DragonProbe/README.md

# DapperMime-JTAG

(name is still WIP)

This project attempts to add Bus Pirate/...-like functionality to a number of
MCUs, mainly the Raspberry Pi Pico. It was originally based on [Dapper
Mime](https://github.com/majbthrd/DapperMime/), an SWD debugger probe implementation,
with the goal of adding JTAG support as well. However, more and more features
got added over time.

## Variants

Most support and development effort goes to the RP2040/Pico, but, due to the
projects' structure still being based on Dapper Mime's, it is relatively easy
to add support for another MCU/board. Any MCU supported by [TinyUSB
](https://github.com/hathach/tinyusb) should work. Features can also be disabled
per MCU.

Adding support for another MCU is a matter of adding another subfolder in the
`./bsp` folder, implementing the functionality (which only concerns itself with
sending commands to the hardware, protocol parsing is done by shared code),
and handling it in the `CMakeFiles.txt` file.

## Building

After initially downloading this project's code, issue the following command to download TinyUSB and CMSIS 5 code:

```
git submodule update --init --recursive
```

Compilation is done using CMake:

```
mkdir cmake-build && cd cmake-build
cmake -DBOARD=raspberry_pi_pico -DFAMILY=rp2040 -DCMAKE_BUILD_TYPE=RelWithDebInfo ..
```

`BOARD` and `FAMILY` should correspond to those used in the TinyUSB `hw` folder,
and with the folders used in `./bsp` as well.

A non-exhaustive list of possible BOARD/FAMILY combinations:

| `FAMILY` | `BOARD`            | description       | notes   |
|:-------- |:------------------ |:----------------- |:------- |
| `rp2040` |`raspberry_pi_pico` | Raspberry Pi Pico | default |

### Notes on compiling for the RP2040 Pico

If you have the Pico SDK installed on your system, and the `PICO_SDK_PATH`
environment variable is specified properly, you can omit the `--recursive` flag
in the `git submodule` invocation (to avoid many many git clones), and pass
the `-DUSE_SYSTEMWIDE_PICOSDK=On` flag to CMake, too.

Other options are:
* `-DPICO_NO_FLASH=[On|Off]`: store the binary in RAM only, useful for development.
* `-DPICO_COPY_TO_RAM=[On|Off]`: write to flash, but always run from RAM
* `-DUSE_USBCDC_FOR_STDIO=[On|Off]`: export an extra USB-CDC interface for debugging

## Usage

These microcontrollers support the following protocols:

| MCU    | SWD | JTAG | UART | SPI (flashrom) | I2C | Other stuff     |
|:------ |:---:|:----:|:----:|:-------------- |:--- |:--------------- |
| RP2040 | X   | X    | X    | X              | X   |     Planned     |

The [original repository]() (Dapper
Mime) supported only SWD and UART, and worked for the RP2040 Pico and the
STM32F072 Discovery. This fork focusses on adding more protocols, but the
author of this fork only has a Raspberry Pi Pico.

The pin mapping for the RP2040 is as follows:

| Pin number | Usage          | Usage          | Pin number |
|:---------- |:-------------- | --------------:| ----------:|
| GP0        | stdio UART TX  |                | VBUS       |
| GP1        | stdio UART RX  |                | VSYS       |
| GND        | <ground> | <ground> | GND        |
| GP2        | SWCLK/TCK      |                | 3V3 EN     |
| GP3        | SWDIO/TMS      |                | 3V3 OUT    |
| GP4        | TDI            |                | ADC VREF   |
| GP5        | TDO            |                | GP28 / ADC2|
| GND        | <ground> | <ground> | GND  / AGND|
| GP6        | nTRST          |                | GP27 / ADC1|
| GP7        | nRESET         |                | GP26 / ADC0|
| GP8        | UART TX        |                | RUN        |
| GP9        | UART RX        | (1-wire, TODO) | GP22       |
| GND        | <ground> | <ground> | GND        |
| GP10       | UART CTS       | SCL            | GP21       |
| GP11       | UART RTS       | SDA            | GP20       |
| GP12       | MISO           |                | GP19       |
| GP13       | nCS            |                | GP18       |
| GND        | <ground> | <ground> | GND        |
| GP14       | SCLK           |                | GP17       |
| GP15       | MOSI           |                | GP16       |
| <end>| <bottom> | <bottom> | <end>|

On the RP2040, two USB CDC interfaces are exposed: the first is the UART
interface, the second is for Serprog. If you have no other USB-CDC intefaces,
these will be `/dev/ttyACM0` and `/dev/ttyACM1`, respectively. If you have
enabled the `USE_USBCDC_FOR_STDIO` option, there will be a third device file.

### UART

The UART pins are for connecting to the device to be debugged, the data is
echoed back over the USB CDC interface (typically a `/dev/ttyACMx` device on
Linux). If you want to get stdio readout of this program on your computer,
connect GP0 to GP5, and GP1 to GP4, or alternatively, use the
`USE_USBCDC_FOR_STDIO` CMake flag, which adds an extra USB-CDC interface for
which stdio is used exclusively, while disabling stdio on the UART.

### SWD and JTAG debugging

In SWD mode, the pin mapping is entirely as with the standard Picoprobe setup,
as described in Chapter 5 and Appendix A of [Getting Started with Raspberry Pi
Pico](https://datasheets.raspberrypi.org/pico/getting-started-with-pico.pdf)

In JTAG mode, TCK and TMS have the same pins as SWCLK and SWDIO, respectively,
TDI and TDO are on the next two consecutive free pins.

In your OpenOCD flags, use `-f interface/cmsis-dap.cfg`. Default transport is
JTAG, if OpenOCD doesn't specify a default to the probe.

### Serprog/Flashrom

For Serprog, use the following `flashrom` options (if `/dev/ttyACM1` is the USB
serial device on your machine corresponding to the Serprog CDC interface of the
Pico):

```
flashrom -c <flashchip> -p serprog:dev=/dev/ttyACM1:115200 <rest of the read/write cmd>
```

Different serial speeds can be used, too. Serprog support is *techincally*
untested, as in it does output the correct SPI commands as seen by my logic
analyzer, but I don't have a SPI flash chip to test it on.

### I2C-Tiny-USB

The I2C-Tiny-USB functionality can be used as follows: first, load the
`i2c-dev` and `i2c-tiny-usb` modules (for now you need a patched version of the
latter, can be found in the `i2c-tiny-usb-misc/` folder in this repo). Then you
can use the I2C USB bridge as any other I2C device on your computer. For
example, the `i2cdetect`, `i2cget` and `i2cset` tools from `i2c-tools` should
all work. You can find which I2C device corresponds to the I2C-Tiny-USB, by
running `i2cdetect -l`:

```
$ sudo i2cdetect -l
[...]
i2c-1	i2c       	i915 gmbus dpb                  	I2C adapter
i2c-8	i2c       	Radeon i2c bit bus 0x95         	I2C adapter
i2c-15	i2c       	i2c-tiny-usb at bus 001 device 011	I2C adapter  # <---- !
i2c-6	i2c       	Radeon i2c bit bus 0x93         	I2C adapter
i2c-13	i2c       	AUX C/DDI C/PHY C               	I2C adapter
[...]
```

**NOTE**: I2C functionality sometimes breaks with certain USB hubs. If this is
the case, try unplugging and replugging the entire hub.

#### I2C temperature sensor emulation

If the board/MCU has a builtin temperature sensor, a fake I2C device on the bus
can optionally be enabled to use it as a Jedec JC42.2-compliant temperature
sensor (the exact sensor emulated is the Microchip MCP9808). To have it show
up in `sensors`, do the following (with `BUSNUM` the number from the above
`i2cdetect -l` output):
```
$ ./dmctl.py /dev/ttyACM1 --i2ctemp 0x18     # need to give it an address first
$ sudo modprobe jc42
$ # now tell the jc42 module that the device can be found at this address
$ echo "jc42 0x18" | sudo tee /sys/bus/i2c/devices/i2c-BUSNUM/new_device
$ sudo sensors                               # it should show up now:
jc42-i2c-BUSNUM-18
Adapter: i2c-tiny-usb at bus 001 device 032
temp1:        +23.1°C  (low  = -20.0°C)
                       (high = +75.0°C, hyst = +75.0°C)
                       (crit = +80.0°C, hyst = +80.0°C)
```

Temperature readout may be a bit higher than the ambient temperature.

### Runtime configuration

Several settings can be applied at runtime, using the `dmctl` Python script.
Settings are communicated over the Serprog USB serial port.

The currently implemented options are:
- `support`: tells you which features this implementation/board supports
- `ctsrts`: Enable/disable CTS/RTS-based hardware flow control for the UART port
- `i2ctemp`: Get or set the I2C address of the fake I2C device of the temperature
             sensor. Use 0 for getting the value, 0xff for disabling, and any
             other for setting the address. The I2C device emulated is an MCP9808.
             When setting a value, the old value is printed.

```
usage: dmctl [-h] [-v] [--ctsrts [CTSRTS]] tty

Runtime configuration control for DapperMime-JTAG

positional arguments:
  tty                Path to DapperMime-JTAG Serprog UART device

optional arguments:
  -h, --help           show this help message and exit
  -v, --verbose        Verbose logging (for this utility)
  --ctsrts [CTSRTS]    Enable or disable CTS/RTS flow control (--ctsrts [true|false])
  --i2ctemp [I2CTEMP]  Control the builtin I2C temperature controller: get (0),
                       disable (-1/0xff) or set/enable (other) the current
                       status and I2C bus address
  --support            Get list of supported/implemented functionality
```

example:

```
$ ./dmctl.py /dev/ttyACM1 --ctsrts true
```

## License

TinyUSB is licensed under the [MIT license](https://opensource.org/licenses/MIT).

ARM's CMSIS 5 code is licensed under the [Apache 2.0 license](https://opensource.org/licenses/Apache-2.0).

libco is licensed under the [ISC license](https://opensource.org/licenses/ISC)

## TODO

- [ ] A name
- [ ] A (VID and) PID, and maybe better subclass & protocol IDs for the vnd cfg itf
- [x] CMSIS-DAP JTAG implementation
- [x] Flashrom/SPI support using Serprog
  - Parallel ROM flashing support, too, by having the device switch into a
    separate mode that temporarily disables all other IO protocols
    - Not enough IO, rip.
- [x] UART with CTS/RTS flow control
  - [x] Needs configurable stuff as well, as some UART interfaces won't use this.
- [x] Debug interface to send printf stuff directly to USB, instead of having
      to use the UART interface as a loopback thing.
  - [ ] Second UART port for when stdio UART is disabled?
- [x] I2C support by emulating the I2C Tiny USB
  - [x] Expose RP2040-internal temperature ADC on I2C-over-USB bus?
  - [ ] ~~Does SMBus stuff need special treatment here?~~ ~~No.~~  Actually, some
    parts do, but, laziness.
  - [x] 10-bit I2C address support (Needs poking at the Pico SDK, as it only
        supports 7-bit ones).
- [ ] Better USB interface stuff, because I2C-Tiny-USB sucks and serprog can only
      do flash chips instead of being a real spidev. General idea can probably be
      taken from the DLN2 Linux drivers, except better (dynamic interface
      signalled in the protocol (eg. does the device actually have I2C/SPI/..?),
      dynamic I2C and SPI capabilities, add 1wire stuff, maybe yeet the GPIO bc
      it'll be used for other stuff anyway, etc.). Means a custom Linux driver but
      oh well, I2C-Tiny-USB needs patching either way.
- [ ] 1-wire using ↑
- [x] A proper interface for sending commands etc. instead of shoehorning it
      into Serprog.
  - Can probably be included in the "Better USB interface stuff".
- [ ] JTAG pinout detector
  - https://github.com/cyphunk/JTAGenum
  - https://github.com/travisgoodspeed/goodfet/blob/master/firmware/apps/jscan/jscan.c
- [ ] Host-side script that is an XVC (or hw_server) cable and communicates
      with the device to perform the JTAG commands, because Vivado no likey
      OpenOCD.
  - CMSIS-DAP interface can be used directly, see CMSIS_5/CMSIS/DoxyGen/DAP/src/dap_USB_cmds.txt
  - https://github.com/BerkeleyLab/XVC-FTDI-JTAG
  - https://www.eevblog.com/forum/fpga/xilinx-jtag-and-tcf/
  - https://git.eclipse.org/c/tcf/org.eclipse.tcf.git/plain/docs/TCF%20Linux%20Agent%20Prototype.html
  - http://www.eclipse.org/tcf/
  - https://debugmo.de/2012/02/xvcd-the-xilinx-virtual-cable-daemon/
  - https://github.com/Xilinx/XilinxVirtualCable/
  - https://github.com/derekmulcahy/xvcpi
  - OpenOCD as XVC client??
- [ ] SUMP logic analyzer mode?
  - see also [this](https://github.com/perexg/picoprobe-sump)
- [ ] FT2232 emulation mode?
  - watch out, still need a vnd cfg interface! libftdi expects the following stuff: (TODO: acquire detailed protocol description)
    - interface 0 ("A"): index 1, epin 0x02, epout 0x81
    - interface 1 ("B"): index 2, epin 0x04, epout 0x83
    - interface 2 ("C"): index 3, epin 0x06, epout 0x85
    - interface 3 ("D"): index 4, epin 0x08, epout 0x87
  - or, FX2 emulation mode??? (useful links: https://sigrok.org/wiki/Fx2lafw ; https://sigrok.org/wiki/CWAV_USBee_SX/Info )
- [ ] Mode where you can define custom PIO stuff for custom pinouts/protocols??????
  - Maybe also with code that auto-reacts to stuff from the environment?
- [ ] Facedancer implementation by connecting two picos via GPIO, one doing host
      stuff, the other device, commands being sent over GPIO to do stuff
- [ ] Maybe use the ADCs for something?
- [ ] SD/MMC/SDIO (will be a pain)
- [ ] MSP430 programming
  - https://dlbeer.co.nz/mspdebug/usb.html
  - https://github.com/dlbeer/mspdebug
  - https://www.ti.com/lit/an/slaa754/slaa754.pdf
  - https://www.ti.com/lit/ug/slau320aj/slau320aj.pdf
- [ ] AVR programming (USBavr emulation?)
  - AVR ISP is hardly used anymore
  - TPI/UPDI requires 5V levels, Pico doesn't do that :/
  - debugWIRE????
  - https://github.com/travisgoodspeed/goodfet/blob/master/firmware/apps/avr/avr.c
- [ ] PIC programming
  - https://github.com/travisgoodspeed/goodfet/tree/master/firmware/apps/pic
- iCE40 programming??
- Renesas E7-{0,1,2} programming thing????
  - Renesas tell us how this works pls
- Maybe steal other features from the Bus Pirate, [HydraBus](https://github.com/hydrabus/hydrafw) or Glasgow or so
  - 3-wire? Never seen this one in the wild
  - CAN? LIN? MOD? If I'd first be able to find a CAN device to test it with, sure