* Make the grid display settings separate from the board object
* Ensure that the grid is initialized on creation in all the frames
Fixes: lp:1843169
* https://bugs.launchpad.net/kicad/+bug/1843169
Mainly because it creates a new keyword a new keyword in *.kicad_pcb files,
and needs some tests, this is currently a advanced feature.
Enable it by adding "UsePinFunction=1" in "kicad_advanced" config file.
Note also "UsePinFunction=1" only enable saving this info in *.kicad_pcb
and kicad_mod files.
The pin name defined in Eeschema is now available as pad info.
Useful for the board designer (the pin function is displayed in the message panel).
Needed for the Gerber P&P files.
It happens when the spice library model shown in dialog is a large file.
Looks like the wxTextCtrl used to displays the library content
creates the crash ( GKT bug?) for large texts.
The fix is to replace this wxTextCtrlt by a wxStyledTextCtrl.
It has advantages (does not crash... and much faster display) and
inconvenients (cannot disable editing).
Fixes: lp:1853161
https://bugs.launchpad.net/kicad/+bug/1853161
Apparently there are some issues with wxString::CmpNoCase() that was
causing the sheet file name case sensitivity test to incorrectly fail.
Converting the name strings to lower case before comparing resolved
the issue.
Add missing check for root sheet when searching sheet hierarchies for
already loaded schematics. This prevents the root sheet from being
omitted when adding new sheets using the root sheet file name.
CHANGED: Make file name tests case sensitive so that schematic sheet
file names on non-Windows systems can be uses as expected.
Warn users when attempting to use schematic file names that only vary
by case sensitivity that doing so will result in a project that is not
portable to Windows.
Fixes lp:1843415
https://bugs.launchpad.net/kicad/+bug/1843415
When dragging a bus the entry is connected to the bus so the wire
connected to the entry (if any) needs to stretch.
While an entry can connect in the middle of bus, it cannot connect
in the middle of a wire.
Fixes: lp:1849973
* https://bugs.launchpad.net/kicad/+bug/1849973
The aperture option created a Connector pad only on the paste layer.
This is incorrect: the SMD type only is acceptable.
5connector is *only* for edge card connectors.
Moreover, The dialog did not even accept the setting defined by this dialog...
- Previously a warning was generated even for not connectable pads
(pads not on copper layers or without pad name).
- The test is now optional and is disabled by default.
(pads without corresponding pin is schematics are a frequent case)
Fixes: lp:1852444
https://bugs.launchpad.net/kicad/+bug/1852444
We must add the new node for the new file in the new directory,
not in the original root directory. The file watcher will also
delete the old node, so there is no point in renaming the file.
Fixes: lp:1852357
* https://bugs.launchpad.net/kicad/+bug/1852357
Revert "Be a bit smarter about moving files through a rename."
Revert "Check for file moving directory and refresh entire tree if so."
This reverts commit f8aea249df.
This reverts commit 8ce04d3362.
This change makes it so that we don't run the event loop inside
the commit. It's not clear this is an issue, but it seems safer
not to.
Fixes: lp:1852589
* https://bugs.launchpad.net/kicad/+bug/1852589
Not able to draw a keepout-area on bottom or internal layers.
This was due to a behavior specific to the footprint editor,
not disabled in board editor.
Fixes: lp:1852847
https://bugs.launchpad.net/kicad/+bug/1852847
Remove not used files:
- markdown2html is not used (we are using "Sundown" tool)
- newstroke_font_without_CJK.cpp is removed.
Due to code optimization the full font works fine without memory issues
-fix also a few very minor compil warnings
In high contrast mode, the holes of buried vias and microvias were no darkened when not on the active layer.
In high contrast mode, the outer circle of buried vias and microvias were alway darkened.
In high contrast mode, when the selected layer is non visible through-vias are now darkend.
Fixes: lp:1844982
* https://bugs.launchpad.net/kicad/+bug/1844982
CHANGED: No longer call schematics noname.sch in standalone mode,
instead don't given them any name so the user can choose on save.
Fixes: lp:1852607
* https://bugs.launchpad.net/kicad/+bug/1852607
Ensure we iterate over all the sub directories and files inside of them
when deleting a directory from the project tree.
Fixes: lp:1852357
* https://bugs.launchpad.net/kicad/+bug/1852357
We have different requirements than sheet paths for netlists,
so going through that code and then doing a lot of conversions
just ends up with a mess.
We now generate the path directly from the SCH_SHEET_PATH.
Fixes: lp:1852353
* https://bugs.launchpad.net/kicad/+bug/1852353
The sort routine requires the value to be true with a is strictly lower
than b. But just inverting the '<' doesn't yield strictly lower, it
includes '>='. This causes items to jump in the list.
Ian McInerney
jean-pierre charras
Jeff Young
M.Scholz
Wayne Stambaugh
Fabien Corona
Seth Hillbrand
evanshultz