465 lines
16 KiB
C
465 lines
16 KiB
C
/*
|
|
This is *NOT* a valid CMSIS-DAP configuration; it is merely a fallback default to compile.
|
|
*/
|
|
|
|
/*
|
|
* Copyright (c) 2013-2017 ARM Limited. All rights reserved.
|
|
*
|
|
* SPDX-License-Identifier: Apache-2.0
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the License); you may
|
|
* not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an AS IS BASIS, WITHOUT
|
|
* WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*
|
|
* ----------------------------------------------------------------------
|
|
*
|
|
* $Date: 1. December 2017
|
|
* $Revision: V2.0.0
|
|
*
|
|
* Project: CMSIS-DAP Configuration
|
|
* Title: DAP_config.h CMSIS-DAP Configuration File (Template)
|
|
*
|
|
*---------------------------------------------------------------------------*/
|
|
|
|
#ifndef __DAP_CONFIG_H__
|
|
#define __DAP_CONFIG_H__
|
|
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Debug_gr CMSIS-DAP Debug Unit Information
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
Provides definitions about the hardware and configuration of the Debug Unit.
|
|
|
|
This information includes:
|
|
- Definition of Cortex-M processor parameters used in CMSIS-DAP Debug Unit.
|
|
- Debug Unit Identification strings (Vendor, Product, Serial Number).
|
|
- Debug Unit communication packet size.
|
|
- Debug Access Port supported modes and settings (JTAG/SWD and SWO).
|
|
- Optional information about a connected Target Device (for Evaluation Boards).
|
|
*/
|
|
|
|
#include "cmsis_compiler.h"
|
|
#include "bsp/board.h"
|
|
|
|
/// Processor Clock of the Cortex-M MCU used in the Debug Unit.
|
|
/// This value is used to calculate the SWD/JTAG clock speed.
|
|
#define CPU_CLOCK 100000000U ///< Specifies the CPU Clock in Hz.
|
|
|
|
/// Number of processor cycles for I/O Port write operations.
|
|
/// This value is used to calculate the SWD/JTAG clock speed that is generated with I/O
|
|
/// Port write operations in the Debug Unit by a Cortex-M MCU. Most Cortex-M processors
|
|
/// require 2 processor cycles for a I/O Port Write operation. If the Debug Unit uses
|
|
/// a Cortex-M0+ processor with high-speed peripheral I/O only 1 processor cycle might be
|
|
/// required.
|
|
#define IO_PORT_WRITE_CYCLES 2U ///< I/O Cycles: 2=default, 1=Cortex-M0+ fast I/0.
|
|
|
|
/// Indicate that Serial Wire Debug (SWD) communication mode is available at the Debug Access Port.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define DAP_SWD 1 ///< SWD Mode: 1 = available, 0 = not available.
|
|
|
|
/// Indicate that JTAG communication mode is available at the Debug Port.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define DAP_JTAG 1 ///< JTAG Mode: 1 = available, 0 = not available.
|
|
|
|
/// Configure maximum number of JTAG devices on the scan chain connected to the Debug Access Port.
|
|
/// This setting impacts the RAM requirements of the Debug Unit. Valid range is 1 .. 255.
|
|
#define DAP_JTAG_DEV_CNT 8U ///< Maximum number of JTAG devices on scan chain.
|
|
|
|
/// Default communication mode on the Debug Access Port.
|
|
/// Used for the command \ref DAP_Connect when Port Default mode is selected.
|
|
#define DAP_DEFAULT_PORT 1U ///< Default JTAG/SWJ Port Mode: 1 = SWD, 2 = JTAG.
|
|
|
|
/// Default communication speed on the Debug Access Port for SWD and JTAG mode.
|
|
/// Used to initialize the default SWD/JTAG clock frequency.
|
|
/// The command \ref DAP_SWJ_Clock can be used to overwrite this default setting.
|
|
#define DAP_DEFAULT_SWJ_CLOCK 1000000U ///< Default SWD/JTAG clock frequency in Hz.
|
|
|
|
/// Maximum Package Size for Command and Response data.
|
|
/// This configuration settings is used to optimize the communication performance with the
|
|
/// debugger and depends on the USB peripheral. Typical vales are 64 for Full-speed USB HID or WinUSB,
|
|
/// 1024 for High-speed USB HID and 512 for High-speed USB WinUSB.
|
|
#define DAP_PACKET_SIZE CFG_TUD_HID_EP_BUFSIZE ///< Specifies Packet Size in bytes.
|
|
|
|
/// Maximum Package Buffers for Command and Response data.
|
|
/// This configuration settings is used to optimize the communication performance with the
|
|
/// debugger and depends on the USB peripheral. For devices with limited RAM or USB buffer the
|
|
/// setting can be reduced (valid range is 1 .. 255).
|
|
#define DAP_PACKET_COUNT 1U ///< Specifies number of packets buffered.
|
|
|
|
/// Indicate that UART Serial Wire Output (SWO) trace is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define SWO_UART 0 ///< SWO UART: 1 = available, 0 = not available.
|
|
|
|
/// Maximum SWO UART Baudrate.
|
|
#define SWO_UART_MAX_BAUDRATE 10000000U ///< SWO UART Maximum Baudrate in Hz.
|
|
|
|
/// Indicate that Manchester Serial Wire Output (SWO) trace is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define SWO_MANCHESTER 0 ///< SWO Manchester: 1 = available, 0 = not available.
|
|
|
|
/// SWO Trace Buffer Size.
|
|
#define SWO_BUFFER_SIZE 4096U ///< SWO Trace Buffer Size in bytes (must be 2^n).
|
|
|
|
/// SWO Streaming Trace.
|
|
#define SWO_STREAM 0 ///< SWO Streaming Trace: 1 = available, 0 = not available.
|
|
|
|
/// Clock frequency of the Test Domain Timer. Timer value is returned with \ref TIMESTAMP_GET.
|
|
#define TIMESTAMP_CLOCK 0U ///< Timestamp clock in Hz (0 = timestamps not supported).
|
|
|
|
/// Debug Unit is connected to fixed Target Device.
|
|
/// The Debug Unit may be part of an evaluation board and always connected to a fixed
|
|
/// known device. In this case a Device Vendor and Device Name string is stored which
|
|
/// may be used by the debugger or IDE to configure device parameters.
|
|
#define TARGET_DEVICE_FIXED 0 ///< Target Device: 1 = known, 0 = unknown;
|
|
|
|
#if TARGET_DEVICE_FIXED
|
|
#define TARGET_DEVICE_VENDOR "ARM" ///< String indicating the Silicon Vendor
|
|
#define TARGET_DEVICE_NAME "Cortex-M4" ///< String indicating the Target Device
|
|
#endif
|
|
|
|
/** Get Vendor ID string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetVendorString (char *str) {
|
|
(void)str;
|
|
return (0U);
|
|
}
|
|
|
|
/** Get Product ID string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetProductString (char *str) {
|
|
(void)str;
|
|
return (0U);
|
|
}
|
|
|
|
/** Get Serial Number string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetSerNumString (char *str) {
|
|
(void)str;
|
|
return (0U);
|
|
}
|
|
|
|
///@}
|
|
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_PortIO_gr CMSIS-DAP Hardware I/O Pin Access
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
Standard I/O Pins of the CMSIS-DAP Hardware Debug Port support standard JTAG mode
|
|
and Serial Wire Debug (SWD) mode. In SWD mode only 2 pins are required to implement the debug
|
|
interface of a device. The following I/O Pins are provided:
|
|
|
|
JTAG I/O Pin | SWD I/O Pin | CMSIS-DAP Hardware pin mode
|
|
---------------------------- | -------------------- | ---------------------------------------------
|
|
TCK: Test Clock | SWCLK: Clock | Output Push/Pull
|
|
TMS: Test Mode Select | SWDIO: Data I/O | Output Push/Pull; Input (for receiving data)
|
|
TDI: Test Data Input | | Output Push/Pull
|
|
TDO: Test Data Output | | Input
|
|
nTRST: Test Reset (optional) | | Output Open Drain with pull-up resistor
|
|
nRESET: Device Reset | nRESET: Device Reset | Output Open Drain with pull-up resistor
|
|
|
|
|
|
DAP Hardware I/O Pin Access Functions
|
|
-------------------------------------
|
|
The various I/O Pins are accessed by functions that implement the Read, Write, Set, or Clear to
|
|
these I/O Pins.
|
|
|
|
For the SWDIO I/O Pin there are additional functions that are called in SWD I/O mode only.
|
|
This functions are provided to achieve faster I/O that is possible with some advanced GPIO
|
|
peripherals that can independently write/read a single I/O pin without affecting any other pins
|
|
of the same I/O port. The following SWDIO I/O Pin functions are provided:
|
|
- \ref PIN_SWDIO_OUT_ENABLE to enable the output mode from the DAP hardware.
|
|
- \ref PIN_SWDIO_OUT_DISABLE to enable the input mode to the DAP hardware.
|
|
- \ref PIN_SWDIO_IN to read from the SWDIO I/O pin with utmost possible speed.
|
|
- \ref PIN_SWDIO_OUT to write to the SWDIO I/O pin with utmost possible speed.
|
|
*/
|
|
|
|
|
|
// Configure DAP I/O pins ------------------------------
|
|
|
|
/** Setup JTAG I/O pins: TCK, TMS, TDI, TDO, nTRST, and nRESET.
|
|
Configures the DAP Hardware I/O pins for JTAG mode:
|
|
- TCK, TMS, TDI, nTRST, nRESET to output mode and set to high level.
|
|
- TDO to input mode.
|
|
*/
|
|
__STATIC_INLINE void PORT_JTAG_SETUP (void) {
|
|
;
|
|
}
|
|
|
|
/** Setup SWD I/O pins: SWCLK, SWDIO, and nRESET.
|
|
Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode:
|
|
- SWCLK, SWDIO, nRESET to output mode and set to default high level.
|
|
- TDI, nTRST to HighZ mode (pins are unused in SWD mode).
|
|
*/
|
|
__STATIC_INLINE void PORT_SWD_SETUP (void) {
|
|
;
|
|
}
|
|
|
|
/** Disable JTAG/SWD I/O Pins.
|
|
Disables the DAP Hardware I/O pins which configures:
|
|
- TCK/SWCLK, TMS/SWDIO, TDI, TDO, nTRST, nRESET to High-Z mode.
|
|
*/
|
|
__STATIC_INLINE void PORT_OFF (void) {
|
|
;
|
|
}
|
|
|
|
|
|
// SWCLK/TCK I/O pin -------------------------------------
|
|
|
|
/** SWCLK/TCK I/O pin: Get Input.
|
|
\return Current status of the SWCLK/TCK DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN (void) {
|
|
return (0U);
|
|
}
|
|
|
|
/** SWCLK/TCK I/O pin: Set Output to High.
|
|
Set the SWCLK/TCK DAP hardware I/O pin to high level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET (void) {
|
|
;
|
|
}
|
|
|
|
/** SWCLK/TCK I/O pin: Set Output to Low.
|
|
Set the SWCLK/TCK DAP hardware I/O pin to low level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR (void) {
|
|
;
|
|
}
|
|
|
|
|
|
// SWDIO/TMS Pin I/O --------------------------------------
|
|
|
|
/** SWDIO/TMS I/O pin: Get Input.
|
|
\return Current status of the SWDIO/TMS DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN (void) {
|
|
return (0U);
|
|
}
|
|
|
|
/** SWDIO/TMS I/O pin: Set Output to High.
|
|
Set the SWDIO/TMS DAP hardware I/O pin to high level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET (void) {
|
|
;
|
|
}
|
|
|
|
/** SWDIO/TMS I/O pin: Set Output to Low.
|
|
Set the SWDIO/TMS DAP hardware I/O pin to low level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR (void) {
|
|
;
|
|
}
|
|
|
|
/** SWDIO I/O pin: Get Input (used in SWD mode only).
|
|
\return Current status of the SWDIO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN (void) {
|
|
return (board_millis() & 1); /* pacify GCC warning */
|
|
}
|
|
|
|
/** SWDIO I/O pin: Set Output (used in SWD mode only).
|
|
\param bit Output value for the SWDIO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only).
|
|
Configure the SWDIO DAP hardware I/O pin to output mode. This function is
|
|
called prior \ref PIN_SWDIO_OUT function calls.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE (void) {
|
|
;
|
|
}
|
|
|
|
/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only).
|
|
Configure the SWDIO DAP hardware I/O pin to input mode. This function is
|
|
called prior \ref PIN_SWDIO_IN function calls.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE (void) {
|
|
;
|
|
}
|
|
|
|
|
|
// TDI Pin I/O ---------------------------------------------
|
|
|
|
/** TDI I/O pin: Get Input.
|
|
\return Current status of the TDI DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_TDI_IN (void) {
|
|
return (0U);
|
|
}
|
|
|
|
/** TDI I/O pin: Set Output.
|
|
\param bit Output value for the TDI DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_TDI_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
|
|
// TDO Pin I/O ---------------------------------------------
|
|
|
|
/** TDO I/O pin: Get Input.
|
|
\return Current status of the TDO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_TDO_IN (void) {
|
|
return (board_millis() & 1); /* pacify GCC warning */
|
|
}
|
|
|
|
|
|
// nTRST Pin I/O -------------------------------------------
|
|
|
|
/** nTRST I/O pin: Get Input.
|
|
\return Current status of the nTRST DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN (void) {
|
|
return (0U);
|
|
}
|
|
|
|
/** nTRST I/O pin: Set Output.
|
|
\param bit JTAG TRST Test Reset pin status:
|
|
- 0: issue a JTAG TRST Test Reset.
|
|
- 1: release JTAG TRST Test Reset.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_nTRST_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
// nRESET Pin I/O------------------------------------------
|
|
|
|
/** nRESET I/O pin: Get Input.
|
|
\return Current status of the nRESET DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN (void) {
|
|
return (0U);
|
|
}
|
|
|
|
/** nRESET I/O pin: Set Output.
|
|
\param bit target device hardware reset pin status:
|
|
- 0: issue a device hardware reset.
|
|
- 1: release device hardware reset.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_nRESET_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
///@}
|
|
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_LEDs_gr CMSIS-DAP Hardware Status LEDs
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
CMSIS-DAP Hardware may provide LEDs that indicate the status of the CMSIS-DAP Debug Unit.
|
|
|
|
It is recommended to provide the following LEDs for status indication:
|
|
- Connect LED: is active when the DAP hardware is connected to a debugger.
|
|
- Running LED: is active when the debugger has put the target device into running state.
|
|
*/
|
|
|
|
/** Debug Unit: Set status of Connected LED.
|
|
\param bit status of the Connect LED.
|
|
- 1: Connect LED ON: debugger is connected to CMSIS-DAP Debug Unit.
|
|
- 0: Connect LED OFF: debugger is not connected to CMSIS-DAP Debug Unit.
|
|
*/
|
|
__STATIC_INLINE void LED_CONNECTED_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
/** Debug Unit: Set status Target Running LED.
|
|
\param bit status of the Target Running LED.
|
|
- 1: Target Running LED ON: program execution in target started.
|
|
- 0: Target Running LED OFF: program execution in target stopped.
|
|
*/
|
|
__STATIC_INLINE void LED_RUNNING_OUT (uint32_t bit) {
|
|
(void)bit;
|
|
}
|
|
|
|
///@}
|
|
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Timestamp_gr CMSIS-DAP Timestamp
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
Access function for Test Domain Timer.
|
|
|
|
The value of the Test Domain Timer in the Debug Unit is returned by the function \ref TIMESTAMP_GET. By
|
|
default, the DWT timer is used. The frequency of this timer is configured with \ref TIMESTAMP_CLOCK.
|
|
|
|
*/
|
|
|
|
/** Get timestamp of Test Domain Timer.
|
|
\return Current timestamp value.
|
|
*/
|
|
__STATIC_INLINE uint32_t TIMESTAMP_GET (void) {
|
|
#if TIMESTAMP_CLOCK > 0
|
|
return (DWT->CYCCNT);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
///@}
|
|
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Initialization_gr CMSIS-DAP Initialization
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
CMSIS-DAP Hardware I/O and LED Pins are initialized with the function \ref DAP_SETUP.
|
|
*/
|
|
|
|
/** Setup of the Debug Unit I/O pins and LEDs (called when Debug Unit is initialized).
|
|
This function performs the initialization of the CMSIS-DAP Hardware I/O Pins and the
|
|
Status LEDs. In detail the operation of Hardware I/O and LED pins are enabled and set:
|
|
- I/O clock system enabled.
|
|
- all I/O pins: input buffer enabled, output pins are set to HighZ mode.
|
|
- for nTRST, nRESET a weak pull-up (if available) is enabled.
|
|
- LED output pins are enabled and LEDs are turned off.
|
|
*/
|
|
__STATIC_INLINE void DAP_SETUP (void) {
|
|
;
|
|
}
|
|
|
|
/** Reset Target Device with custom specific I/O pin or command sequence.
|
|
This function allows the optional implementation of a device specific reset sequence.
|
|
It is called when the command \ref DAP_ResetTarget and is for example required
|
|
when a device needs a time-critical unlock sequence that enables the debug port.
|
|
\return 0 = no device specific reset sequence is implemented.\n
|
|
1 = a device specific reset sequence is implemented.
|
|
*/
|
|
__STATIC_INLINE uint8_t RESET_TARGET (void) {
|
|
return (0U); // change to '1' when a device reset sequence is implemented
|
|
}
|
|
|
|
///@}
|
|
|
|
|
|
#endif /* __DAP_CONFIG_H__ */
|