The problem is that wxEVT_CHAR_HOOK doesn’t do the key translation
properly. wxEVT_CHAR does, but we only get to that if we skip the
event at the end of the tool’s event processing loop, which most tools
don’t do. (Selection tools, point editors, pickers, and a couple of
others do skip, which is probably why this didn’t get reported earlier.)
I played around with a couple of ways to fix wxEVT_CHAR_HOOK. Most of
them don’t work, and the few egregious hacks I tried weren't cross-
platform.
So I’m changing it so that most tools now skip at the end of their
event loops. I left out a couple that I felt were high risk (length
tuning, for instance). But there’s still enough risk that I’m 100%
sure it will break something, I just haven’t a clue what.
Fixes: lp:1836903
* https://bugs.launchpad.net/kicad/+bug/1836903
Includes the addition of an onSetCursor() handler which must be called
from both the GAL canvas AND the GAL backend (at least on OSX) to prevent
cursor flickering between (for instance) pencil and arrow.
Also includes new architecture for point editors which allows them to
coordiate cursors with the editing tools (so we can switch to an arrow
when over a point).
We were running into various corner conditions where a tool's event
loop would exit while the tool was still active, or the tool would
get popped while we were still in the event loop. (A lot of these
had to do with the POINT_EDITOR's, but not all of them.)
The new architecture:
1) tools always do a Push()/Pop()
2) everyone is responsible for their own pops; no more stack-clearing
on a cancel
3) CancelInteractive events go to all tools to facilitate (2)
Also changes the presentation of the string when the checkbox appears
so that the "Changes will be lost" warning isn't hidden by the turndown.
This last part may require conditional compilation as it's undocumented.
Lastly, regularizes the Unsaved Changes strings between the apps.
It's a bit of a hack because they're statically initialized and
so we can't make use of the _() macro. We do still want it in the
code, however, because the string harvesting is based off of it.
Fixes: lp:1833000
* https://bugs.launchpad.net/kicad/+bug/1833000
DIALOG_EXIT was not being laid out correctly after setting the dialog
message. Rather than fix our custom DIALOG_EXIT, wxMessageDialog and
wxRichMessageDialog were substituted as direct replacements for all
of the variants of DIALOG_EXIT. This make message dialogs appear more
consistent because wxMessageDialog uses the default platform message
dialog and wxRichMessageDialog uses the default platform rich message
dialog on windows.
Remove DIALOG_EXIT_BASE as it is no longer required.
Fixes lp:1832899
https://bugs.launchpad.net/kicad/+bug/1832899
If a tool called something like clearSelection while processing a
MOUSE_CLICK, the SELECTION_TOOL will pass the clearSelection
COMMAND_EVENT because it handles it as a transition, not as an
event. Because m_passEvent is effectively global, the tool manager
would then interpret that as passing the MOUSE_CLICK and we'd end
up processing the click by multiple tools.
Return the EDA_DRAW_FRAME class back to common, whence it came (before it was
duplicated into legacy_wx and legacy_gal). Now there is only one
implementation (the GAL one), it doesn't need to be in a separate library.
This simplifies the dependencies for common lib users.
The iterators are not removal safe outside of the class. We provide a
safety clear function that frees the associated memory.
Fixes: lp:1831465
* https://bugs.launchpad.net/kicad/+bug/1831465
It was due to the fact the frame size was set before the draw canvas panel was created,
thus creating incorrect size of the other panel (the message panel)
Fixes: lp:1831389
https://bugs.launchpad.net/kicad/+bug/1831389
It was confusing that the primary frames registered their tools
differently than the other frames. In addition, since the other
frames also added their own tools, foo_actions::RegisterAllTools()
didn't really register all tool but rather those used by the
principal frame (PCB_EDIT_FRAME, SCH_EDIT_FRAME, etc.)
This allows us to make the various netlist and pcb update routines
more atomic and less reliant on carefully sequenced asynchronous
messages.
This is also a prelude to adding support for footprint testing
without a netlist.
Bug #1807567 states the entering 's' in the string search textbox does
not get passed to the text box correctly when in the German language
under windows. This likely means that the main window is firing wxSave
when it detects the 's' key. By adjusting the id for the save and
continue action, we hope to allow the signal to pass through to the
textbox. This commit should otherwise be a NOP.
N.B. This appears to be the result of hooking wxEVT_CHAR_HOOK into
EDA_DRAW_PANEL::OnKeyEvent() (commit
53b1ec8146) that reverses the cascade of
events from bottom up rather than top down. Fixing that is a longer
project and will likely be a side effect of switching fully to the new
tool architecture.
Libpolygon can provide its own includes via target_include_dirs PUBLIC.
This means any linking targets do not need to specifiy them manually.
As common requires polygon, the polygon dep is also now no longer
required downstream of libcommon, as it's transisitvely implied
by libcommon's target_link_libraries.
This resolves a circular dependency previously detected and also
simplifies CMakeLists.
The bitmap definitions (BITMAP_DEF and so on) do not
have any dependencies on other libs, including WX. This
means the bitmaps library can be isolated from the other
dependencies.
Common now depends on bitmaps, and libraries that depend
on common can pick it up from the common target_link_libraries,
as it is PUBLIC. This means a lot of targets no longer
need manual bitmap linkage.
This avoids a circular dependency that was previously reported
by static analysis.
Avoiding pulling in WX and other headers into the include
tree of each bitmap .cpp is a huge speed up (around 10x) in
compilation, and the generated static library is also 10x
smaller (20MB vs 200MB)
Add common as a link library to pnsrouter,connectivity.
THese library do still use common code (including bitmaps,
via base_screen.h) and this allows them to pick up the libcommon
includes correctly.
wxChoice centers the selection on GTK. So when switching from a
mid-list item to an item at the top, the list is always cut off for
choice lists located on the top toolbar. Using a combobox provides a
drop-down that allows easier access to all elements in the box.
Fixes: lp:1808569
* https://bugs.launchpad.net/kicad/+bug/1808569
Fix highlight not cleared by Pcbnew.
Fix highlight not cleared by Cvpcb (missing code).
Add comments. Remove a few now useless printf used for debug
When clicking on a empty area, clear any highligthed symbols
Fixes: lp:1809977
https://bugs.launchpad.net/kicad/+bug/1809977
Put the cursor and pan control TOOL_ACTIONs in ACTION,
and refer to them in that way.
The handlers are currently identical in Pcbnew and Cvpcb,
and Gerbview (and all canvases) can benefit from them as well
if they are in libcommon. Also saves duplicated code.
Fixes: lp:1795855
* https://bugs.launchpad.net/kicad/+bug/1795855
This commit finishes the removal of OpenMP from the KiCad codebase.
Removed in this commit are the OpenMP calls in 3d-viewer and
qa/polygon_triangulation as well as all references in CMakeLists.txt
std::thread is used instead for multithreaded computation
Add Display Settings to Footprint Browser.
Make each of them OpenGL on OSX and Cairo on other platforms.
Allow auto-zoom to be turned off and save last zoom setting.
Make ordering of tools in htoolbar consistent.
Standardize grid and zoom drop-downs.
Fixes: lp:1791667
* https://bugs.launchpad.net/kicad/+bug/1791667
Primary change is to replace most control/window borders with
AUI pane borders. We implement our own AUI border drawing
routine which avoids the ugly one-pixel white frames around
dark canvasses.
Also increases the signal-to-noise ratio of all the pane
creation code in the various frames.
Spooling up a full PLAYER in the background takes too long.
This also fixes bugs around how the tables are saved, although
that was just missing code rather than anything architectural.
Fixes: lp:1785436
* https://bugs.launchpad.net/kicad/+bug/1785436
Drop all uses of wxRAISED_BORDER and wxSUNKEN_BORDER from dialogs and
panels used in main frame windows.
Drop use of wxSP_3DSASH options on all wxSplitterWindow definitions.
Minor dialog alignment and spacing fixes.
This also fixes a bunch of bugs where an error during save would
still close the window (rather than cancelling the close action).
Fixes: lp:1785034
* https://bugs.launchpad.net/kicad/+bug/1785034
This removes the existing constructors so that all parsing must
be explicit and callers are made aware that they need to think
about illegal characters, malformed ids, etc.
Fixes: lp:1783474
* https://bugs.launchpad.net/kicad/+bug/1783474
Ian McInerney
Jeff Young
jean-pierre charras
Wayne Stambaugh
Seppe Stas
John Beard
Seth Hillbrand
Maciej Suminski
Tomasz Wlostowski