02-25 17:18:23 +01:00
a141ed3444
router: feed view size change events to the router engine
2021-02-25 17:18:23 +01:00
12dfb541fc
router: expose current view area to the router algorithms so that the optimizer could know not to mess with traces/vias not currently visible to the user (wip)
2021-02-25 17:18:23 +01:00
2831c7d24c
router: fix compile error in DRAGGER
2021-02-25 17:18:23 +01:00
b67e5768a6
router: feature to save debug event log & board dump for easier recreation of router bugs and misbehaviours
2021-02-25 17:18:23 +01:00
ebdc68ac1d
router: correctly handle line width in PREVIEW_ITEMs
2021-02-25 17:18:23 +01:00
34c037684b
router: partially migrate SHOVE algorithm to use new DEBUG_DECORATOR
2021-02-25 17:18:23 +01:00
0e6cf3f56e
router: fix board edge clearance queries
...
Fixes : #7254
2021-02-25 17:18:23 +01:00
4574f52eac
router: DRAGGER::CurrentNode() should always return non-null value
2021-02-25 17:18:23 +01:00
e221b11e3b
GRID_HELPER: fixed arithmetic issue in segment snap distance check disguised as 'excessive optimization' by the dragger in the router
2021-02-25 17:18:23 +01:00
325300bd76
router: don't use compound pad shapes if pad contains a single primitive shape
2021-02-25 17:18:23 +01:00
a4bd2ad8c6
router: drag in walkaround mode now works
2021-02-25 17:18:23 +01:00
f84836f51e
router: factor out POSTURE_SOLVER to more generic MOUSE_TRAIL_TRACER class
2021-02-25 17:18:23 +01:00
af95235f47
router: report debug log events from DRAGGER
2021-02-25 17:18:23 +01:00
0306d16748
router: make post-drag optimization less intrusive
...
Fixes : #5918
2021-02-25 17:18:23 +01:00
14ce7a0ad7
router: implement area constraint in optimizer
2021-02-25 17:18:23 +01:00
64cf593ee9
router: debug points now have variable size
2021-02-25 17:18:23 +01:00
caa18c8e16
Fix bugs in diffPair hole-to-hole logic and add rule resolution.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7697
2021-02-25 14:23:02 +00:00
fa89263c8f
Push hole-to-hole min processing down a level.
...
Also removes adding the track width to the via gap, which was
never right.
Fixes https://gitlab.com/kicad/code/kicad/issues/7173
2021-02-24 21:42:00 +00:00
7f892669cc
Consistent punctuation.
2021-02-23 12:46:27 +00:00
c12666ec43
Fix arg type of NODE::followLine
2021-02-20 11:58:55 -05:00
6fce39607e
Fix return type within pointInside2
2021-02-20 11:58:55 -05:00
d0b91b1106
Router, place via: fix issue created by 45b2bc: cancelling via must be made
...
only when the select layer is called.
Fixes #7606
https://gitlab.com/kicad/code/kicad/issues/7606
2021-02-19 17:28:20 +01:00
54282dffe3
Move preview items using FP orientation
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7600
2021-02-18 16:32:40 -08:00
45b2bce698
Cancel placement of via if user cancels layer selection.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7578
2021-02-18 11:53:36 +00:00
5d2dc0b50e
Fix a few (minor) issues:
...
- Make DIALOG_SHIM::SetPosition working)
- rename PCB_BASE_FRAME::SelectLayer() to PCB_BASE_FRAME::SelectOneLayer()
- PCB_BASE_FRAME::SelectOneLayer(): make dismiss dialog by escape key working.
Fixes #7578
https://gitlab.com/kicad/code/kicad/issues/7578
2021-02-17 20:56:43 +01:00
0198d5a3bd
PNS: don't lose track of pad offset when dragging footprints
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7500
2021-02-16 19:47:52 -05:00
9212197c26
Grammar
2021-02-15 15:18:13 -08:00
e2f8b1a4b1
Interpreting wxDialog::ShowModal()'s retval as bool is never what you want.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/7454
2021-02-08 17:40:57 +00:00
6272b48481
Make sure layer gets passed in to rules evaluation.
2021-02-08 14:53:49 +00:00
7aa7e3fd43
Push undo/redo blocking down a level in LengthTuner tool.
...
This way it's active only while tuning a single line, rather than
while the tool is selected.
Fixes https://gitlab.com/kicad/code/kicad/issues/7462
2021-02-08 14:15:46 +00:00
792904557e
Remember Parent data when routing
...
Keeps parent information such as UUID and pad removal options for
elements that are just updated in routing rather than created fresh or
fully destroyed.
Fixes https://gitlab.com/kicad/code/kicad/issues/7460
2021-02-07 17:08:43 -08:00
721bf82603
Handle malformed lines in dragCornerInternal
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7398
2021-02-03 20:55:22 -05:00
d7ddc62d7e
Fix mouse warping and dialog placement for layer switcher.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/2607
2021-02-02 17:20:01 +00:00
dc4b73fcef
Correct m_board check location in PNS_KICAD_IFACE_BASE::SyncWorld
2021-02-01 11:58:22 -05:00
73886aecb1
Ensure partially triangulated polys are not valid
...
Moves rule area triangulation outside of layer iterator and keeps the
triangulation_valid flag false until the triangulation has been
completed.
Fixes https://gitlab.com/kicad/code/kicad/issues/7032
2021-01-29 16:33:57 -08:00
6a39b81647
Fix the last of broken Doxygen comment specifiers.
2021-01-27 17:39:44 -05:00
3e42ba18a9
Show dragging tools in context selection menu for components
...
Show the dragging tools in the context selection menu when a single
component is selected. Prevent the dragging tools from appearing when
more than one object is selected, as they will not activate anyway.
Fixes https://gitlab.com/kicad/code/kicad/issues/7258
2021-01-27 19:55:42 +00:00
b96bcc86b1
Don't restrict start item to same layer if snapping is enabled
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/7276
2021-01-25 21:19:26 -05:00
3fcd0860c1
Make 'E' go straight to Custom Track Width dialog.
...
Also fixes some mouse capture issues.
Fixes https://gitlab.com/kicad/code/kicad/issues/7198
2021-01-20 18:19:55 +00:00
330d717c69
Fix typo
2021-01-18 21:50:26 -05:00
44655b98de
Initialize variables properly
2021-01-18 18:35:10 +00:00
68efdb2fff
Push shared parts of GRID_HELPERs into common.
2021-01-16 23:18:10 +00:00
02ccd5fbdb
Make sure properties commands don't go to other tools during routing.
...
Brings up the track widths (or diff pairs) context menu instead,
which seems to be the closest parallel.
Fixes https://gitlab.com/kicad/code/kicad/issues/7099
2021-01-14 15:19:09 +00:00
dc02ec9758
Remove a few const_cast
2021-01-12 20:51:31 +00:00
111fa99f9f
PNS: Use last-segment posture optimization always
...
Also when auto-posture is enabled, don't flutter
until area threshold has been met.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/6935
2021-01-07 20:12:31 -05:00
6ca9a42251
Removes 3 other instances of a potential encoding problem
...
Signed-off-by: hoijui <hoijui.quaero@gmail.com>
2021-01-07 17:36:49 +00:00
e41c06304b
Don't show a leading ratline to a NPTH.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/6960
2021-01-07 12:25:04 +00:00
f702b64b8d
Minor improvements to formatting & SNR.
2021-01-07 12:25:04 +00:00
0234b7278a
PNS: Make DIRECTION_45 North be up everywhere
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/6935
2021-01-06 21:47:06 -05:00
46c4727783
Make MSVC happy again
2021-01-05 20:56:37 -05:00
e7b047660c
PNS: Correctly assemble lines with reversed arcs
2021-01-05 17:57:21 -05:00
feda03f69b
PNS: Fix arc orientation when assembling lines with backwards arcs
2021-01-05 17:57:21 -05:00
7431d5c985
PNS: First pass at updating meander placers for arcs
...
Fixes https://gitlab.com/kicad/code/kicad/-/issues/6464
2021-01-05 17:57:21 -05:00
8619086cf2
PNS: re-enable optimization of colinear segs in lines with arcs
2021-01-05 17:57:21 -05:00
8901e71fc8
PNS: Fix loop removal, make walkaround less broken for arcs
2021-01-05 17:57:21 -05:00
02cd8c99cd
Better error messages when routing can't be started.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/6541
2021-01-05 18:47:58 +00:00
88d42724e6
Remove diff-pair-gap handling from single-line-router.
...
We can't really support it until we do min/max/opt shoving and
dragging.
Fixes https://gitlab.com/kicad/code/kicad/issues/6932
2021-01-05 16:54:52 +00:00
d975f2f6aa
Commenting and naming for clarity.
2021-01-05 16:54:52 +00:00
f7b20611c1
Enforce hole-to-hole min when placing diffpair vias.
...
Fixes https://gitlab.com/kicad/code/kicad/issues/6931
2021-01-05 00:26:49 +00:00
93bd2171ab
Formatting.
2021-01-05 00:26:49 +00:00
d24b034cbc
Cleanup (and a minor performance improvement).
2021-01-04 22:32:29 +00:00
2ea6bc5529
Formatting.
2021-01-04 19:19:55 +00:00
648c42f643
Show collisions preventing routing from starting.
...
Also introduces a callback to the infobar so that the view can be
cleaned up when the timer expires.
Fixes https://gitlab.com/kicad/code/kicad/issues/6930
2021-01-04 19:19:55 +00:00
71215bcab3
Make sure TH pads get collision layer highlighted.
...
Also cleans it up to centralise all the decision-making.
Fixes https://gitlab.com/kicad/code/kicad/issues/6925
2021-01-03 21:16:09 +00:00
f01297fedd
Convert an annoying message box to an infobar
2021-01-02 22:14:10 -05:00
Jon Evans
Marek Roszko
Tomasz Wlostowski
Jeff Young
Ian McInerney
david-beinder
jean-pierre charras
Jonathan Haas
Thomas Pointhuber
Wayne Stambaugh
Seth Hillbrand
Mikołaj Wielgus
Dominik Wernberger
hoijui