Bus submenus weren't sending events because tool wasn't set.
Net names need to be unescaped for display.
Unfolding wasn't drawing the new wire segments.
SCH_LINE_WIRE_BUS_TOOL could get caught in an infinite event handling loop.
Fixes https://gitlab.com/kicad/code/kicad/issues/3796
Scope: NETLIST_ITEM, CONNECTION_TYPE, ELECTRICAL_PINTYPE,
NET_CONNECTION, NETLIST_ITEM, GRAPHIC_PINSHAPE
Note, the pin type enum had PT_ added to the front to prevent
shadowing of the INPUT symbol on msys2 (see discussion at
c17c9960d8)
This also removes vector cover types which do nothing except obfuscate
the underlying implementation.
Mainly changes SCH_SHEET_PINS and CONFIG_PARAM_ARRAY (which will soon
be replaced by Jon's new stuff).
This moves EESchema DLIST structures to rtree. These changes are more
fundamental than the pcbnew changes from 9163ac543888c01d11d1877d7c1
and 961b22d60 as eeschema operations were more dependent on passing
drawing list references around with SCH_ITEM* objects.
For legacy reasons, it stored left and right "spin" as flipped integers in the file format.
But the code handled the flip in multiple locations rather than just doing it on file io.
This change unifies the internal code and does the mapping in the file I/O.
The new connectivity algorithm had a tendency to cleanup
globally, but that could insert undo records from other sheets
into the current screen's undo stack. Needless to say, this
was a recipie for segfaults.
Fixes: lp:1846247
* https://bugs.launchpad.net/kicad/+bug/1846247
The problem is that wxEVT_CHAR_HOOK doesn’t do the key translation
properly. wxEVT_CHAR does, but we only get to that if we skip the
event at the end of the tool’s event processing loop, which most tools
don’t do. (Selection tools, point editors, pickers, and a couple of
others do skip, which is probably why this didn’t get reported earlier.)
I played around with a couple of ways to fix wxEVT_CHAR_HOOK. Most of
them don’t work, and the few egregious hacks I tried weren't cross-
platform.
So I’m changing it so that most tools now skip at the end of their
event loops. I left out a couple that I felt were high risk (length
tuning, for instance). But there’s still enough risk that I’m 100%
sure it will break something, I just haven’t a clue what.
Fixes: lp:1836903
* https://bugs.launchpad.net/kicad/+bug/1836903
Includes the addition of an onSetCursor() handler which must be called
from both the GAL canvas AND the GAL backend (at least on OSX) to prevent
cursor flickering between (for instance) pencil and arrow.
Also includes new architecture for point editors which allows them to
coordiate cursors with the editing tools (so we can switch to an arrow
when over a point).
We were running into various corner conditions where a tool's event
loop would exit while the tool was still active, or the tool would
get popped while we were still in the event loop. (A lot of these
had to do with the POINT_EDITOR's, but not all of them.)
The new architecture:
1) tools always do a Push()/Pop()
2) everyone is responsible for their own pops; no more stack-clearing
on a cancel
3) CancelInteractive events go to all tools to facilitate (2)
It's a bit of a hack because they're statically initialized and
so we can't make use of the _() macro. We do still want it in the
code, however, because the string harvesting is based off of it.
Fixes: lp:1833000
* https://bugs.launchpad.net/kicad/+bug/1833000
Jon Evans
Mark Roszko
Jeff Young
Seth Hillbrand
Ian McInerney
jean-pierre charras
Seth Hillbrand