72 lines
3.1 KiB
HTML
72 lines
3.1 KiB
HTML
<html>
|
|
<!-- This file is used to autogenerate a *.h file, but you can load it into a browser to preview -->
|
|
<h1>Freerouter Guidelines:</h1>
|
|
<ol>
|
|
<li> in pcbnew, using the Layers Setup dialog:</li><br>
|
|
<li>choose the number of layers, and enter the name of each layer.</li><br>
|
|
These should look something like this:
|
|
<ul>
|
|
<li>Layer[0] Back signal</li>
|
|
<li>Layer[1] Power power</li>
|
|
<li>Layer[2] V2_Signal signal</li>
|
|
<li>Layer[3] H1_Signal signal</li>
|
|
<li>Layer[4] Ground power</li>
|
|
<li>Layer[15] Front signal</li>
|
|
</ul><br>
|
|
Notice that after the layer name there is a layer type field, either 'signal' or 'power'.<br>
|
|
Any layer identified as 'power' will be removed from the layer menu in Freerouter,
|
|
as this will be assumed to contain a power zone.
|
|
</li><br><br>
|
|
|
|
<li> in pcbnew: establish board perimeter.</li><br>
|
|
|
|
<li> in pcbnew: load in the netlist so you have all the components defined and instantiated.</li><br>
|
|
|
|
<li> in pcbnew: establish any zones, inclusive of net association.</li><br>
|
|
|
|
<li> in pcbnew: do the degree of component placements you are comfortable with.
|
|
It is a little easier to accurately position components in pcbnew than in
|
|
freerouter, but either will work.</li><br>
|
|
|
|
<li> in pcbnew: set up the netclasses. Power traces might be a little thicker
|
|
than signal traces. If so, add a netclass called 'power'.
|
|
Make its traces thicker than what you establish for netclass 'Default'.
|
|
Set trace width, spacing and vias for each netclass.</li><br>
|
|
|
|
<li> in pcbnew: export to DSN.</li><br>
|
|
|
|
<li> load up freerouter (keep it running for any subsequent iterations of 5) through 16) here).</li><br>
|
|
|
|
<li> in freerouter: load the project's *.dsn file. Immediately after a load, all
|
|
components and traces (if any) will initially be 'fixed'. This is a 'lock
|
|
in place' toggle that you can undo by selecting a region with your mouse
|
|
and then selecting 'Unfix' from the menu. Occassionally you may want to
|
|
re-fix a trace or a part, if only temporarily. This keeps it locked in
|
|
place.
|
|
</li><br>
|
|
|
|
<li> useful, not mandatory: in freerouter: set your move snap modulus, which seems
|
|
to default to 1 internal unit.
|
|
20 mils in x and in y is about reasonable.</li><br>
|
|
|
|
<li> in freerouter: finish placing any components, you can change sides of a part
|
|
here also, rotate, whatever.</li><br>
|
|
|
|
<li> in freerouter: route the board, and save frequently to a *.dsn file while
|
|
routing in case of power loss. Pick the menu option for saving a full *.dsn
|
|
file, not a session file (yet). The full freerouter *.dsn file is a superset
|
|
format, one that can be reloaded in the event of a power loss. Whereas the
|
|
*.ses file is not a complete design, but only with the *.brd file
|
|
constitutes a full design. So it is important to backup your work to a
|
|
*.dsn file while routing in case of power loss.</li><br>
|
|
|
|
<li> in freerouter: when done, or when you want to back import, then save as a session file, *.ses.</li><br>
|
|
|
|
<li> in pcbnew: backimport the session file</li><br>
|
|
|
|
<li> in pcbnew: at this point the zones have to be refilled. One way to do that
|
|
is to simply run DRC.</li>
|
|
|
|
</ol>
|
|
</html>
|