kicad/change_log.txt

1965 lines
91 KiB
Plaintext

Change Log for Kicad
Started 2007-June-11
Please add newer entries at the top, list the date and your name with
email address.
2008-Feb-21 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema
added : full text conversion between text, label, global label and hierarchical label
some problems fixed:
- annotation incorrectly cleared.
- reference not copied in component copy.
- incorrect redo when changing the chip name in component edition
bugs not fixed
- undo/redo problems when changing a text type between text, label, global label and hierarchical label
- incorrect annotation in complex hierarchy with multi parts per package (duplicates created).
2008-Feb-20 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema
Fixed bug in getpart.cpp:
eeschema crashed when aborting a new component place command
Global Symbols now have their shapes
Bad global label shape fixed when reading a schematic file
2008-Feb-20 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
specctra_export.cpp fixed the offset problem with freerouter.net.
http://tech.groups.yahoo.com/group/kicad-devel/message/1076
2008-Feb-19 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
Add ZONE_CONTAINER support to the ID_PCB_HIGHLIGHT_BUTT tool and
WinEDA_PcbFrame::DrawHightLight(). Added TYPEZONE_CONTAINER to
GENERAL_COLLECTOR::AllButZones[] so that containers are editable even
when the "Show Zones" toggle is off. This came from using the software
and realizing that if something is visible (zone containers remain visible
even when Show Zones is off) then it should be selectable. Otherwise it is
confusing and frustrating.
2008-Feb-18 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* Start to use BOARD::GetLayerName() in anticipation of configurable layer
names per board.
* Comment out a printf() which will lock up pcbnew when
it is run under kicad project manager and the interprocess fifo gets filled.
* Cross probe was not showing the not found message properly. wxString was
being used for two purposes, input and Printf() destination.
+gerbview
Now loads all gerber files given on the command line, not just one. The
first file is loaded into layer 1 (index 0), the second one is loaded
into layer 2 (index 1) etc.
2008-Feb-18 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema
Fixed bug in gen bill of material (dialog_build_BOM.cpp):
eeschema crashed when created a B.O.M. (i think: unicode version only)
2008-Feb-18 UPDATE Igor Plyatov <plyatov@mail.ru>
================================================================================
+eeschema
Added menu View with all possible elements from the top toolbar.
Find item added in to the Edit menu.
+all
Translated part of IDs to english.
2008-Feb-15 UPDATE Igor Plyatov <plyatov@mail.ru>
================================================================================
+eeschema
Added item "Delete" in "Edit" menu.
Added menu "Place" with all possible elements from the right toolbar.
2008-Feb-13 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
specctra export: now generate unique pin names from module padnames in the
case where there are non-unique pad names within a module. Tested with
Electra demo, and *.dsn files load OK in there as well as in freerouter.
Stopped using reserved layer name "signal" and instead output a full
padstack consisting of all pertinent layers for via, pads, and keepouts.
2008-Feb-12 UPDATE Tim Hanson sideskate@gmail.com
================================================================================
+eeschema
* commiting my changes to allow multiple instances of a given schematic file within a hierarchy:
** internally, m_currentScreen has been replaced with m_currentSheet,
which is a list or 'path' of screens. The path of screens is used to generate
a series of timestamps, which is converted to flat component reference via a look-up
table in the schematic files.
** this means that m_currentScreen is no longer used -- use GetScreen().
** GetScreen is virtual, as some of the dialogs keep around a WinEDA_BaseScreen pointer.
** all sub-sheets in a given schematic must have different names to generate a meaningful netlist.
2008-Feb-12 UPDATE Igor Plyatov <plyatov@mail.ru>
================================================================================
+eeschema
Added item "New" in "File" menu
+all
Russian translation update.
2008-Feb-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* Added case TYPETRACK, TYPEVIA, and TYPEMODULE support to Board::Add() so
that we can over time hide more of the storage architecture of a BOARD and
isolate those dependencies in fewer places.
* Fixed some pad orientation issues in specctra_export.
* Added VIA_MICROVIA & VIA_BLIND_BURIED support to SPECCTRA::makeVIA().
* Commented out the specctra design import menu choice for now, don't have
time or need for this import.
* Specctra export adds 1/2 mil to clearance rules for freerouter so that
the routed board clears our DRC checker OK.
* Session import seems done now.
2008-Feb-7 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
added "const" to SEGVIA::GetDrillValue() const;
added GetDrillValue() to DRC instead of accessing SEGVIA::m_Drill directly.
changed specctra_export so it aborts if all reference designators are not
unique. Unless they are unique we cannot import the routed session. A
good example is the xylinx board which now fails to export.
first rough work on SEGVIA::makeVIA() but needs much more work. Simple
session files with vias at least import. Now encode drill diameter in
padstack name for later session import.
updated todo.txt file.
2008-Feb-7 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
specctra import of *.ses, did tracks and components.
renamed copy_track.cpp to copy_track.cpp.notused
removed copy_track.cpp from pcbnew/CMakeLists.txt
added setlocale() around import and export for float text style.
2008-Feb-6 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
started specctra imports of *.ses and *.dsn, by adding menus to File | Import.
2008-Feb-4 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
specctra_export.cpp now supports blind/buried/microvias. Fixed how modules
are displayed on back of board. Added a circle keepout for each copper-less
through hole.
2008-Feb-3 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* specctra_export.cpp was not exporting the nets correctly, now fixed.
* Had a problem with an isolated pad modification on a single module instance
in the context of several unmodified instances of same module, now fixed.
* Fixed oval pads to make freerouting.net happy.
See: http://www.freerouting.net/usren/viewtopic.php?f=3&t=317#p408
Done with specctra export for now, will think about adding controls (by dialog)
on the export later.
* Beautification of a few modules.
2008-Jan-31 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
remove the old EDGEZONE class.
A ZONE_CONTAINER class is used instead to handle the creation of a new zone outline
2008-Jan-29 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
SPECCTRA export does most items now, except existing tracks. Soon will
need testing.
2008-Jan-28 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
- Better criteria to find starting poind in zone filling: the filling alg. uses
pads, vias and track ends to find where start the filling.
- Added a tool + option in popup menu in track mode (select track width):
when creating a track, if activated: if we starts on an existing track,
the new track takes the width of the existing track
2008-Jan-27 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+all:
I got a patch from Mr. Wayne Stambaugh which makes it possible to compile
infospgm.cpp once and link the same *.o file multiple times.
Jean-Pierre, if you not yet using CMake, you should edit your make.include
so that infospgm.cpp is only compiled once for everything, not once per
program. Wayne is a competent developer who contacted me about contributing.
I consider him a welcome addition to the developers, Dick.
2008-Jan-25 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
* SPECCTRA export does padstacks ok, except that oval pad's arcs need to be split
into quarter circle arcs, and no consideration is given to "layer types".
See page bottom of page 74 of the SECCTRA Design Language Reference, May 2000.
* HISTORY_NUMBER was spelt with a zero.
* Width was spelt as Widht
2008-Jan-25 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
- void Change_Side_Module( MODULE* Module, wxDC* DC ) is now member of class BOARD.
- Better support for micro vias and buried vias (drill files now are useable for board manufacturers)
But not yet tested by a board manufacturer. Be carefull.
Todo: tools to conversion between via through and buried via and buried viad optimisation.
But must works for micro vias (needed for my next board)
(in pcbnew micro vias are blind vias between 2 adjacent layers: micro vias must be enabled
in Dimensions/track and via menu, and placed by ctrl v.
They are intended to connect small pitch BGA pins to the inner layer, and can be drilled by laser
if the hole diameter is small < 0.2mm. A laser can only drill a hole between 2 adjacent layers ).
** Currently use buried via for tests only, not for production **.
2008-Jan-24 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
* Export a specctra *.dsn file includes some padstacks, not ovals yet.
* Many many refinements to specctra.cpp and specctra.h.
* added COLLECTOR::BasePtr(), which is used in qsort. Could have used
* std::sort() instead.
* Wrote D_PAD::Compare()
* updated todo.txt
2008-Jan-24 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Bugs about fill zones removed (not all, of course).
Fixed an old bug in block delete (could crashes pcbnew after deleting footprints).
2008-Jan-23 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
* Export a *.dsn file includes ZONE_CONTAINERs, was actually able to load
a board with zones into the freerouter.net package! No components, traces yet,
just zones and layers. Fixed parsers and Format()ers.
* Rewrote SPECCTRA_DB::readTIME() to dodge a missing strptime() on windows.
2008-Jan-23 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Plot option in GERBER format Plot (Exclude Edge Pcb layer) modification:
- the default is OFF (like odl pcbnew versions)
- this setup is now save in config (is persistant)
In Zone creation, now delete last created corner works.
2008-Jan-22 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
* Actually able now to export a *.dsn file, but the contents of the file
is incomplete, not a complete input BOARD.
* Added DRAWSEGMENT::Show() for debugging.
* Changed specctra.h's POINT to use double for coordinates. Changed format
string for Format()ing a double.
* Changed specctra_export.cpp to actually output an incomplete file.
* Added BOARD::GetCopperLayerCount() and BOARD::GetLayerName().
2008-Jan-21 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
Added specctra_export.cpp, specctra.cpp, specctra.h, dsn.cpp, and dsn.h to
pcbnew's link requirements. Updated CMakeLists.txt to reflect this. This
increased pcbnew's size by 175kb so far. Started the actual export (i.e.
BOARD to DSN::PCB copying logic) which is going into specctra_export.cpp's
void WinEDA_PcbFrame::ExportToSPECCTRA( wxCommandEvent& event ) so that the
huge header file, specctra.h need only be included in one or two *.cpp
files. The specctra export menu support was added to id.h, wxPcbStruct.h,
menubarpcb.cpp, and pcbframe.cpp. After dsn export, I intend to add an
import, and a session file feedback merge. See the revised
how-to-build-kicad.txt for the new boost c++ libraries requirement.
2008-Jan-21 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema:
labels and texts display changed when rotated 180 degres:
horizontal text are now right justified insteed of 180 degree rotated, and are readable.
+pcbnew:
bug 1874663 solved (edit a pad netname does not work very well)
2008-Jan-20 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
On line DRC when creating a zone outline.
Needs more work to display errors DRC.
2008-Jan-18 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+all:
filtering small mouse moves ( < 5 pixels) when clicking.
Starting a wire or a track is now more easily because these small moves do not start a block commnad.
+pcbnew:
rework of drill filles creation (excellon and reports)
needed to have a clean implantation of buried vias and mainly microvia
which involve a more complex drill files generation
This is better to continue work on zones because :
hight density boards = use of BGA = microvias + good zones handling
When a board has buried or blind vias (microvia are blind vias),
pcbnew creates a drill file per layer pair. for a 4 layer board:
drill file for layer1 to layer 2
drill file for layer2 to layer 3
drill file for layer3 to layer 4
2008-Jan-18 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
how-to-build-kicad.txt: added the Boost C++ Libraries installation info
and requirement.
2008-Jan-16 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Move Zone outlines added
Zone outline DRC works (needs improvements)
some bugs solved, but polyline.cpp still needs work.
gendrill: code cleaning.
2008-Jan-14 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
code cleaning:
DRAWSEGMENT class functions moved in the new files class_drawsegment.cpp et .h
2008-Jan-12 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema:
missing footprints in export netlist (bug 1867321)
Affected: PadsPcb converter did not list all footprints
+pcbnew:
fixed: memory not freeed in block copy (minor bug)
Support for micro vias (generation of drill files not finished)
2008-jan-06 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Block commands now works with zones.
Some code cleanning.
2008-Jan-5 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew:
* Added pad_shapes.h and blended it into class_pad.h and PolyLine2Kicad.h.
Renamed the pad shapes in there to avoid namespace conflicts.
RECT became PAD_RECT, CIRCLE became PAD_CIRCLE, etc.
* common.cpp's ReturnPcbLayerName( int layer_number, bool omitSpacePadding )
has commented out code that I tested as part of a possible new scheme to support
custom layer names per project.
* More specctra dsn import export work.
2008-jan-05 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Added: Delete cutout outline in zone popup menu
the GUI about zones is now working.
Some work is needed ( a zone in a zone of the same net is not merged )
Currently No DRC for outlines
2008-jan-04 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
More about zones:
Outlines can be edited. Outlines are merged if needeed.
Currently No DRC for outlines
2008-jan-01 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+all
wxstruct modified and wxPcbStuct.h added:
classes relatives to pcbnew, cvpcb and gerbview are moved in wxPcbStuct.h
2007-Dec-29 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
First draft (and code..) about new zone handling, using polygons to define an outline.
Now currently not useable because the fill function (and many other important functions) is not implemented.
Many functions are not yet implemented: merging zones, cutout, DRC ...
Nevertheless, one can create, modify edit and save zone outlines
2007-Dec-23 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+all
* Because of the discussion 4 months ago about using Boost::Python, and
because of an excellent boost::ptr_vector class, I want to make some of the
boost libraries be necessary for building Kicad. These would be:
1) boost pointer container library (immediately)
http://www.boost.org/libs/ptr_container/doc/ptr_container.html
See the work in specctra.cpp to see where this is going:
typedef boost::ptr_vector<ELEM> ELEM_ARRAY found within class PARENT.
I found that gcc 4.2.1 was complaining about the standard ubuntu libboost-dev
package and would not compile ptr_vector class. But the svn of boost
fixed this.
2) boost::python when building python in.
* Added FIND_PACKAGE(Boost) to CMakeLists.txt
2007-Dec-22 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+all
added strlower() to common.h and string.cpp.
fixed compiler warnings in common/gr_basic.cpp and pcbnew/clean.cpp
+pcbnew
started the DSN file import/export for SPECCTRA routers, adding dsn.cpp and
specctra.cpp, with "stand alone" compile support for it in pcbnew/CMakeLists.txt.
2007-Dec-17 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
WinEDA_PcbFrame::Other_Layer_Route() was leaving in the bridging segment
when the DRC denied the via insertion.
2007-Dec-17 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
some changes about zones: enhanced dialog, and files reorganisation
2007-Dec-14 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
WinEDA_PcbFrame::Other_Layer_Route() now returns bool, so that if the DRC
would not allow the new via placement, then it can be checked and the layer
change can also then be aborted. Previously the layer change would happen
in mid track even if the via could not be placed.
2007-Dec-13 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* surbrill.cpp's int WinEDA_PcbFrame::Select_High_Light( wxDC* DC )
was re-written to use the GENERAL_COLLECTOR, and the scanList is set to
give pads a higher search priority than tracks, vias or zones.
The objective was to use the pad if possible, rather than a track on a pad,
so the pad can be sent to eeschema. Finding the track only (even though
on a pad) would not send anything to eeschema.
2007-Dec-12 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* Fized zone drawing bug in svn HEAD only.
pcbnew/zones.cpp, see:
http://tech.groups.yahoo.com/group/kicad-users/message/2993
2007-Dec-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+all
* Fixed hotkey table for '+' and '-' bug. The lookup table in
common/hotkeys_basic.cpp had bad entries for + and -. These hotkeys
were not working on Linux.
* Added polygon directory to Doxyfile.
2007-Dec-09 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+cvpcb:
listboxes.cpp FootprintListBox::m_ActiveFootprint member was not initialized.
Can crash cvpcb (WINDOWS only, i believe)
2007-Dec-09 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
changes in file organisation and classes to prepare zone redesign. No real new code.
class zone functions and definitions moved in class_zone.h and .cpp
2007-Dec-07 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew
Very minor bug in drill map : inaccurate via shapes (I believe EXCELLON drill file has no problems)
2007-Dec-06 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+all
Solved zoom key command problems (under linux and windows)
(seen http://sourceforge.net/tracker/index.php?func=detail&aid=1844960&group_id=145591&atid=762476)
+pcbnew
solved bug when loading a footprint in modedit: invisible text attribute was lost (trunk and tag)
2007-Dec-4 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
added the D() macro to fctsys.h to ease conditional debug printf()s.
worked on http://sourceforge.net/tracker/index.php?func=detail&aid=1844960&group_id=145591&atid=762476
but could not resolve it in 1/2 day.
2007-Dec-4 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* drc.cpp and dialog_drc.cpp update.
Added double click support on a MARKER or unconnected DRC_ITEM in the listboxes.
On Linux, it sometimes pops up the menu from PcbGeneralLocateAndDisplay()
for some reason after repositioning the cursor. That is not intended, but
after several attempts to work around it, I realized it is not so bad to
have this happen.
* Added right click popup menus to the list boxes. User must first select
the item he wants to go to, as the right click does not change the selection.
* Added WinEDA_BasePcbFrame::CursorGoto( const wxPoint& ) by factoring it
out of pcbnew/find.cpp
Done now, its ready for folks to start using it and testing it.
2007-Dec-02 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema:
Solved an annotation problem: in multiple parts per package components,
when sorted by position, parts were not grouped by package.
2007-Dec-2 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
drc.cpp and dialog_drc.cpp intermediate update.
2007-Nov-30 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* added virtual GetPosition() to BOARD_ITEM and derivatives.
* added classes DRC, REPORT_ISSUE, DRC_ITEM and rearranged drc.cpp entirely
to comprize the DRC class. The result has finer granularity of functions
and each is fairly well documented in English, see drc_stuff.h.
Keeping old stuff commented out at bottom of drc.cpp until some more usage
and testing is done.
* Made the DRC dialog modeless, so it can sit off to the side while the MARKER
are inspected one by one.
2007-Nov-29 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Removed a bug (function block() ) which crashes pcbnew when erasing a zone by block delete
2007-Nov-27 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* changed class MARQUEUR to class MARKER name only.
* Moved BOARD's MARKERs from m_Drawings to vector<MARKER*> m_markers so
they can be easily deleted and navigated to from the drc dialog.
* deprecated the MARKER::Unlink() function.
* Added
BOARD::Add( BOARD_ITEM*, int )
BOARD::GetMARKER(int)
BOARD::Delete( BOARD_ITEM* )
BOARD::DeleteMARKERs();
* Changed BOARD::~BOARD() to use DeleteMARKERs().
* Revised screen drawing routine to know about BOARD::m_markers.
* Revised BOARD::Visit() to know about BOARD::m_markers.
* Revised pcbnew/find.cpp to know about BOARD::m_markers.
* removed wxYield() from drc.cpp
2007-Nov-26 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
DRC code and dialog rework start. This breaks DRC, until I get out the
other end of the tunnel.
2007-Nov-24 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+pcbnew
* dialog_track_options uses a portable technique for SetFocus(), namely the
function OnInitDialog( wxInitDialogEvent& event ).
* started work on dialog_drc, not checked in. basic wxHtmlListBox is working with dummied text.
+all
makefile.include's now use CXX instead of CC for compiling.
2007-Nov-15 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+pcbnew:
Removed a bug (function Delete_Zone() ) which crashes pcbnew when erasing a zone by popup menu
2007-Nov-13 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema & pcbnew
* The "Page Settings" dialog box has been enhanced; it now includes a
wxStdDialogButtonSizer, and is also now designed to be expandable.
+ pcbnew
* The "DRC Control" and "Netlist:" dialog boxes have also been enhanced. Each
of those dialogs now includes a wxStdDialogButtonSizer and a "Cancel" button,
(so each of those dialogs can now (otherwise) be cancelled by pressing the
"Esc" key), and is also now designed to be expandable.
2007-Nov-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
Fixed modedit.cpp bug which occurred when selecting a non pad item (such
as a text field) in the module editor, then selecting Dimensions -> Pad Settings
in the module editor.
2007-Nov-11 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema & pcbnew & gerbview
* The "Colors" dialog box has been enhanced; the distance between adjacent
controls now increases (and in both horizontal and vertical directions)
when that dialog is resized. And the "Cancel" button is no longer centre-
justified; it is now right-justifed instead.
+ eeschema
* A wxStdDialogButtonSizer is now used within the "EESchema Colors" dialog box,
meaning that the sequence of the "OK", "Cancel", and "Apply" buttons within
that dialog now depends upon which (OS) version of KiCad is being used (and
thus matching the nature of the corresponding dialogs within Pcbnew and GerbView
in that regard). (As of yet, the vertical distance between adjacent controls
does not increase when this dialog is resized, but that aspect will also be
implemented when time permits.)
+ gerbview
* The "GerbView Layer Colors:" dialog box has been updated, and is now similar
in nature to the corresponding dialogs within EESchema and Pcbnew. Tool tips
have also been provided for the "Show All" and "Show None" buttons.
2007-Nov-10 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+eeschema:
More comprehensive dialog in netlist plugin interface.
Eeschema configuration now shows the plugin netlist list
2007-Nov-09 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ 3d-viewer
* The 3d_canvas.cpp file has been updated to use a const parameter, as suggested
within (Bug) Request ID 1828487.
+ pcbnew
* Sizers have now been provided for the "Pcbnew Layer Colors:" dialog box (previously
identified as the "Colors:" dialog box), and tool tips have been provided for the
"Show All" and "Show None" buttons.
* The reglage.cpp file (which is not currently used) has been removed, and replaced
with reglage.cpp.notused.
2007-Nov-02 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
removed not used files
2007-Nov-07 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ all
* The common/svg_print.cpp, common/svg_print.h, and common/svg_print.pjd files (which
are not currently used) have been removed, and replaced with svg_print.cpp.notused,
svg_print.h.notused, and svg_print.pjd.notused. And common/makefile.include has
also been updated so that none of those files are now listed at all.
+ eeschema
* A "Cancel" button has now been provided within each of the "Component properties",
"EESchema Annotation", "EESchema Erc", "Global Label properties", "Label properties",
and "Text properties" dialog boxes, and each of those dialogs can now (otherwise) be
cancelled by pressing the "Esc" key. (In due course, each of those dialogs will be
refined yet further; this is just an incremental enhancement.)
* The eestatus.cpp file (which is not currently used) has been removed, and replaced
with eestatus.cpp.notused.
2007-Nov-05 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema
* The previously provided "Close" button within the "Netlist" dialog box has
now been replaced with a "Cancel" button, and this dialog can now (otherwise)
be cancelled by pressing the "Esc" key. General cleanup and beautification of
eeschema/netlist_control.cpp.
+ pcbnew
* The color of each text string provided within the "Swap Layers:" dialog box is
now set to blue for each string specifying that the associated layer is *not*
being swapped with any other layer, or to fushia for each string specifying that
the associated layer *is* being swapped with another layer. (This change was
made after being suggested by Dick Hollenbeck.)
+ gerbview
* The color of each text string provided within the "Layer selection" dialog box
is similarly now set to blue for each string specifying that the associated
Gerber layer is *not* being exported to any pcbnew layer, or to fushia for each
string specifying that the associated Gerber layer *is* being exported to a
pcbnew layer.
2007-Nov-2 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
fixed a crashing bug which happened if you "dragged" a module with
tracks. Then deleted one of the pad connected tracks, then deleted the
next track attached to the first one. Memory was being corrupted because
PcbGeneralLocate() and display was not being called on the 2nd track to
be deleted because the m_Flags test:
bool ItemFree = (GetCurItem()==0 || GetCurItem()->m_Flags==0);
was returning false. Solution was to SetCurItem(NULL) after deleting a
TRACK. This makes sense, SetCurItem() is used for designating a "selected"
item, and a deleted TRACK is not even in the BOARD anymore and should not
be selected or selectable. I think this bug may have been causing spurious
crashes for the last couple of months.
2007-Nov-02 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+all:
solved: eeschema, pcbnew and cvpcb did not find libraries when they were
in the default library path, but in a subdirectory
(this is because the default path was not added to the name if the name had
already a path)
2007-Nov-02 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* Sizers have now been provided for the "Swap Layers:" dialog box, and the
previously provided radiobuttons have been replaced with buttons and static
text strings. (In the previous version of this dialog, radiobuttons were being
used in an inappropriate manner. The most "orthodox" way of implementing the
functionality within this dialog would be to provide a combobox for each layer,
but as up to 30 strings would be needed within the dropdown list associated with
each of those controls (one string for each of the layers, and another string to
deselect the layer), such controls would be less than user-friendly. Hence a
button is now provided for each layer instead (and which, like the previously
provided radiobutton, invokes the "Select Layer:" dialog box after being clicked
on). Two static text strings are also provided for each layer, with one of them
being used to identify that layer, and the other being used to identify which
layer that each layer is currently being swapped to.) The previously provided
"Select" and "Deselect" buttons are no longer required, and are thus no longer
provided.
+ gerbview
* The "Layer selection" dialog box (invoked during the "Export to Pcbnew" command)
has similarly been updated. (This dialog did use spacers before, but once again,
the previously provided radiobuttons were being used in an inappropriate manner.)
2007-Nov-01 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* Provided new definitions of FIRST_COPPER_LAYER and LAST_COPPER_LAYER within
include/pcbstruct.h, and used those definitions within various other files.
Beautified and generally refined 3d-viewer/3d_draw.cpp and pcbnew/plotgerb.cpp.
2007-Oct-31 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+kicad:
rename mdiframe.cpp to mainframe.cpp
create commandframe.cpp to handle the command frame (which have the 4 "fast launch" buttons)
2007-Oct-31 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
* Added Doxygen configuration file, whose standard name is Doxyfile. Output
is set to go to ./doxygen directory just off the project tree.
* Added a note to todo.txt which asks folks to start using "Doxygen compatible"
comments in member functions and classes. Run Doxygen on the project, then
look at the documentation for class INSPECTOR as an example.
+ pcbnew
* zones.cpp, Trace_Pcb(), & EDGE_ZONE class:
Reversed the usage of EDGE_ZONE::Pnext and Pback in the list management to be
consistent with other classes and with BOARD_ITEM::IterateForward() and
BOARD::~BOARD().
* Fixed a display bug when high contrast mode is enabled and the track tool
is selected.
2007-Oct-31 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+all:
gcc 4.2.1 compatibility: change char * to const char * whenever it was necessary,
mainly in .xpm files
2007-Oct-30 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
added BOARD_ITEM::Save() and to all derived classes as well. Made virtual
and removed all UI code from these utility functions.
removed WriteDesc() functions from all BOARD_ITEM derived classes, although
Keeping old ones in commented out form for a while for reference.
@todo: delete these from *.cpp files eventually.
zones.cpp, clean up in prep for enhancements.
+ gerbview
fixed bug which came about when BOARD::~BOARD() started deleting the objects
that a BOARD owns. export_to_pcbnew.cpp was not consistent with this
design and was crashing. Also, export_to_pcbnew.cpp now uses the simple
BOARD::Save() function. It was another place to maintain the PCB file format,
rather than simply putting that knowledge into one place like BOARD::Save().
+ all
beautified gr_basic.cpp and made CLIP_LINE macro a static inline function.
2007-Oct-30 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+cvpcb: listboxes.cpp problem solved: exists only under windows
now apply to windows only, because this Workaround creates a problem undex linux
+others:
some very minor problems solved
+eeschema:
in B.O.M.: the footprint field can be added to the field list
2007-Oct-29 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+cvpcb: listboxes.cpp problem solved: Workaround for a curious bug in wxWidgets:
if we switch from a long list of footprints to a short list (a filtered footprint list),
and if the selected item is near the end of the long list,
the new list is not displayed from the top of the list box
+eeschema:
Implemented: graying in/out of "Edit/Undo", "Edit/Redo" menu items,
when Undo/Redo stack is empty/filled.
+pcbnew:
Implemented: action for ID_POPUP_PCB_DELETE_MARKER
2007-Oct-27 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all:
remove unused files.
some translations
+cvpcb:
set flag wxFRAME_FLOAT_ON_PARENT when create the footprint 3D frame and the
display frame
minor other changes
+ pcbnew:
Use collector class to locate items in modedit.
This is a big enhancement,
but a small work for me because Dick made all the work.
2007-Oct-26 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
Add class_marker.cpp and class_marker.h and move MARQUEUR functions in class_marker.cpp
Change MARQUEUR::HitTest to take in account the zoom level.
change global var EDA_Appl to g_EDA_Appl
2007-Oct-25 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ cvpcb
* Fine-tuned contents of dialog_display_options.cpp, dialog_display_options.h,
and dialog_display_options.pjd, so that the controls within the associated
("Display Options") dialog box now also expand if that dialog is expanded.
+ all
* The share/selcolor.cpp file (which is no longer used) has been removed, and
replaced with share/selcolor.cpp.notused
2007-Oct-24 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ cvpcb:
2 missing .prj files added (and updated)
dialog_display_option.cpp is rebuild from its dialog_display_option.prj source
2007-Oct-23 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema
* Sizers have now been provided for the "EESchema Preferences" dialog box,
together with "OK", "Cancel", and "Apply" buttons. And an additional bitmap
button and checkbox have also been provided for the purpose of editing the
color and visibility of the grid.
2007-Oct-21 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ all
* Provided an MAYBE_RESIZE_BORDER field within all of the .pjd files (used by
DialogBlocks), and restored the MAYBE_RESIZE_BORDER field to cleaningoptions_dialog.h
2007-Oct-21 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
added UIpolicies.txt
2007-Oct-21 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
rename dialog_clean_pcb.pjd to cleaningoptions_dialog.pjd,
accordind to the corresponding cpp filename.
enter the new tool tips in cleaningoptions_dialog.pjd.
+all:
USE_RESIZE_BORDER is now defined (default) in fctsys.h.
Therefore, under windows, dialogs are now resizable (like under unix)
2007-Oct-21 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema & pcbnew & gerbview
* Sizers have now been provided within the "Colors" dialog box.
2007-Oct-19 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* "Clean tracks" changed to "Track operations".
* Housekeeping on clean.cpp completed.
Added static void ConnectDanglingEndToVia( BOARD* pcb ) in clean.cpp which
extends tracks to via centers. Call it from "extend to pads", works nice.
* Added tooltip text to cleaningoptions_dialog.cpp's m_ConnectToPadsOpt
but don't know if DialogBlocks will parse this backwards.
* Made compilable, somebody broke #define VIA_???? s throughout. Would not compile.
* SEGVIA::SetPos() & GetPos() added.
2007-Oct-17 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
Removed enhancements in connectivity computation because
rastnest computation does not work (errors) with short track segments
(lenght < width) . This is not a bug, but an algorithm problem, so
I must work on algos.
2007-Oct-17 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* Rolled back previous changes (made in revision 336) that edited the values of
vias' Shape property (following feedback from Jean-Pierre Charras concerning
the true significance of that property).
2007-Oct-13 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
remove a change for Read VIA because via attributes
(TROUGH VIA, BLIND VIA or BURIED VIA) are autorisations for layer connection,
and are not a real layer indicator.
If a via connect layers from copper to component, it can have a BURIED VIA attribute.
the meaning is for this via the layer pair can be changed for other layer pair
if after editing this via connect 2 tracks which are only int internal layers,
its layer pair can be changed.
If a via has a TROUGH VIA attribute, it connects ALL layers, whenever tracks
connected to it.
Note: curenty: only TROUGH VIA are handled.
Other types (BLIND VIA and BURIED VIA) are only experimental.
A **lot** of code is needed for a full support.
enhancements in connectivity computation
2007-Oct-15 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* Made some changes involving vias so that these would have the correct value
of the Shape property assigned to them - while being created, and while files
are being saved, and while files are being loaded.
2007-Oct-14 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew:
* housekeeping and translation to English on bottom third of pcbnew/clean.cpp.
No algorithm changes were intended, only improved readability.
* my todo: figure out how to intercept double clicks on a wxWidgets text control
so I can complete the work I started on MARQUEUR error tracking.
2007-Oct-13 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
ratsnest.cpp translated into english.
Many infos on the LEE algorithm used here added.
todo (by myself): connect.cpp translation.
onrightclick() bug (created by last change) solved: one could reselect an item,
while moving a previously selected item (pcbnew crashes).
2007-Oct-13 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema
* The previously provided "Quit" button within the "List of Material" dialog box
has been replaced with "OK", "Cancel", and "Apply" buttons. Greater consistency
has also been achieved after clicking on the "Create List" button; none of the
prevailing settings are subsequently saved (previously, some, but not all, of
the settings were subsequently saved). (However, settings can still be saved by
clicking on either of the "OK" or "Apply" buttons instead.) Assorted cleanup
and beautification of associated source code.
* The genliste.cpp file (which is no longer used) has been removed, and replaced
with genliste.cpp.notused
2007-Oct-12 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
* m_NetCode is now private or protected throughout.
added SetNet() and GetNet() to all classes which have this member name.
ditto for m_Sous_NetCode, for which there is now SetSubNet() and GetSubNet().
+ pcbnew
added more disambiguating text to the PcbGeneralLocateAndDisplay() popup
menu for tracks. We need all the info we can get there I found after using
the software for many hours.
Jean-Pierre:
I never thought I would find a greater problem in using Kicad than having to
lay down all the ground and power tracks, rather that just linking vias into
pre-established zones or "tagged layers".
But I have, hundreds of my tracks and vias are showing
unconnected under my BGA, (where say the track or via is NetCode==0) and it
should not be, because the damn track ties the BGA pad to a nearby via.
How can the software be made to think these three items are on the same net,
without re-entering all the damn tracks?
This issue has been coming up for months on the user list, it must be dealt with now.
There is always the same lame answer, "make sure your tracks go to the center of the pads".
Nonsense, the software picked the track end points, not me, and grid was on when it did it.
There are bugs here.
Does Recalcule_all_net_connexion() work, and why is not called from anywhere?
2007-Oct-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* D_PAD::Draw() refinements.
* WinEDA_DrawFrame::SetToolID() will redraw the DrawPanel if the track
button is selected or de-selected and the high-contrast mode is in play.
* If high-contrast mode is in play, the Select Layer Pair dialog completion
will redraw the DisplayPanel, now that SMD pads' colors are so dependent
on these variables.
2007-Oct-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* D_PAD::Draw() so that it shows SMD pads as greyed out when in high contrast
mode and not on current layer. Slight variation on this when laying down
tracks: m_Route_Layer_BOTTOM or m_Route_Layer_TOP layers' SMD pads are
not greyed out.
* Changed English UI text for "Cotation" to "Dimension".
2007-Oct-11 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* The "Target Properties" and "Pads Global Edit" dialog boxes can now (otherwise)
be cancelled by pressing the "Esc" key, and the caption of the "OK" button
within the latter dialog box has been capitalised (so that an icon is now
provided within that button within the Linux version of KiCad).
* The pcbpiste.cpp file (which is no longer used) has been removed, and replaced
with pcbpiste.cpp.notused
+ cvpcb
* The affiche.cpp file (which is no longer used) has been removed, and replaced
with affiche.cpp.notused
2007-Oct-11 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
* The previously provided "Exit" button within the "Colors:" dialog box has been
replaced with "OK", "Cancel", and "Apply" buttons, and the code for editing the
visibility of the Grid layer from that dialog now is "cleaner" than before.
Details associated with buttons within that dialog box moved from set_color.cpp
to set_color.h (matching implementation for GerbView's corresponding dialog box).
* Fixed bug which previously prevented the Copper layer from being selected as the
current layer when only one copper layer is enabled (and made some modifications
to the code for selecting the next copper layer and previous copper layer).
+ gerbview
* The code for editing the visibility of the Grid layer from the "GerbView Layer
Colors:" dialog box is "cleaner" than before, and assorted other beautification.
+ eeschema
* The options.cpp file (which is no longer used) has been removed, and replaced
with options.cpp.notused
2007-Oct-10 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* bug fix: prevent OnRightClick() from calling PcbGeneralLocateAndDisplay()
when creating a new track.
* bug fix: popup menu was not handling Mires, because the collector was not
being asked to find them.
* added TRACK::ShowWidth() and call it from BOARD_ITEM::MenuText(). There was
not enough information in Selection Clarification at a busy junction to
make a reasonable choice.
* SEGVIA::MenuText() shows via width, rather than net_code.
* Beautified ratsnets.cpp, I would like to understand it better. It would help
if the comments were in English.
+ all
* Changed English UI text "Mire" to "Target" according to this post:
http://tech.groups.yahoo.com/group/kicad-users/message/1380
* rewrote msgpanel.cpp so it retains wxStrings and therefore can repaint its
window when being uncovered, resized or whatever.
2007-Oct-9 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
changed pcbnew/onrightclick.cpp so that a right click only shows the
Selection Clarification menu if there is no selected object or if the
click is in a position different from where the selection was previously
made.
2007-Oct-09 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema:
cross-probing minor bug solved ( due to last modification): pins/pads not probed
2007-Oct-08 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ gerbview
Display on screen now updates properly (in Linux version) after clicking on
the "OK" button provided within the "GerbView Layer Colors" dialog box.
2007-Oct-7 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema
create new file cross-probing.cpp
move RemoteCommand() to cross-probing.cpp and create SendMessageToPCBNEW()
+ pcbnew
bug in move pad fixed (could crash pcbnew)
Small change in selection clarification (side effect removed):
- Escape or click on title does not show the next popup menu.
- the title is displayed under linux
- definition CUIVRE_N translated into COPPER_LAYER_N
2007-Oct-07 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ all
* Various dialog boxes can now (otherwise) be cancelled by pressing the "Esc" key.
(Some dialog boxes still require attention in that regard though, so that task
is not yet complete.) And the captions of the "OK" button within various dialog
boxes have been fully capitalised (meaning that an icon is now provided within
each of those buttons within the Linux version of KiCad).
* DIALOG_STYLE (defined within include/wxstruct.h) now includes MAYBE_RESIZE_BORDER
field. (Refer to 2007-Oct-2 UPDATE notes for the relevance of this.)
* Beautification and house keeping.
+ eeschema
* The editpart.cpp and libedpart.cpp files (which are no longer used) have been
removed, and replaced with editpart.cpp.notused and libedpart.cpp.notused
+ cvpcb
* Additional "OK", "Cancel", and "Apply" buttons have now been provided for the
"Options" dialog box which lists various display options for footprints.
+ pcbnew
* Invoking the "Select Layer Pair:" dialog box is no longer possible whenever only
one (copper) layer is currently enabled. And it is no longer possible to select
the same layer to be both the Top Layer and Bottom Layer (for any Layer Pair).
* Deselecting layers during the "Swap layers" command is now more user-friendly,
due to the provision of an additional "(Deselect)" radiobutton within the (child)
"Select Layer:" dialog box (which is always invoked whenever a different
radiobutton within the "Swap Layers:" dialog box is clicked on). (It had
previously been necessary to cancel the "Select Layer:" dialog box before being
able to click on the "Deselect" button within the "Swap Layers:" dialog box.)
* Definition for NB_LAYERS changed from (EDGE_N + 1) to (LAST_NO_COPPER_LAYER + 1)
(Although EDGE_N is currently the "last" layer, that wouldn't necessarily still
be true if any additional layers are ever defined in the future.) And comparisons
to 29 (or 28) have been replaced with comparisons to NB_LAYERS (when appropriate).
+ gerbview
* The previously provided "Exit" button within the "GerbView Layer Colors" dialog
box has been replaced with "OK", "Cancel", and "Apply" buttons; and both the
visibility and color of the Grid layer can now be edited from the same dialog.
* Deselecting (Gerber) layers during the "Export to Pcbnew" command is now more
user-friendly, due to the provision of an additional "(Deselect)" radiobutton
within the (child) "Select Layer:" dialog box (which is always invoked whenever
a different radiobutton within the "Layer selection:" dialog box is clicked on).
(It had previously been necessary to cancel the "Select Layer:" dialog box before
being able to click on the "Deselect" button within the "Layer selection:" dialog
box.)
* The "Export to Pcbnew" command now requires at least one Gerber file to have been
already loaded. And Gerber files can now be loaded into any of the 32 (Gerber)
layers provided. (It had previously been necessary to avoid having any gaps within
the sequence of used Gerber layers.)
2007-Oct-6 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
create new file cross-probing.cpp
move RemoteCommand() and SendMessageToEESCHEMA() to cross-probing.cpp
2007-Oct-3 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
made BOARD_ITEM::UnLink() virtual
added BOARD_ITEM::DeleteStructure().
added EDA_BaseStruct::DeleteStructList()
deleted gerbview/struct.cpp, pcbnew/struct.cpp,
BOARD::~BOARD() now deletes objects that it owns.
Collectors now finds MARQUEURs also
added MARQUEURS::Display_Infos()
added MARQUEURS::HitTest()
2007-Oct-2 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
The lack of border resizing in dialogs has been a problem. In my world,
dialog boxes are resizable. I use large fonts, I like to see stuff.
So now for __UNIX__ they are resizeable, for windows not.
See fctsys.h and the #define for MAYBE_RESIZE_BORDER. For windows it defaults
to zero which means resizeable is not featured. A compiler command line
option of "USE_RESIZE_BORDER" can override this windows default.
2007-Oct-01 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew/eeschema
Cross-probing pcbnew to eeschema:
A left click on a pad in pcbnew moves the eeschema cursor on the corresponding component pin
A left click on a footprint ref or value in pcbnew moves the eeschema cursor on the corresponding component ref or value
A left ckick on a footprint moves the eeschema cursor on the corresponding component anchor
+ pcbnew
removed drc.cpp change line 584, and translate comments in english.
nothing broken:
-> a pad with its netcode = 0 means the pad ** must be left unconnected ** (not attached to * a net).
-> a track with its netcode = 0 means the track is not attached to a net (cannot be connected to any pad).
2007-Sep-30 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
Added dedicated Show() function for SEGVIA. Enhanced BOARD_ITEM::MenuText()
for SEGVIA.
2007-Sep-29 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* drc.c made a change near line 584 to comment out pt_pad->m_NetCode test against
zero. This was preventing me from laying out my board. It's possible that
this broke something else, but it is also clear that something was broke before
this change, because I could not put down some tracks.
* beautification, house keeping.
2007-Sep-29 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
create new file onleftclick.cpp
move onleftcligk() and onleftDcligk() from edit.cpp to onleftclick.cpp
2007-Sep-27 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
test case for OnLeftClick() handling enhancements.
TAB key removed, because is not needed for block selection and double click.
(SHIHT ou CTRL or ALT key is sufficient to suppress the popup menu
if needed for a double click )
Some work is still needed, of course
+ pcbnew
Color grid setting now works
2007-Sep-26 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
test case for OnLeftClick() handling from a release circumstance.
a few simple changes to void WinEDA_DrawPanel::OnMouseEvent( wxMouseEvent& event ),
but they affect all programs in a subtle way.
TAB key allow double clicking, but is not needed for block selection.
+ pcbnew
GENERAL_COLLECTOR::GetCount() returns int, not unsigned. Was tired of the
compiler complaining when using an int ndx.
2007-Sep-25 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* removed reference to global display options DisplayOpt.DisplayZones in
collectors.cpp so collectors.cpp can continue to be used in multiple future
(non-display related) general contexts. I don't want unnecessary dependencies
in there. The way to completely ignore a type is to exclude it from scanList.
The way to sometimes ignore a type is to add support for this in COLLECTORS_GUIDE.
* Moved TYPEZONE to end of AllBoardItems, added GENERAL_COLLECTOR::AllButZones to
provide support for DisplayOpt.DisplayZones.
* Added aHotKeyCode to PcbGeneralLocateAndDisplay()
+ gerbview
* viewer was getting stuck in a loop when loading a bad gerber file. Fixed
the bug, but line 223 through 225 of readgerb.cpp needs review.
* beautified a few files with uncrustify, (any I had to look at).
2007-sept-25 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
* add class_board_item.cpp file and move BOARD_ITEM::MenuText() and BOARD_ITEM::MenuIcon() in it
* Add zone detection, forgotten in PcbGeneralLocateAndDisplay()
+ class_collector.h:
add void COLLECTOR::Remove( unsigned int item_position ), needed by zone detection, see PcbGeneralLocateAndDisplay
2007-Sep-25 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ gerbview
The "Exit" button previously provided within the dialog box invoked from the
"Preferences -> File ext" menu entry has now been replaced by "OK" and "Cancel"
buttons. Similarly, the "Accept" button previously provided within each of the
dialog boxes invoked from the "Preferences -> Options" and "Preferences -> Display"
menu entries has now been replaced by an "OK" button. And each of those three
dialog boxes can now (otherwise) be cancelled by pressing the "Esc" key.
2007-sept-22 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
* small change in hotkeys handling
(Ki_HotkeyInfo: new member m_IdMenuEvent to call an existing event handler from a hotkey list)
+ eeschema:
* added drag component in pop up menu and hotkeys
* plot svg format: incorrect arc draw fixed
2007-Sep-22 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
GENERAL_COLLECTOR::Collect() was skipping thru hole pads even though they
were visible.
Highlight tool now sends message to eeschema when a pad is selected.
2007-Sep-20 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ eeschema
* beautify, add debug Show() functions, changed ReturnFieldName()
to return "const wxString&" for speed, added GetFieldValue().
* tracking down questionable behavior (a bug?) in erc regarding pwr_flag, still looking
2007-sept-20 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
* hotkeys handling finished
+ pcbnew
* bug fix: a subtle bug in place via : partial drc only was made.
2007-Sep-14 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* controle.cpp, added Function AllAreModulesAndReturnSmallestIfSo() which is
called from PcbGeneralLocateAndDisplay()
* onrightclick.cpp changed to calls to BOARD_ITEM::MenuText(), and switched
to member functions for createPopupMenus() so we can get all the state
information we need for the proper menus.
* BOARD_ITEM::MenuText() got new argument BOARD*, and elaboration for
TRACKs and VIAs and Pcb Graphics.
* Fixed a problem in GENERAL_COLLECTOR::Inspect() so it now knows that MODULEs
have their own visibility controls (same for pads and pcb texts). This
interpretation must always match the drawing code's interpretation.
* Made TRACK::TRACK( const TRACK& ) protected to enforce use of TRACK::Copy()
2007-Sep-13 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ kicad
* Inverted the logic associated with filters. Filters now enable a file
in the project manager. The default is to ignore all files.
* The filter for *.sch files is smarter, in that it looks to display only
top level *.sch files, rather than all *.sch files.
+ Others
More beautification
2007-sept-13 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
* EDA_BaseStruct.SetType() removed.
The m_StructType member of class EDA_BaseStruct is no more modified in kicad.
Now Virtual functions can be widely used.
* The old EDA_BaseStruct.ReturnClassName() was removed.
the virtual EDA_BaseStruct.GetClass() is used instead.
+ gerbview: hotkeys Ok.
2007-Sep-13 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema & pcbnew & gerbview
A Cancel button has now been provided for the "Colors" dialog box, which also
permits it to (otherwise) be cancelled by pressing the "Esc" key; the button
whose color matches that of the color currently selected (for the layer being
edited) also has the initial focus set to it.
2007-Sep-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* Changed PcbLocateAndDisplay() to be tool specific in its search and to present
a popup menu when there are multiple items under the mouse. It is also
a framework for future enhancements.
@todo: grep for @todo and finish off those tasks.
* Introduced a formal notion of "selected item". This is done with the addition
of the WinEDA_BasePcbFrame::SetCurItem() function. So now you have to first
select an item with the left mouse button before you attempt to use the
right button popup menu. Right button no longer has an effect on the
currently selected item. The currently selected item is shown in the MsgPanel.
When none is selected, the m_Pcb is shown.
* Tweaked the OnRightClick() popup menus so that the most likely choices are
at the top.
* Added wxString BOARD_ITEM::MenuText() const and BOARD_ITEM::MenuIcon() and
both need more work, work which I will not have time to do.
2007-Sep-10 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* Searched and did not see any usage of TRACK::Copy(int), where int was other
than '1', so renamed it to TRACK::CopyList(int) and commented it out because
with int==1, this makes Copy(1) equivalent to the new Copy(void).
* Made TRACK::Copy() capable of copying SEGZONE too.
2007-sept-10 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ gerbview
Programmable hotkeys added. Fixed a compilation probleme in ansi mode (non unicode mode).
2007-Sep-8 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* Made good progress in onrightclick.cpp for multiple items under the mouse.
* Fixed some macros in macros.h so they can be followed with a semicolon and
used like simple expressions.
All changes not yet committed.
2007-sept-6 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema & pcbnew
Programmable hotkeys update.
some features are still subject to change (mainly path for config files: see 2007-aug-30 UPDATE))
The preference menu has a command to create and reread config hotkey files.
the hotkey ? lists the current hotkeys.
2007-Sep-4 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* Made GENERAL_COLLECTORS_GUIDE and GENERAL_COLLECTOR useable. They can now
serve as a fully functional replacement for PcbGeneralLocateAndDisplay(),
see DEBUG code in BOARD_ITEM* WinEDA_BasePcbFrame::PcbGeneralLocateAndDisplay().
* Made GENERAL_COLLECTOR capable of Collect()ing from a MODULE as well as a BOARD.
* pcbnew/onrightclick.cpp changed English from "Free Module" to "Unlock Module".
Next I hope to add some UI to handle multiple items under the mouse in onrightclick.cpp
2007-sept-04 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
better comments in editrack-part2 (the todo remark solved)
+ todo.txt: note about editrack-part2 modified (problem solved)
2007-Aug-31 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & gerbview
* Added TRACK::Copy() which can copy a SEGVIA or a TRACK.
* Changed export_to_pcbnew.cpp so it created a SEGVIA properly, a significant change.
Moved and changed a big block of code in export_to_pcbnew.cpp so we can
properly construct the SEGVIA(). Not tested.
* Make EDA_BaseStruct::m_StructType private so we can trap where it is being
changed. (It should never be changed after construction, see comment above
EDA_BaseStruct::SetType().)
2007-Aug-30 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
* Removed SEGVIA::IsViaOnLayer, and instead implemented an override to
virtual BOARD_ITEM::IsOnLayer() called SEGVIA::IsOnLayer().
* Tweaked TRACK::Visit() to not traverse the KICAD_T scan list and a
corresponding change to BOARD::Vist() so we can now get VIA priority
if desired. (Have to traverse m_Tracks twice, wonder if we could use
two lists: m_Tracks and a new m_Vias?)
* Changed signature of MODULE::Display_Infos( WinEDA_DrawFrame* frame ) so
it gets called virtually with any BOARD_ITEM* which is actually a MODULE*.
This was a bug.
* With virtual functions, it is now critical that the correct object type
be instantiated. This was not happening in ioascii.cpp when reading
the vias. Bug fixed.
* GENERAL_COLLECTOR getting closer to useable.
2007-aug-30 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema & pcbnew
more about programmable hotkeys.
Most existing hotkeys are programmable and displayed in popup menus or tools
Work still in progress but most features are ok.
some features are not fixed (mainly the configuration files path, which is
currently the home directory under unix systems and kicad/template under windows))
2007-Aug-29 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
Started abstract class COLLECTORS_GUIDE.
Renamed classtrc.cpp to classtrc.cpp.notused
Changed some comments in class BOARD's header to english, clarifying
linked list contents.
2007-aug-27 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ all
Display grid size in mils or mm in popup menu according to the current unit choice
2007-Aug-24 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ eeschema & pcbnew
* Removed class EDA_BaseLineStruct, which brought no behavioral advantage, only data.
Classes which were based on it got its data members added and their initializers.
* Changed type of EDA_BaseStruct::m_StructType from int to KICAD_T which is an
enum. This makes debugging easier since gdb will show the name of the
KICAD_T rather than simply a number. Added NOT_USED = -1 to KICAD_T enum for
3d which was using -1.
* More beautification using latest uncrustify and the committed uncrustify.cfg
2007-Aug-24 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
A new option has now been provided which permits Gerber files to be generated
in which the contents of the Edges Pcb layer are not also included with the
contents of each other layer.
2007-Aug-23 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ eeschema & pcbnew
* Fixed MODULE::Visit() and BOARD::Vist() so they traverse certain lists
only once and they are working nicely now.
* You can test the GENERALCOLLECTOR::Scan() code by compiling with DEBUG=1 on
the command line and enabling the stuff near line 124 in
pcbnew/controle.cpp, then watch Show( std::cout ) show the selected items in
xml format on your console. (launch pcbnew from command line.)
@todo:
The layer selection mechanism used by the collector is still inadequate, so
tomorrow I will add a new class COLLECTORS_GUIDE which can be used by a
COLLECTOR to control its operation. It adds the concept of layer
locking, even though PCBNEW does not support that in the UI yet.
2007-Aug-22 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ eeschema & pcbnew
Things are still pretty transient, should be stable a day or two:
* Fixed a filename case sensitivity problem that would show up on Linux
but probably not on Windows: bitmap/Reload.xpm needed uppercase R.
* Wedged a new class BOARD_ITEM underneath all PCB drawable classes. This is
a big change and may introduce a bug or two, but it is worth it for the
future, because we can add virtual functions there that do not impact
the entire project (since everything is derived from EDA_BaseStruct).
The corresponding class in EESCHEMA seems to be DrawPartStruct, so we had
nothing in PCBNEW like that.
BOARD_ITEM::GetLayer() and SetLayer() introduced, more functions to come.
Much of this work is geared towards making collectors.cpp's ARROWCOLLECTOR::Inspect()
very very simple, and that can be a model for future work.
* Changed min() and max() macros to MIN() and MAX() because min() and max()
are actually reserved according to the C++ standard! (and their usage prevented
the use of #include <vector>).
* Added files class_collector.h, collectors.h, and collectors.cpp.
File collectors.cpp is still unfinished.
* Started using a function and class comment style that will make sense to the
Doxygen source code documenter program.
* Beautified more un-beautified files.
2007-aug-21 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema & pcbnew
First version of programmable hotkeys by editing hotkey configuration files.
some hotkeys are not programmable (Zoom)(work in progress)
2007-Aug-21 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ administrative
Added copyright.h as a proposed copyright header for Mr. Charras's review.
Added uncrustify.cfg, the configuration file for the "uncrustify" C++ beautifier.
2007-Aug-20 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & eeschema
* Moved allowed m_Flags values from pcbnew.h, general.h, and eeschema/delete.cpp to base_struct.h
near m_Flags itself. Several of the flags values were changed. I am only
comfortable with this change if m_Flags is not written to disk anywhere,
and we need to give that some thought. If m_Flags is a memory only usage
and not saved to disk, then this change should be safe. I could not find
any case where m_Flags was being saved to disk, but I could have missed one.
The reason for the change was to consolidate into one place the allowed values
so that as new flags are allocated there is no conflict.
* Moved most all the pcbnew/affiche.cpp functions to virtual member functions of their
respective classes with the name Display_Infos().
* Moved GetEquipot() global function to BOARD::FindNet().
These changes are working towards a concise locate.cpp module, on the way
to implementing the multiple choice support. Mass edits should be slowing down
in a day or so.
2007-Aug-20 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ eeschema & pcbnew
The comments provided within postscript files now fully comply with Adobe's
Document Structuring Convention.
2007-aug-20 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema & pcbnew
modify hotkeys.cpp code (large modifications).
Added: common code in hotkeys_basic.cpp (in common) and hotkeys_basic.h (in include)
In the future, i hope hotkeys will be programmed by a config file
+ pcbnew
filename drc_dialog.prj changed to dialog_drc.prj
(according to the fulename dialog_drc.cpp and dialog_drc.h created by dialogblock from the .prj)
2007-Aug-19 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ all
* Made BASE_SCREEN::m_CurrentItem private so we can force usage of the new
SetCurItem() function, and use it to put a breakpoint on the only place
that m_CurrentItem is changed, namely in the new SetCurItem() function.
( Added new function GetCurItem() as well to class BASE_SCREEN in
drawpanel_wxstruct.h.) Using a stack trace at the breakpoint we can tell
who called it. There were in excess of 450 edits to get this done so I
had to commit it asap so other folks could get on with edits without a
merge conflict.
* Started work on the COLLECTOR class which will assist in giving a choice
in PCBNEW when there is more than one click candidate at the same mouse
or cursor coordinates. COLLECTOR not committed yet.
* More beautification.
* The mouse click and part synchronization from EESCHEMA to PCBNEW would
track fine but would not always position the PCBNEW part on screen. Now
we center it unconditionally. No change was made in the reverse direction
since that code uses the long established Find support.
2007-Aug-14 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ eeschema & pcbnew
* Added mouse click, TCP/IP socket based, part synchronization in the reverse
of how it was working, so a mouse click on a module in PCBNEW will take
EESCHEMA to the part with the same reference.
* More beautification, working with developer of uncrustify. Almost ready
to add the customized uncrustifiy configuration file to this project.
* Fixed a bug in pcbnew/tracepcb.cpp's WinEDA_PcbFrame::Trace_Pcb( wxDC* DC, int mode )
which was using a bool for the MaskLay variable, causing through hole pads
on modules on copper layer not to be shown when the copper components were
set to invisible.
2007-aug-11 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema
modify hotkeys.cpp code.
2007-Aug-10 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
Improved MODULE::FindPadOrModule().
Ran more source files through auto-beautifier.
Renamed dupltrac.cpp to dupltrac.cpp.notused.
2007-aug-10 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema
better hotkeys.cpp code.
2007-Aug-09 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
Released the new Visitor paradigm. Wrote MODULE::FindPadOrModule() using
it.
2007-aug-09 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema
Some new hotkeys (see hotkeys.cpp).
Now, the key ? display the current existing hotkeys
2007-Aug-08 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
* Renamed locate.cpp's distance() to DistanceTest() and moved it to trigo.cpp.
Pass more parameters to DistanceTest and removed globals that were used by
distance() in locate.cpp.
Moved and renamed DistanceTest function proto from protos.h to trigo.h.
* Implemented HitTest() for class_cotation, class_mire, and a few other classes
by factoring out existing code from locate.cpp. locate.cpp should operate
exactly the same as before.
* Improved or implemented the Show() function for several classes.
* Detected that the suspected class_module hit-testing bug was not real,
i.e. no bug found.
2007-aug-08 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ eeschema
bug in class_hierarchy_sheet.cpp.
+ pcbnew
small change in block commands:
rastnest was updated for each footprint, while moving footprints.
Now it is updated at the end of changes.
enhancements in block.cpp and connect.cpp
2007-Aug-07 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
* More searching work. Made HitTest() virtual. Factored out a HitTest()
function for both class_module and class_pad from existing code.
* Embellished the Show() function for several of the classes. Could be the
basis of a possible future XML export, but with the native format being
ascii already, this is of questionable value as an export.
* Discovered a long time existing bug in class_module hit-testing.
Still need to understand it. It could just be an improperly formatted module.
2007-Aug-06 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
Started sketching out a new search architecture. To learn more:
look for "INSPECTOR" text in base_struct.h.
2007-Aug-05 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew & common
* Added some conditional DEBUG code for showing the pcb object tree in
simple XML format. See class EDA_BaseStruct's new Show() function.
* Changed the function name of Locate( const wxPoint& ref_pos ) to bool HitTest(..)
in both class_text_mod and base_struct.
* More beautification and commenting.
2007-Aug-04 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
Read-ability formatting, I am playing with a C++ beautifier called "uncrustify".
I had to patch it and spent 2 days getting it configured. Patch not
sent upstream yet.
Fixed a bug in "display local ratsnest pad or module": if you had a small
module and the mouse clicked its reference text, the ratnest for
the associated module would not show. The work around was to add
support to Show_1_Ratsnest() so it could take a TYPETEXTEMODULE as
the result of the hit-testing. But I think a longer term better
solution will be to create a specific search function for this kind
of hit-testing, one which could disregard text and look only for
pads and modules.
2007-aug-02 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
Drc test now generates a DRC file report.
2007-Jul-31 UPDATE Geoff Harland <gharlandau@yahoo.com.au>
================================================================================
+ pcbnew
Drill Map and Drill Report files now list the diameters of each drill in
the selected drill unit first, and then in the other drill unit.
Drill report files also now list the tool assigned to each drill, and
the correct hole count and oval count for each drill size; the
file creation date and the selected drill unit are also listed.
2007-Jul-30 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
Some file are added (missing .prj files)
Better Drc test:
Zones can be tested.
better pad to pad test.
2007-Jul-25 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
** Some minor enhancements
+ pcbnew
In Drc diags, better (more explicit) messages
Change (and simplify) code in 'update' as well as 'insert' modules into main PCB from within the module editor,
because it had a bug (crashes when there was no footprint in pcb)
2007-June-21 UPDATE Tim Hanson <tim@hardcarve.com>
================================================================================
+ pcbnew
1. added button to 'update' as well as 'insert' modules into main PCB
from within the module editor. Made them functional, of course.
2. added control-o, control-s & control-f to pcbnew,
though I'm not perfectly happy with the implementation -- wxwidgets puts
the control-characters in alphabetical order!
2007-June-25 UPDATE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew
minor enhancement in Edit footprint dialog (more help tool tips).
better hotkey.cpp (code cleaning and info messages)
2007-June-19 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
After locking a module with 'L', update the status window with the locked
status. Side step some asserts from wxWidgets which were happening when
running compiled for debug.
2007-June-16 UPDATE Richard A Burton <richardaburton@gmail.com>
================================================================================
+ pcbnew
fix debug assert starting pcbnew with wx2.6
+ build
add install targets for resources and docs
2007-June-15 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ pcbnew
** only modules on the present layer are subject to individual module
moves, rotations, or layer swaps, with the 'M', 'G', 'R' or 'S' hotkeys.
** only unlocked modules are subject to the individual module moves,
rotations, or layer swaps, with the 'M', 'G', 'R' or 'S' hotkeys.
** implemented the 'L' hotkey to quickly lock or unlock a module,
just by hovering over it and hitting the 'L' or 'l' key. The lock is
toggled.
** Enhanced locate.cpp's Locate_Prefered_Module(BOARD * Pcb, int typeloc)
significantly, it now has a widely ranging behavior based on the
typeloc argument.
2007-June-14 UPDATE Igor Plyatov <plyatov@mail.ru>
================================================================================
+ eeschema
Added sorting by value or position in to the annotation window
(Thanks for patch to Andrey Fedorushkov).
2007-June-13 RELEASE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+All:
merging my development with svn version
+ pcbnew:
bug fix (problem in postscript generation due to the internationalization
of floating point number notation )
added tool to select layer pair and monitor active layer
+ eeschema
bug fix:
crash libedit when loading certain components (linux only)
incomplete generation of erc file list
2007-June-13 UPDATE Richard A Burton <richardaburton@gmail.com>
================================================================================
+ build:
dynamic linking by default, use make -f makefile.gtk KICAD_STATIC_LINK=1
or uncomment the bit in libs.linux for static
2007-June-11 UPDATE Richard A Burton <richardaburton@gmail.com>
================================================================================
+ build:
removed several 2 line scripts for configuring wx builds and put them in
how-to-build-kicad.txt
improved KICAD_STATIC_LINK handling so it can be overridden on the command
line e.g. "make -f makefile.gtk KICAD_STATIC_LINK=0"
2007-June-11 UPDATE Dick Hollenbeck <dick@softplc.com>
================================================================================
+ Started this change log file.
2007-June-5 UPDATE Richard A Burton <richardaburton@gmail.com>
================================================================================
+ pcbnew:
fixed 3d-display image export (blank box in image)
+ build:
fixed makefile clean targets so they don't fail if already clean
fixed wx2.6 compatibility
2007-May-25 RELEASE Jean-Pierre Charras <jean-pierre.charras@inpg.fr>
================================================================================
+ pcbnew:
bug: problem with 3D shapes.
+ Gerbview:
Better (but crude...) support to export gerber files to pcbnew.
================================================================================
End Of File