sys64738
/
DragonProbe
1
0
Fork 0
Code Issues 1 Pull Requests 1 Releases Wiki Activity
DragonProbe/bsp/rp2040/DAP_config.h

582 lines
22 KiB
C
Raw Blame History

/*
* The MIT License (MIT)
*
* Copyright (c) 2021 Peter Lawrence
*
* Permission is hereby granted, free of charge, to any person obtaining a copy
* of this software and associated documentation files (the "Software"), to deal
* in the Software without restriction, including without limitation the rights
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
* copies of the Software, and to permit persons to whom the Software is
* furnished to do so, subject to the following conditions:
*
* The above copyright notice and this permission notice shall be included in
* all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
* THE SOFTWARE.
*/
/*
This DAP_config provides a CMSIS-DAP alternative to picoprobe and raspberrypi-swd.cfg
*/
#ifndef __DAP_CONFIG_H__
#define __DAP_CONFIG_H__
//**************************************************************************************************
/**
\defgroup DAP_Config_Debug_gr CMSIS-DAP Debug Unit Information
\ingroup DAP_ConfigIO_gr
@{
Provides definitions about the hardware and configuration of the Debug Unit.
This information includes:
- Definition of Cortex-M processor parameters used in CMSIS-DAP Debug Unit.
- Debug Unit Identification strings (Vendor, Product, Serial Number).
- Debug Unit communication packet size.
- Debug Access Port supported modes and settings (JTAG/SWD and SWO).
- Optional information about a connected Target Device (for Evaluation Boards).
*/
#include "cmsis_compiler.h"
#include "bsp/board.h"
#include <stdint.h>
#include <hardware/regs/resets.h>
#include <hardware/structs/resets.h>
#include <hardware/regs/sio.h>
#include <hardware/structs/sio.h>
#include <hardware/regs/pads_bank0.h>
#include <hardware/structs/padsbank0.h>
#include <hardware/regs/io_bank0.h>
#include <hardware/structs/iobank0.h>
#include <hardware/gpio.h>
#include <pico/binary_info.h>
#include "picoprobe_config.h"
#include "protos.h"
#include "unique.h"
#define PROBE_PIN_SWCLK_MASK (1UL << (PROBE_PIN_SWCLK))
#define PROBE_PIN_SWDIO_MASK (1UL << (PROBE_PIN_SWDIO))
#define PROBE_PIN_TCK_MASK (1UL << PROBE_PIN_JTAG_TCK)
#define PROBE_PIN_TMS_MASK (1UL << PROBE_PIN_JTAG_TMS)
#define PROBE_PIN_TDI_MASK (1UL << PROBE_PIN_JTAG_TDI)
#define PROBE_PIN_TDO_MASK (1UL << PROBE_PIN_JTAG_TDO)
#define PROBE_PIN_nTRST_MASK (1UL << PROBE_PIN_JTAG_nTRST)
#define PROBE_PIN_nRESET_MASK (1UL << PROBE_PIN_JTAG_nRESET)
#define PICOPROBE_LED_MASK (1UL << PICOPROBE_LED)
/// Processor Clock of the Cortex-M MCU used in the Debug Unit.
/// This value is used to calculate the SWD/JTAG clock speed.
#define CPU_CLOCK 48000000U ///< Specifies the CPU Clock in Hz.
/// Number of processor cycles for I/O Port write operations.
/// This value is used to calculate the SWD/JTAG clock speed that is generated with I/O
/// Port write operations in the Debug Unit by a Cortex-M MCU. Most Cortex-M processors
/// require 2 processor cycles for a I/O Port Write operation. If the Debug Unit uses
/// a Cortex-M0+ processor with high-speed peripheral I/O only 1 processor cycle might be
/// required.
#define IO_PORT_WRITE_CYCLES 2U ///< I/O Cycles: 2=default, 1=Cortex-M0+ fast I/0.
/// Indicate that Serial Wire Debug (SWD) communication mode is available at the Debug Access Port.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define DAP_SWD 1 ///< SWD Mode: 1 = available, 0 = not available.
/// Indicate that JTAG communication mode is available at the Debug Port.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define DAP_JTAG 1 ///< JTAG Mode: 1 = available, 0 = not available.
/// Configure maximum number of JTAG devices on the scan chain connected to the Debug Access Port.
/// This setting impacts the RAM requirements of the Debug Unit. Valid range is 1 .. 255.
#define DAP_JTAG_DEV_CNT 8U ///< Maximum number of JTAG devices on scan chain.
/// Default communication mode on the Debug Access Port.
/// Used for the command \ref DAP_Connect when Port Default mode is selected.
#define DAP_DEFAULT_PORT 2U ///< Default JTAG/SWJ Port Mode: 1 = SWD, 2 = JTAG.
/// Default communication speed on the Debug Access Port for SWD and JTAG mode.
/// Used to initialize the default SWD/JTAG clock frequency.
/// The command \ref DAP_SWJ_Clock can be used to overwrite this default setting.
#define DAP_DEFAULT_SWJ_CLOCK 1000000U ///< Default SWD/JTAG clock frequency in Hz.
/// Maximum Package Size for Command and Response data.
/// This configuration settings is used to optimize the communication performance with the
/// debugger and depends on the USB peripheral. Typical vales are 64 for Full-speed USB HID or WinUSB,
/// 1024 for High-speed USB HID and 512 for High-speed USB WinUSB.
#define DAP_PACKET_SIZE CFG_TUD_HID_EP_BUFSIZE ///< Specifies Packet Size in bytes.
/// Maximum Package Buffers for Command and Response data.
/// This configuration settings is used to optimize the communication performance with the
/// debugger and depends on the USB peripheral. For devices with limited RAM or USB buffer the
/// setting can be reduced (valid range is 1 .. 255).
#define DAP_PACKET_COUNT 1U ///< Specifies number of packets buffered.
/// Indicate that UART Serial Wire Output (SWO) trace is available.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define SWO_UART 0 ///< SWO UART: 1 = available, 0 = not available.
/// Maximum SWO UART Baudrate.
#define SWO_UART_MAX_BAUDRATE 10000000U ///< SWO UART Maximum Baudrate in Hz.
/// Indicate that Manchester Serial Wire Output (SWO) trace is available.
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
#define SWO_MANCHESTER 0 ///< SWO Manchester: 1 = available, 0 = not available.
/// SWO Trace Buffer Size.
#define SWO_BUFFER_SIZE 4096U ///< SWO Trace Buffer Size in bytes (must be 2^n).
/// SWO Streaming Trace.
#define SWO_STREAM 0 ///< SWO Streaming Trace: 1 = available, 0 = not available.
/// Clock frequency of the Test Domain Timer. Timer value is returned with \ref TIMESTAMP_GET.
#define TIMESTAMP_CLOCK 0U ///< Timestamp clock in Hz (0 = timestamps not supported).
/// Debug Unit is connected to fixed Target Device.
/// The Debug Unit may be part of an evaluation board and always connected to a fixed
/// known device. In this case a Device Vendor and Device Name string is stored which
/// may be used by the debugger or IDE to configure device parameters.
#define TARGET_DEVICE_FIXED 0 ///< Target Device: 1 = known, 0 = unknown;
#if TARGET_DEVICE_FIXED
#define TARGET_DEVICE_VENDOR "Raspberry Pi" ///< String indicating the Silicon Vendor
#define TARGET_DEVICE_NAME "Pico" ///< String indicating the Target Device
#endif
#include "DAP.h"
/** Get Vendor ID string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetVendorString (char *str) {
const static char vnd[] = INFO_MANUFACTURER;
for (size_t i = 0; i < sizeof(vnd); ++i) str[i] = vnd[i];
return sizeof(vnd)-1;
}
/** Get Product ID string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetProductString (char *str) {
const static char prd[] = INFO_PRODUCT(INFO_BOARDNAME);
for (size_t i = 0; i < sizeof(prd); ++i) str[i] = prd[i];
return sizeof(prd)-1;
}
/** Get Serial Number string.
\param str Pointer to buffer to store the string.
\return String length.
*/
__STATIC_INLINE uint8_t DAP_GetSerNumString (char *str) {
return get_unique_id_u8(str);
}
///@}
//**************************************************************************************************
/**
\defgroup DAP_Config_PortIO_gr CMSIS-DAP Hardware I/O Pin Access
\ingroup DAP_ConfigIO_gr
@{
Standard I/O Pins of the CMSIS-DAP Hardware Debug Port support standard JTAG mode
and Serial Wire Debug (SWD) mode. In SWD mode only 2 pins are required to implement the debug
interface of a device. The following I/O Pins are provided:
JTAG I/O Pin | SWD I/O Pin | CMSIS-DAP Hardware pin mode
---------------------------- | -------------------- | ---------------------------------------------
TCK: Test Clock | SWCLK: Clock | Output Push/Pull
TMS: Test Mode Select | SWDIO: Data I/O | Output Push/Pull; Input (for receiving data)
TDI: Test Data Input | | Output Push/Pull
TDO: Test Data Output | | Input
nTRST: Test Reset (optional) | | Output Open Drain with pull-up resistor
nRESET: Device Reset | nRESET: Device Reset | Output Open Drain with pull-up resistor
DAP Hardware I/O Pin Access Functions
-------------------------------------
The various I/O Pins are accessed by functions that implement the Read, Write, Set, or Clear to
these I/O Pins.
For the SWDIO I/O Pin there are additional functions that are called in SWD I/O mode only.
This functions are provided to achieve faster I/O that is possible with some advanced GPIO
peripherals that can independently write/read a single I/O pin without affecting any other pins
of the same I/O port. The following SWDIO I/O Pin functions are provided:
- \ref PIN_SWDIO_OUT_ENABLE to enable the output mode from the DAP hardware.
- \ref PIN_SWDIO_OUT_DISABLE to enable the input mode to the DAP hardware.
- \ref PIN_SWDIO_IN to read from the SWDIO I/O pin with utmost possible speed.
- \ref PIN_SWDIO_OUT to write to the SWDIO I/O pin with utmost possible speed.
*/
// Configure DAP I/O pins ------------------------------
/** Setup JTAG I/O pins: TCK, TMS, TDI, TDO, nTRST, and nRESET.
Configures the DAP Hardware I/O pins for JTAG mode:
- TCK, TMS, TDI, nTRST, nRESET to output mode and set to high level.
- TDO to input mode.
*/
__STATIC_INLINE void PORT_JTAG_SETUP (void) {
resets_hw->reset &= ~(RESETS_RESET_IO_BANK0_BITS | RESETS_RESET_PADS_BANK0_BITS);
/* set to default high level */
sio_hw->gpio_oe_set = PROBE_PIN_TCK_MASK | PROBE_PIN_TMS_MASK | PROBE_PIN_TDI_MASK | PROBE_PIN_nTRST_MASK | PROBE_PIN_nRESET_MASK;
sio_hw->gpio_set = PROBE_PIN_TCK_MASK | PROBE_PIN_TMS_MASK | PROBE_PIN_TDI_MASK | PROBE_PIN_nTRST_MASK | PROBE_PIN_nRESET_MASK;
/* TDO needs to be an input */
sio_hw->gpio_oe_clr = PROBE_PIN_TDO_MASK;
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_TCK],
PADS_BANK0_GPIO0_IE_BITS, // bits to set: input enable
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS); // bits to mask out: input enable, output disable
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_TMS],
PADS_BANK0_GPIO0_IE_BITS,
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_TDI],
PADS_BANK0_GPIO0_IE_BITS,
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_TDO],
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS, // TDO needs to have its output disabled
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_nTRST],
PADS_BANK0_GPIO0_IE_BITS,
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_JTAG_nRESET],
PADS_BANK0_GPIO0_IE_BITS,
PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
// NOTE: hiZ: ctrl = (ctrl & ~(CTRL_OEOVER_BITS)) | (GPIO_OVERRIDE_LOW << CTRL_OEOVER_LSB);
// normal == 0, low == 2
// set pin modes to general IO (SIO)
iobank0_hw->io[PROBE_PIN_JTAG_TCK].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
iobank0_hw->io[PROBE_PIN_JTAG_TMS].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
iobank0_hw->io[PROBE_PIN_JTAG_TDI].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
iobank0_hw->io[PROBE_PIN_JTAG_TDO].ctrl = (GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB)
/*| (GPIO_OVERRIDE_LOW << IO_BANK0_GPIO0_CTRL_OEOVER_LSB)*/;
iobank0_hw->io[PROBE_PIN_JTAG_nTRST].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
iobank0_hw->io[PROBE_PIN_JTAG_nRESET].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
}
/** Setup SWD I/O pins: SWCLK, SWDIO, and nRESET.
Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode:
- SWCLK, SWDIO, nRESET to output mode and set to default high level.
- TDI, nTRST to HighZ mode (pins are unused in SWD mode).
*/
__STATIC_INLINE void PORT_SWD_SETUP (void) {
resets_hw->reset &= ~(RESETS_RESET_IO_BANK0_BITS | RESETS_RESET_PADS_BANK0_BITS);
/* set to default high level */
sio_hw->gpio_oe_set = PROBE_PIN_SWCLK_MASK | PROBE_PIN_SWDIO_MASK;
sio_hw->gpio_set = PROBE_PIN_SWCLK_MASK | PROBE_PIN_SWDIO_MASK;
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_SWCLK], PADS_BANK0_GPIO0_IE_BITS, PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
hw_write_masked(&padsbank0_hw->io[PROBE_PIN_SWDIO], PADS_BANK0_GPIO0_IE_BITS, PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
iobank0_hw->io[PROBE_PIN_SWCLK].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
iobank0_hw->io[PROBE_PIN_SWDIO].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
}
/** Disable JTAG/SWD I/O Pins.
Disables the DAP Hardware I/O pins which configures:
- TCK/SWCLK, TMS/SWDIO, TDI, TDO, nTRST, nRESET to High-Z mode.
*/
__STATIC_INLINE void PORT_OFF (void) {
sio_hw->gpio_oe_clr = PROBE_PIN_SWCLK_MASK | PROBE_PIN_SWDIO_MASK
| PROBE_PIN_TDI_MASK //| PROBE_PIN_TDO_MASK
| PROBE_PIN_nTRST_MASK | PROBE_PIN_nRESET_MASK;
}
// SWCLK/TCK I/O pin -------------------------------------
/** SWCLK/TCK I/O pin: Get Input.
\return Current status of the SWCLK/TCK DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_SWCLK_MASK) >> PROBE_PIN_SWCLK;
}
/** SWCLK/TCK I/O pin: Set Output to High.
Set the SWCLK/TCK DAP hardware I/O pin to high level.
*/
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET (void) {
sio_hw->gpio_set = PROBE_PIN_SWCLK_MASK;
}
/** SWCLK/TCK I/O pin: Set Output to Low.
Set the SWCLK/TCK DAP hardware I/O pin to low level.
*/
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR (void) {
sio_hw->gpio_clr = PROBE_PIN_SWCLK_MASK;
}
// SWDIO/TMS Pin I/O --------------------------------------
/** SWDIO/TMS I/O pin: Get Input.
\return Current status of the SWDIO/TMS DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_SWDIO_MASK) >> PROBE_PIN_SWDIO;
}
/* PIN_SWDIO_TMS_SET and PIN_SWDIO_TMS_CLR are used by SWJ_Sequence */
/** SWDIO/TMS I/O pin: Set Output to High.
Set the SWDIO/TMS DAP hardware I/O pin to high level.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET (void) {
sio_hw->gpio_set = PROBE_PIN_SWDIO_MASK;
}
/** SWDIO/TMS I/O pin: Set Output to Low.
Set the SWDIO/TMS DAP hardware I/O pin to low level.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR (void) {
sio_hw->gpio_clr = PROBE_PIN_SWDIO_MASK;
}
/** SWDIO I/O pin: Get Input (used in SWD mode only).
\return Current status of the SWDIO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_SWDIO_MASK) ? 1U : 0U;
}
/** SWDIO I/O pin: Set Output (used in SWD mode only).
\param bit Output value for the SWDIO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT (uint32_t bit) {
if (bit & 1)
sio_hw->gpio_set = PROBE_PIN_SWDIO_MASK;
else
sio_hw->gpio_clr = PROBE_PIN_SWDIO_MASK;
}
/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only).
Configure the SWDIO DAP hardware I/O pin to output mode. This function is
called prior \ref PIN_SWDIO_OUT function calls.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE (void) {
sio_hw->gpio_oe_set = PROBE_PIN_SWDIO_MASK;
}
/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only).
Configure the SWDIO DAP hardware I/O pin to input mode. This function is
called prior \ref PIN_SWDIO_IN function calls.
*/
__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE (void) {
sio_hw->gpio_oe_clr = PROBE_PIN_SWDIO_MASK;
}
// TDI Pin I/O ---------------------------------------------
/** TDI I/O pin: Get Input.
\return Current status of the TDI DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_TDI_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_TDI_MASK) >> PROBE_PIN_JTAG_TDI;
}
/** TDI I/O pin: Set Output.
\param bit Output value for the TDI DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE void PIN_TDI_OUT (uint32_t bit) {
if (bit & 1)
sio_hw->gpio_set = PROBE_PIN_TDI_MASK;
else
sio_hw->gpio_clr = PROBE_PIN_TDI_MASK;
}
// TDO Pin I/O ---------------------------------------------
/** TDO I/O pin: Get Input.
\return Current status of the TDO DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_TDO_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_TDO_MASK) >> PROBE_PIN_JTAG_TDO;
}
// nTRST Pin I/O -------------------------------------------
/** nTRST I/O pin: Get Input.
\return Current status of the nTRST DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_nTRST_MASK) >> PROBE_PIN_JTAG_nTRST;
}
/** nTRST I/O pin: Set Output.
\param bit JTAG TRST Test Reset pin status:
- 0: issue a JTAG TRST Test Reset.
- 1: release JTAG TRST Test Reset.
*/
__STATIC_FORCEINLINE void PIN_nTRST_OUT (uint32_t bit) {
if (bit & 1)
sio_hw->gpio_set = PROBE_PIN_nTRST_MASK;
else
sio_hw->gpio_clr = PROBE_PIN_nTRST_MASK;
}
// nRESET Pin I/O------------------------------------------
/** nRESET I/O pin: Get Input.
\return Current status of the nRESET DAP hardware I/O pin.
*/
__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN (void) {
return (sio_hw->gpio_in & PROBE_PIN_nRESET_MASK) >> PROBE_PIN_JTAG_nRESET;
}
/** nRESET I/O pin: Set Output.
\param bit target device hardware reset pin status:
- 0: issue a device hardware reset.
- 1: release device hardware reset.
*/
__STATIC_FORCEINLINE void PIN_nRESET_OUT (uint32_t bit) {
if (bit & 1)
sio_hw->gpio_set = PROBE_PIN_nRESET_MASK;
else
sio_hw->gpio_clr = PROBE_PIN_nRESET_MASK;
}
///@}
//**************************************************************************************************
/**
\defgroup DAP_Config_LEDs_gr CMSIS-DAP Hardware Status LEDs
\ingroup DAP_ConfigIO_gr
@{
CMSIS-DAP Hardware may provide LEDs that indicate the status of the CMSIS-DAP Debug Unit.
It is recommended to provide the following LEDs for status indication:
- Connect LED: is active when the DAP hardware is connected to a debugger.
- Running LED: is active when the debugger has put the target device into running state.
*/
/** Debug Unit: Set status of Connected LED.
\param bit status of the Connect LED.
- 1: Connect LED ON: debugger is connected to CMSIS-DAP Debug Unit.
- 0: Connect LED OFF: debugger is not connected to CMSIS-DAP Debug Unit.
*/
__STATIC_INLINE void LED_CONNECTED_OUT (uint32_t bit) {
#if PICOPROBE_LED_CONNECTED
if (bit & 1)
sio_hw->gpio_set = PICOPROBE_LED_MASK;
else
sio_hw->gpio_clr = PICOPROBE_LED_MASK;
#else
(void)bit;
#endif
}
/** Debug Unit: Set status Target Running LED.
\param bit status of the Target Running LED.
- 1: Target Running LED ON: program execution in target started.
- 0: Target Running LED OFF: program execution in target stopped.
*/
__STATIC_INLINE void LED_RUNNING_OUT (uint32_t bit) {
#if PICOPROBE_LED_RUNNING
if (bit & 1)
sio_hw->gpio_set = PICOPROBE_LED_MASK;
else
sio_hw->gpio_clr = PICOPROBE_LED_MASK;
#else
(void)bit;
#endif
}
///@}
//**************************************************************************************************
/**
\defgroup DAP_Config_Timestamp_gr CMSIS-DAP Timestamp
\ingroup DAP_ConfigIO_gr
@{
Access function for Test Domain Timer.
The value of the Test Domain Timer in the Debug Unit is returned by the function \ref TIMESTAMP_GET. By
default, the DWT timer is used. The frequency of this timer is configured with \ref TIMESTAMP_CLOCK.
*/
/** Get timestamp of Test Domain Timer.
\return Current timestamp value.
*/
__STATIC_INLINE uint32_t TIMESTAMP_GET (void) {
#if TIMESTAMP_CLOCK > 0
return (DWT->CYCCNT);
#else
return 0;
#endif
}
///@}
//**************************************************************************************************
/**
\defgroup DAP_Config_Initialization_gr CMSIS-DAP Initialization
\ingroup DAP_ConfigIO_gr
@{
CMSIS-DAP Hardware I/O and LED Pins are initialized with the function \ref DAP_SETUP.
*/
/** Setup of the Debug Unit I/O pins and LEDs (called when Debug Unit is initialized).
This function performs the initialization of the CMSIS-DAP Hardware I/O Pins and the
Status LEDs. In detail the operation of Hardware I/O and LED pins are enabled and set:
- I/O clock system enabled.
- all I/O pins: input buffer enabled, output pins are set to HighZ mode.
- for nTRST, nRESET a weak pull-up (if available) is enabled.
- LED output pins are enabled and LEDs are turned off.
*/
__STATIC_INLINE void DAP_SETUP (void) {
sio_hw->gpio_oe_set = PICOPROBE_LED_MASK;
sio_hw->gpio_clr = PICOPROBE_LED_MASK;
hw_write_masked(&padsbank0_hw->io[PICOPROBE_LED], 0, PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
iobank0_hw->io[PICOPROBE_LED].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
bi_decl(bi_2pins_with_names(
PROBE_PIN_JTAG_TCK, "TCK / SWCLK",
PROBE_PIN_JTAG_TMS, "TMS / SWDIO"
));
bi_decl(bi_4pins_with_names(
PROBE_PIN_JTAG_TDI , "TDI",
PROBE_PIN_JTAG_TDO , "TDO",
PROBE_PIN_JTAG_nTRST , "nTRST",
PROBE_PIN_JTAG_nRESET, "nRESET"
));
}
/** Reset Target Device with custom specific I/O pin or command sequence.
This function allows the optional implementation of a device specific reset sequence.
It is called when the command \ref DAP_ResetTarget and is for example required
when a device needs a time-critical unlock sequence that enables the debug port.
\return 0 = no device specific reset sequence is implemented.\n
1 = a device specific reset sequence is implemented.
*/
__STATIC_INLINE uint8_t RESET_TARGET (void) {
return (0U); // change to '1' when a device reset sequence is implemented
}
///@}
#endif /* __DAP_CONFIG_H__ */
Reference in New Issue View Git Blame Copy Permalink