Non-connected zones are, by definition, not connected, therefore, we
should not knock out thermal reliefs under any case
Fixes: lp:1810989
* https://bugs.launchpad.net/kicad/+bug/1810989
Frame refresh in wxWidgets sets the focus back to indeterminate state
and prevents hotkey action until the focus is captured again. Using
canvas update is the correct method to update the canvas display after
modifying zones/similar
Fixes: lp:1810993
* https://bugs.launchpad.net/kicad/+bug/1810993
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
The standard DIM() macro was not typesafe as it happily deferred errors
to runtime that can be caught at compile time. Replacing it with a
generic C++11 constexpr allows for typecasting, comparison and compile
time error checking.
Devolve the logic as to whether a pad should be numbered or not
to a pad utility function. Add a very simplistic test for this
function (demonstrating how to test BOARD_ITEMs in general).
Fixes: lp:1804787
* https://bugs.launchpad.net/kicad/+bug/1804787
It is very difficult to select 0-width lines and they aren't physical on
the board. Items with this setting in Eagle should revert to the
default in KiCad.
Fixes: lp:1808584
* https://bugs.launchpad.net/kicad/+bug/1808584
Cairo supports antialiasing when rendering but can be slow when set to
sub-pixel mode. This bumps the minimum version of Cairo to 1.12
(available in 14.04 LTS as well as mingw) to support three antialias
settings (fast, good, best) that offer speed/appearance tradeoffs.
This can provide a higher-quality eeschema render as it works on a
per-element basis as opposed to the OpenGL per-screen antialias.
Currently, GAL is initialised to NONE (i.e. off). This causes
issues when Legacy canvas is broken (i.e. GTK3).
This changes the default to GAL Cairo, both in PCB_EDIT_FRAME
init, and in the config load.
Now, when the user starts with no config, they are prompted for
a choice: OpenGL or Cairo, and one of them will be set up, with
Cairo as fall back.
Users on platforms that still support legacy can go to it as normal
from the menu, but it will not be the default in any circumstance.
Fixes: lp:1809997
* https://bugs.launchpad.net/kicad/+bug/1809997
Where we can get away with lower segment counts (localizing an anchor),
we keep the low-def 16 segment count. Intermediate values and values
that are visible to the user are set to high definition. Most are
simply hints to the inflation correction but where they show, the user
show see smooth lines.
Most rounding operations have been shifted to an absolute error
calculation and the ability to adjust zone segment counts has been
removed in 5.1. The remaining elements that use fixed segment counts
are either 18 (DRC) or 32 (plotting). This aligns the punchout segment
count with the higher (32) definition value
wxChoice centers the selection on GTK. So when switching from a
mid-list item to an item at the top, the list is always cut off for
choice lists located on the top toolbar. Using a combobox provides a
drop-down that allows easier access to all elements in the box.
Fixes: lp:1808569
* https://bugs.launchpad.net/kicad/+bug/1808569
The hotkey name "Help (this window)" does not describe what the hotkey
and associated action does. It displays the current hotkey list, so the
action name should reflect that behavior
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Checks for ratsnest enabled prior to calculating and displaying the
local/dynamic ratsnest. Calls the ratsnest clear from selection clear
Notably, it appears that the tool actions do not chain transitions for
the same event. So only a single action (first specified) will be
executed when an event fires unless the actions are executed by separate
tools.
Fixes: lp:1809752
* https://bugs.launchpad.net/kicad/+bug/1809752
This make the use of legacy canvas on GTK3 a default-off
advanced config. Legacy is substantially broken on GTK3
and is of basically no use at all to general users on this
platform.
If the program starts with legacy canvas in the config,
it is forced into a GAL mode, as otherwise it could happen
that the user is stuck and unable to get into pcbnew to change
the setting.
Fixes: lp:1803156
* https://bugs.launchpad.net/kicad/+bug/1803156
While not technically allowed, overlapping polygons can be drawn in
pcbnew. Gerber polygons are strictly simple, however, so we need to
fracture prior to exporting to avoid invalid gerbers.
Rather than depend on proper unlocking for each exit, we move the
connectivity lock mutex into an RAII-type configuration that
automatically unlocks on exit.
Layer bit sets get chosen for the layer name, starting with the copper
layers and then the technicals. Additionally, multi-layer pads are
appended with an indicator that additional layer bits are set.
Fixes: lp:
* https://bugs.launchpad.net/kicad/+bug/
When importing footprints, some are generated with non-standard (e.g.
"mod") extensions. As a last option, we allow the * wildcard to select
these files for import.
Use TesselatePolygon() to draw polygons in Gerbview instead of GLU tesselation, much slower.
Add helper methods in GAL to know if the current GAL engine is Cairo, OpenGL or something else,
useful to optimize drawing code.
This fixes the handling of align/distribute tool when called on locked
items. Locked items cannot be moved but they may be used for the target
of an align/distribute operation.
Fixes: lp:1808238
* https://bugs.launchpad.net/kicad/+bug/1808238
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Previous version had minimum width to account for it being difficult to
click on small lines. This should not be used for filled polygons
Fixes: lp:1808141
* https://bugs.launchpad.net/kicad/+bug/1808141
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
This updates some of the footprint wizard values to use the default KLC
values for silkscreen, fab, courtyard and text.
Also updates the default QFN settings to create a valid footprint
Make sure the view is rebuilt before selecting the new footprints
so that they're shown only in the selection overlay.
Don't start the drag until the dialog is closed so we don't have
a bunch of extraneous mouse warping.
Fixes: lp:1775265
* https://bugs.launchpad.net/kicad/+bug/1775265
This allows people to continue to use the edge-width as a proxy
for board edge clearance until we implement board edge clearance
as a real feature.
Fixes: lp:1797787
* https://bugs.launchpad.net/kicad/+bug/1797787
Graphic lines and polygons are drawn to fit specific areas for which it
is helpful to have the endpoint controlled by the cursor even when
constraining the angle.
Fixes: lp:1805502
* https://bugs.launchpad.net/kicad/+bug/1805502
IsPolygonFilled() replaces the hard coded comparisob with Edge_Cut in code.
For now the polygon is not filled only on Edge_Cut layer.
But in the future, it could be an option for other layers.
Commit 1858b7dca corrected the handling of polygons on the edge cut
layer for board items. This adjusts for the possibility of polygons
in modules on the edge cut layer by applying the module offset/rotation
to the polygon elements.
Like circles, polygons are self-closed elements that define an outline.
This allows them to be used as such for board outlines and cutouts.
Fixes: lp:1795563
* https://bugs.launchpad.net/kicad/+bug/1795563
This allows too turn it on for work without an additional patch.
Also fix a bug in the disable code - when the SVG is enabled,
allow to select SVG files.
Seth Hillbrand
John Beard
jean-pierre charras
Jeff Young
Tomasz Włostowski
Wayne Stambaugh
Maciej Suminski
D4p0up