Default out-of-the-box is no hotkey. Removed all the preference stuff.
Note that the new implementation is a little different: the old one only
operated on a selection with a single item where the new one operates on
all selected items. So if you want the whole track do a 'U' before the 'W'
(or whatever you have Change Track Width assigned to).
Fixes: lp:1844023
* https://bugs.launchpad.net/kicad/+bug/1844023
This adjusts the fix for 1813038 to focus on the duplicate ghost,
preventing the need to unselect/reselect in every cycle. This improves
large move speeds substantially
This is the behavior of previous 5.1 version.
Using the bounding box has advantages, but unfortunately in many cases the footprint position is moved.
If a lot of flip commands are made on the same footprint, it is moved far from its initial position.
When moving a group of items, the allowed snapping layers should be each
layer in the group, not just the first item's LSET.
Fixes: lp:1830164
* https://bugs.launchpad.net/kicad/+bug/1830164
The Get and place tool used to live in selection tool and could activate
the edit tool by stacking calls. Now that it is itself in the edit
tool, we cannot stack another call to the edit tool that runs
immediately, instead we allow the GetAndPlace to finish before beginning
the next tool (Move)
The problem is that wxEVT_CHAR_HOOK doesn’t do the key translation
properly. wxEVT_CHAR does, but we only get to that if we skip the
event at the end of the tool’s event processing loop, which most tools
don’t do. (Selection tools, point editors, pickers, and a couple of
others do skip, which is probably why this didn’t get reported earlier.)
I played around with a couple of ways to fix wxEVT_CHAR_HOOK. Most of
them don’t work, and the few egregious hacks I tried weren't cross-
platform.
So I’m changing it so that most tools now skip at the end of their
event loops. I left out a couple that I felt were high risk (length
tuning, for instance). But there’s still enough risk that I’m 100%
sure it will break something, I just haven’t a clue what.
Fixes: lp:1836903
* https://bugs.launchpad.net/kicad/+bug/1836903
Because the pickers are called with an Activate()/Wait() pair, any
usurping tool gets in between the picker handling the cancel (due
to activation) and the picker client doing a PopTool(). The new
tool is therefore pushed before the old tool is popped.
Fixes: lp:1835907
* https://bugs.launchpad.net/kicad/+bug/1835907
Includes the addition of an onSetCursor() handler which must be called
from both the GAL canvas AND the GAL backend (at least on OSX) to prevent
cursor flickering between (for instance) pencil and arrow.
Also includes new architecture for point editors which allows them to
coordiate cursors with the editing tools (so we can switch to an arrow
when over a point).
We were running into various corner conditions where a tool's event
loop would exit while the tool was still active, or the tool would
get popped while we were still in the event loop. (A lot of these
had to do with the POINT_EDITOR's, but not all of them.)
The new architecture:
1) tools always do a Push()/Pop()
2) everyone is responsible for their own pops; no more stack-clearing
on a cancel
3) CancelInteractive events go to all tools to facilitate (2)
This checks the movement against a maximum value that would place the
selection outside of the valid area for the footprint or board.
Fixes: lp:1833478
* https://bugs.launchpad.net/kicad/+bug/1833478
(cherry picked from commit 845833e8fd)
It's a bit of a hack because they're statically initialized and
so we can't make use of the _() macro. We do still want it in the
code, however, because the string harvesting is based off of it.
Fixes: lp:1833000
* https://bugs.launchpad.net/kicad/+bug/1833000
Jeff Young
Seth Hillbrand
jean-pierre charras
Seth Hillbrand