diff --git a/DAP_config.h b/bsp/default/DAP_config.h similarity index 95% rename from DAP_config.h rename to bsp/default/DAP_config.h index d72afc4..380e914 100644 --- a/DAP_config.h +++ b/bsp/default/DAP_config.h @@ -1,3 +1,7 @@ +/* +This is *NOT* a valid CMSIS-DAP configuration; it is merely a fallback default to compile. +*/ + /* * Copyright (c) 2013-2017 ARM Limited. All rights reserved. * @@ -49,7 +53,7 @@ This information includes: /// Processor Clock of the Cortex-M MCU used in the Debug Unit. /// This value is used to calculate the SWD/JTAG clock speed. -#define CPU_CLOCK 48000000U ///< Specifies the CPU Clock in Hz. +#define CPU_CLOCK 100000000U ///< Specifies the CPU Clock in Hz. /// Number of processor cycles for I/O Port write operations. /// This value is used to calculate the SWD/JTAG clock speed that is generated with I/O @@ -65,7 +69,7 @@ This information includes: /// Indicate that JTAG communication mode is available at the Debug Port. /// This information is returned by the command \ref DAP_Info as part of Capabilities. -#define DAP_JTAG 0 ///< JTAG Mode: 1 = available, 0 = not available. +#define DAP_JTAG 1 ///< JTAG Mode: 1 = available, 0 = not available. /// Configure maximum number of JTAG devices on the scan chain connected to the Debug Access Port. /// This setting impacts the RAM requirements of the Debug Unit. Valid range is 1 .. 255. @@ -188,148 +192,6 @@ of the same I/O port. The following SWDIO I/O Pin functions are provided: - \ref PIN_SWDIO_OUT to write to the SWDIO I/O pin with utmost possible speed. */ -#include "swdio_bsp.h" - -// SWCLK/TCK I/O pin ------------------------------------- - -/** SWCLK/TCK I/O pin: Get Input. -\return Current status of the SWCLK/TCK DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN (void) { - return (CLK_READ) ? 1 : 0; -} - -/** SWCLK/TCK I/O pin: Set Output to High. -Set the SWCLK/TCK DAP hardware I/O pin to high level. -*/ -__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET (void) { - CLK_HIGH; -} - -/** SWCLK/TCK I/O pin: Set Output to Low. -Set the SWCLK/TCK DAP hardware I/O pin to low level. -*/ -__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR (void) { - CLK_LOW; -} - - -// SWDIO/TMS Pin I/O -------------------------------------- - -/** SWDIO/TMS I/O pin: Get Input. -\return Current status of the SWDIO/TMS DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN (void) { - return (DATA_READ) ? 1 : 0; -} - -/** SWDIO/TMS I/O pin: Set Output to High. -Set the SWDIO/TMS DAP hardware I/O pin to high level. -*/ -__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET (void) { - DATA_HIGH; -} - -/** SWDIO/TMS I/O pin: Set Output to Low. -Set the SWDIO/TMS DAP hardware I/O pin to low level. -*/ -__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR (void) { - DATA_LOW; -} - -/** SWDIO I/O pin: Get Input (used in SWD mode only). -\return Current status of the SWDIO DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN (void) { - return (DATA_READ) ? 1 : 0; -} - -/** SWDIO I/O pin: Set Output (used in SWD mode only). -\param bit Output value for the SWDIO DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE void PIN_SWDIO_OUT (uint32_t bit) { - if (bit & 1) { DATA_HIGH; } else { DATA_LOW; } -} - -/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only). -Configure the SWDIO DAP hardware I/O pin to output mode. This function is -called prior \ref PIN_SWDIO_OUT function calls. -*/ -__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE (void) { - DATA_ENABLE; -} - -/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only). -Configure the SWDIO DAP hardware I/O pin to input mode. This function is -called prior \ref PIN_SWDIO_IN function calls. -*/ -__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE (void) { - DATA_HIZ; -} - - -// TDI Pin I/O --------------------------------------------- - -/** TDI I/O pin: Get Input. -\return Current status of the TDI DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_TDI_IN (void) { - return (0U); -} - -/** TDI I/O pin: Set Output. -\param bit Output value for the TDI DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE void PIN_TDI_OUT (uint32_t bit) { - ; -} - - -// TDO Pin I/O --------------------------------------------- - -/** TDO I/O pin: Get Input. -\return Current status of the TDO DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_TDO_IN (void) { - return (0U); -} - - -// nTRST Pin I/O ------------------------------------------- - -/** nTRST I/O pin: Get Input. -\return Current status of the nTRST DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN (void) { - return (0U); -} - -/** nTRST I/O pin: Set Output. -\param bit JTAG TRST Test Reset pin status: - - 0: issue a JTAG TRST Test Reset. - - 1: release JTAG TRST Test Reset. -*/ -__STATIC_FORCEINLINE void PIN_nTRST_OUT (uint32_t bit) { - ; -} - -// nRESET Pin I/O------------------------------------------ - -/** nRESET I/O pin: Get Input. -\return Current status of the nRESET DAP hardware I/O pin. -*/ -__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN (void) { - return (RESET_READ) ? 1 : 0; -} - -/** nRESET I/O pin: Set Output. -\param bit target device hardware reset pin status: - - 0: issue a device hardware reset. - - 1: release device hardware reset. -*/ -__STATIC_FORCEINLINE void PIN_nRESET_OUT (uint32_t bit) { - if (bit & 1) { RESET_HIGH; } else { RESET_LOW; } -} // Configure DAP I/O pins ------------------------------ @@ -348,10 +210,7 @@ Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode: - TDI, nTRST to HighZ mode (pins are unused in SWD mode). */ __STATIC_INLINE void PORT_SWD_SETUP (void) { - SWDIO_INIT; - CLK_HIGH; CLK_ENABLE; - DATA_HIGH; DATA_ENABLE; - RESET_HIGH; RESET_ENABLE; + ; } /** Disable JTAG/SWD I/O Pins. @@ -359,9 +218,149 @@ Disables the DAP Hardware I/O pins which configures: - TCK/SWCLK, TMS/SWDIO, TDI, TDO, nTRST, nRESET to High-Z mode. */ __STATIC_INLINE void PORT_OFF (void) { - CLK_HIZ; - DATA_HIZ; - RESET_HIZ; + ; +} + + +// SWCLK/TCK I/O pin ------------------------------------- + +/** SWCLK/TCK I/O pin: Get Input. +\return Current status of the SWCLK/TCK DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN (void) { + return (0U); +} + +/** SWCLK/TCK I/O pin: Set Output to High. +Set the SWCLK/TCK DAP hardware I/O pin to high level. +*/ +__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET (void) { + ; +} + +/** SWCLK/TCK I/O pin: Set Output to Low. +Set the SWCLK/TCK DAP hardware I/O pin to low level. +*/ +__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR (void) { + ; +} + + +// SWDIO/TMS Pin I/O -------------------------------------- + +/** SWDIO/TMS I/O pin: Get Input. +\return Current status of the SWDIO/TMS DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN (void) { + return (0U); +} + +/** SWDIO/TMS I/O pin: Set Output to High. +Set the SWDIO/TMS DAP hardware I/O pin to high level. +*/ +__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET (void) { + ; +} + +/** SWDIO/TMS I/O pin: Set Output to Low. +Set the SWDIO/TMS DAP hardware I/O pin to low level. +*/ +__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR (void) { + ; +} + +/** SWDIO I/O pin: Get Input (used in SWD mode only). +\return Current status of the SWDIO DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN (void) { + return (board_millis() & 1); /* pacify GCC warning */ +} + +/** SWDIO I/O pin: Set Output (used in SWD mode only). +\param bit Output value for the SWDIO DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE void PIN_SWDIO_OUT (uint32_t bit) { + (void)bit; +} + +/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only). +Configure the SWDIO DAP hardware I/O pin to output mode. This function is +called prior \ref PIN_SWDIO_OUT function calls. +*/ +__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE (void) { + ; +} + +/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only). +Configure the SWDIO DAP hardware I/O pin to input mode. This function is +called prior \ref PIN_SWDIO_IN function calls. +*/ +__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE (void) { + ; +} + + +// TDI Pin I/O --------------------------------------------- + +/** TDI I/O pin: Get Input. +\return Current status of the TDI DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_TDI_IN (void) { + return (0U); +} + +/** TDI I/O pin: Set Output. +\param bit Output value for the TDI DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE void PIN_TDI_OUT (uint32_t bit) { + (void)bit; +} + + +// TDO Pin I/O --------------------------------------------- + +/** TDO I/O pin: Get Input. +\return Current status of the TDO DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_TDO_IN (void) { + return (board_millis() & 1); /* pacify GCC warning */ +} + + +// nTRST Pin I/O ------------------------------------------- + +/** nTRST I/O pin: Get Input. +\return Current status of the nTRST DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN (void) { + return (0U); +} + +/** nTRST I/O pin: Set Output. +\param bit JTAG TRST Test Reset pin status: + - 0: issue a JTAG TRST Test Reset. + - 1: release JTAG TRST Test Reset. +*/ +__STATIC_FORCEINLINE void PIN_nTRST_OUT (uint32_t bit) { + (void)bit; +} + +// nRESET Pin I/O------------------------------------------ + +/** nRESET I/O pin: Get Input. +\return Current status of the nRESET DAP hardware I/O pin. +*/ +__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN (void) { + return (0U); +} + +/** nRESET I/O pin: Set Output. +\param bit target device hardware reset pin status: + - 0: issue a device hardware reset. + - 1: release device hardware reset. +*/ +__STATIC_FORCEINLINE void PIN_nRESET_OUT (uint32_t bit) { + (void)bit; } ///@} @@ -385,14 +384,18 @@ It is recommended to provide the following LEDs for status indication: - 1: Connect LED ON: debugger is connected to CMSIS-DAP Debug Unit. - 0: Connect LED OFF: debugger is not connected to CMSIS-DAP Debug Unit. */ -__STATIC_INLINE void LED_CONNECTED_OUT (uint32_t bit) {} +__STATIC_INLINE void LED_CONNECTED_OUT (uint32_t bit) { + (void)bit; +} /** Debug Unit: Set status Target Running LED. \param bit status of the Target Running LED. - 1: Target Running LED ON: program execution in target started. - 0: Target Running LED OFF: program execution in target stopped. */ -__STATIC_INLINE void LED_RUNNING_OUT (uint32_t bit) {} +__STATIC_INLINE void LED_RUNNING_OUT (uint32_t bit) { + (void)bit; +} ///@} diff --git a/bsp/default/swdio_bsp.h b/bsp/default/swdio_bsp.h deleted file mode 100644 index 35fa22d..0000000 --- a/bsp/default/swdio_bsp.h +++ /dev/null @@ -1,27 +0,0 @@ -#ifndef __SWDIO_BSP_H -#define __SWDIO_BSP_H - -#warning "code will not function as-is; swdio_bsp.h must be created to suit the target hardware" - -#define CLK_LOW { } -#define CLK_HIGH { } -#define CLK_ENABLE { } -#define CLK_HIZ { } - -#define DATA_LOW { } -#define DATA_HIGH { } -#define DATA_ENABLE { } -#define DATA_HIZ { } - -#define RESET_LOW { } -#define RESET_HIGH { } -#define RESET_ENABLE { } -#define RESET_HIZ { } - -#define SWDIO_INIT { } - -#define DATA_READ (0) -#define CLK_READ (0) -#define RESET_READ (0) - -#endif /* __SWDIO_BSP_H */ diff --git a/main.c b/main.c index d5b3ca2..b3af133 100644 --- a/main.c +++ b/main.c @@ -68,7 +68,7 @@ uint16_t tud_hid_get_report_cb(uint8_t report_id, hid_report_type_t report_type, void tud_hid_set_report_cb(uint8_t report_id, hid_report_type_t report_type, uint8_t const* RxDataBuffer, uint16_t bufsize) { - uint8_t TxDataBuffer[CFG_TUD_HID_EP_BUFSIZE]; + static uint8_t TxDataBuffer[CFG_TUD_HID_EP_BUFSIZE]; uint32_t response_size = TU_MIN(CFG_TUD_HID_EP_BUFSIZE, bufsize); // This doesn't use multiple report and report ID