645 lines
25 KiB
C
645 lines
25 KiB
C
// vim: set et:
|
|
/*
|
|
* The MIT License (MIT)
|
|
*
|
|
* Copyright (c) 2021 Peter Lawrence
|
|
*
|
|
* Permission is hereby granted, free of charge, to any person obtaining a copy
|
|
* of this software and associated documentation files (the "Software"), to deal
|
|
* in the Software without restriction, including without limitation the rights
|
|
* to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
|
|
* copies of the Software, and to permit persons to whom the Software is
|
|
* furnished to do so, subject to the following conditions:
|
|
*
|
|
* The above copyright notice and this permission notice shall be included in
|
|
* all copies or substantial portions of the Software.
|
|
*
|
|
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
|
|
* IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
|
|
* FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
|
|
* AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
|
|
* LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
|
|
* OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
|
|
* THE SOFTWARE.
|
|
*/
|
|
|
|
/*
|
|
This DAP_config provides a CMSIS-DAP alternative to picoprobe and raspberrypi-swd.cfg
|
|
*/
|
|
|
|
#ifndef __DAP_CONFIG_H__
|
|
#define __DAP_CONFIG_H__
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Debug_gr CMSIS-DAP Debug Unit Information
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
Provides definitions about the hardware and configuration of the Debug Unit.
|
|
|
|
This information includes:
|
|
- Definition of Cortex-M processor parameters used in CMSIS-DAP Debug Unit.
|
|
- Debug Unit Identification strings (Vendor, Product, Serial Number).
|
|
- Debug Unit communication packet size.
|
|
- Debug Access Port supported modes and settings (JTAG/SWD and SWO).
|
|
- Optional information about a connected Target Device (for Evaluation Boards).
|
|
*/
|
|
|
|
#include <stdint.h>
|
|
|
|
#include <hardware/gpio.h>
|
|
#include <hardware/regs/io_bank0.h>
|
|
#include <hardware/regs/pads_bank0.h>
|
|
#include <hardware/regs/resets.h>
|
|
#include <hardware/regs/sio.h>
|
|
#include <hardware/structs/iobank0.h>
|
|
#include <hardware/structs/padsbank0.h>
|
|
#include <hardware/structs/resets.h>
|
|
#include <hardware/structs/sio.h>
|
|
#include <pico/binary_info.h>
|
|
|
|
#include "bsp/board.h"
|
|
#include "cmsis_compiler.h"
|
|
|
|
#include "info.h"
|
|
#include "util.h"
|
|
#include "m_default/bsp-feature.h"
|
|
#include "m_default/pinout.h"
|
|
|
|
#define PINOUT_SWCLK PINOUT_JTAG_TCK
|
|
#define PINOUT_SWDIO PINOUT_JTAG_TMS
|
|
#define PINOUT_SWO PINOUT_JTAG_TDO
|
|
|
|
#define PINOUT_SWCLK_MASK (1UL << PINOUT_SWCLK)
|
|
#define PINOUT_SWDIO_MASK (1UL << PINOUT_SWDIO)
|
|
|
|
#define PINOUT_TCK_MASK (1UL << PINOUT_JTAG_TCK)
|
|
#define PINOUT_TMS_MASK (1UL << PINOUT_JTAG_TMS)
|
|
#define PINOUT_TDI_MASK (1UL << PINOUT_JTAG_TDI)
|
|
#define PINOUT_TDO_MASK (1UL << PINOUT_JTAG_TDO)
|
|
#define PINOUT_nTRST_MASK (1UL << PINOUT_JTAG_nTRST)
|
|
#define PINOUT_nRESET_MASK (1UL << PINOUT_JTAG_nRESET)
|
|
|
|
#define PINOUT_LED_MASK (1UL << PINOUT_LED)
|
|
|
|
/// Processor Clock of the Cortex-M MCU used in the Debug Unit.
|
|
/// This value is used to calculate the SWD/JTAG clock speed.
|
|
#define CPU_CLOCK 48000000U ///< Specifies the CPU Clock in Hz.
|
|
|
|
/// Number of processor cycles for I/O Port write operations.
|
|
/// This value is used to calculate the SWD/JTAG clock speed that is generated with I/O
|
|
/// Port write operations in the Debug Unit by a Cortex-M MCU. Most Cortex-M processors
|
|
/// require 2 processor cycles for a I/O Port Write operation. If the Debug Unit uses
|
|
/// a Cortex-M0+ processor with high-speed peripheral I/O only 1 processor cycle might be
|
|
/// required.
|
|
#define IO_PORT_WRITE_CYCLES 2U ///< I/O Cycles: 2=default, 1=Cortex-M0+ fast I/0.
|
|
|
|
/// Indicate that Serial Wire Debug (SWD) communication mode is available at the Debug Access Port.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define DAP_SWD 1 ///< SWD Mode: 1 = available, 0 = not available.
|
|
|
|
/// Indicate that JTAG communication mode is available at the Debug Port.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define DAP_JTAG 1 ///< JTAG Mode: 1 = available, 0 = not available.
|
|
|
|
/// Configure maximum number of JTAG devices on the scan chain connected to the Debug Access Port.
|
|
/// This setting impacts the RAM requirements of the Debug Unit. Valid range is 1 .. 255.
|
|
#define DAP_JTAG_DEV_CNT 8U ///< Maximum number of JTAG devices on scan chain.
|
|
|
|
/// Default communication mode on the Debug Access Port.
|
|
/// Used for the command \ref DAP_Connect when Port Default mode is selected.
|
|
#define DAP_DEFAULT_PORT 2U ///< Default JTAG/SWJ Port Mode: 1 = SWD, 2 = JTAG.
|
|
|
|
/// Default communication speed on the Debug Access Port for SWD and JTAG mode.
|
|
/// Used to initialize the default SWD/JTAG clock frequency.
|
|
/// The command \ref DAP_SWJ_Clock can be used to overwrite this default setting.
|
|
#define DAP_DEFAULT_SWJ_CLOCK 1000000U ///< Default SWD/JTAG clock frequency in Hz.
|
|
|
|
/// Maximum Package Size for Command and Response data.
|
|
/// This configuration settings is used to optimize the communication performance with the
|
|
/// debugger and depends on the USB peripheral. Typical vales are 64 for Full-speed USB HID or
|
|
/// WinUSB, 1024 for High-speed USB HID and 512 for High-speed USB WinUSB.
|
|
#define DAP_PACKET_SIZE CFG_TUD_HID_EP_BUFSIZE ///< Specifies Packet Size in bytes.
|
|
|
|
/// Maximum Package Buffers for Command and Response data.
|
|
/// This configuration settings is used to optimize the communication performance with the
|
|
/// debugger and depends on the USB peripheral. For devices with limited RAM or USB buffer the
|
|
/// setting can be reduced (valid range is 1 .. 255).
|
|
#define DAP_PACKET_COUNT 1U ///< Specifies number of packets buffered.
|
|
|
|
/// Indicate that UART Serial Wire Output (SWO) trace is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define SWO_UART 1 ///< SWO UART: 1 = available, 0 = not available.
|
|
|
|
// should cause a linker error, because we're not using a hardware UART on the pico for SWO
|
|
#define SWO_UART_DRIVER 9999
|
|
|
|
/// Maximum SWO UART Baudrate.
|
|
#define SWO_UART_MAX_BAUDRATE 10000000U ///< SWO UART Maximum Baudrate in Hz.
|
|
// ^ 10 MHz
|
|
|
|
/// Indicate that Manchester Serial Wire Output (SWO) trace is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define SWO_MANCHESTER 1 ///< SWO Manchester: 1 = available, 0 = not available.
|
|
|
|
/// SWO Trace Buffer Size.
|
|
#define SWO_BUFFER_SIZE 4096U ///< SWO Trace Buffer Size in bytes (must be 2^n).
|
|
|
|
/// SWO Streaming Trace.
|
|
#define SWO_STREAM 0 ///< SWO Streaming Trace: 1 = available, 0 = not available.
|
|
|
|
/// Indicate that UART Communication Port is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#define DAP_UART 1 ///< DAP UART: 1 = available, 0 = not available.
|
|
|
|
/// USART Driver instance number for the UART Communication Port.
|
|
#define DAP_UART_DRIVER _DAPFAKE ///< USART Driver instance number (Driver_USART#).
|
|
|
|
/// UART Receive Buffer Size.
|
|
#define DAP_UART_RX_BUFFER_SIZE 64U ///< Uart Receive Buffer Size in bytes (must be 2^n).
|
|
|
|
/// UART Transmit Buffer Size.
|
|
#define DAP_UART_TX_BUFFER_SIZE 64U ///< Uart Transmit Buffer Size in bytes (must be 2^n).
|
|
|
|
/// Indicate that UART Communication via USB COM Port is available.
|
|
/// This information is returned by the command \ref DAP_Info as part of <b>Capabilities</b>.
|
|
#ifdef USE_USBCDC_FOR_STDIO
|
|
#define DAP_UART_USB_COM_PORT 1 ///< USB COM Port: 1 = available, 0 = not available.
|
|
#else
|
|
#define DAP_UART_USB_COM_PORT 0
|
|
#endif
|
|
|
|
/// Clock frequency of the Test Domain Timer. Timer value is returned with \ref TIMESTAMP_GET.
|
|
#define TIMESTAMP_CLOCK 0U ///< Timestamp clock in Hz (0 = timestamps not supported).
|
|
|
|
/// Debug Unit is connected to fixed Target Device.
|
|
/// The Debug Unit may be part of an evaluation board and always connected to a fixed
|
|
/// known device. In this case a Device Vendor and Device Name string is stored which
|
|
/// may be used by the debugger or IDE to configure device parameters.
|
|
#define TARGET_DEVICE_FIXED 0 ///< Target Device: 1 = known, 0 = unknown;
|
|
|
|
#if TARGET_DEVICE_FIXED
|
|
#define TARGET_DEVICE_VENDOR "Raspberry Pi" ///< String indicating the Silicon Vendor
|
|
#define TARGET_DEVICE_NAME "Pico" ///< String indicating the Target Device
|
|
#endif
|
|
|
|
/*#include "DAP.h"*/
|
|
|
|
/** Get Vendor ID string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetVendorString(char* str) {
|
|
static const char vnd[] = INFO_MANUFACTURER;
|
|
for (size_t i = 0; i < sizeof(vnd); ++i) str[i] = vnd[i];
|
|
return sizeof(vnd) - 1;
|
|
}
|
|
|
|
/** Get Product ID string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetProductString(char* str) {
|
|
static const char prd[] = INFO_PRODUCT(INFO_BOARDNAME);
|
|
for (size_t i = 0; i < sizeof(prd); ++i) str[i] = prd[i];
|
|
return sizeof(prd) - 1;
|
|
}
|
|
|
|
/** Get Serial Number string.
|
|
\param str Pointer to buffer to store the string.
|
|
\return String length.
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetSerNumString(char* str) {
|
|
int len = get_unique_id_u8((uint8_t*)str);
|
|
str[len] = 0;
|
|
return len;
|
|
}
|
|
|
|
/** Get Target Device Vendor string.
|
|
\param str Pointer to buffer to store the string (max 60 characters).
|
|
\return String length (including terminating NULL character) or 0 (no string).
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetTargetDeviceVendorString(char* str) {
|
|
(void)str;
|
|
return 0;
|
|
}
|
|
|
|
/** Get Target Device Name string.
|
|
\param str Pointer to buffer to store the string (max 60 characters).
|
|
\return String length (including terminating NULL character) or 0 (no string).
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetTargetDeviceNameString(char* str) {
|
|
(void)str;
|
|
return 0;
|
|
}
|
|
|
|
/** Get Target Board Vendor string.
|
|
\param str Pointer to buffer to store the string (max 60 characters).
|
|
\return String length (including terminating NULL character) or 0 (no string).
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetTargetBoardVendorString(char* str) {
|
|
(void)str;
|
|
return 0;
|
|
}
|
|
|
|
/** Get Target Board Name string.
|
|
\param str Pointer to buffer to store the string (max 60 characters).
|
|
\return String length (including terminating NULL character) or 0 (no string).
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetTargetBoardNameString(char* str) {
|
|
(void)str;
|
|
return 0;
|
|
}
|
|
|
|
/* TODO! */
|
|
/** Get Product Firmware Version string.
|
|
\param str Pointer to buffer to store the string (max 60 characters).
|
|
\return String length (including terminating NULL character) or 0 (no string).
|
|
*/
|
|
__STATIC_INLINE uint8_t DAP_GetProductFirmwareVersionString(char* str) {
|
|
(void)str;
|
|
return 0;
|
|
}
|
|
|
|
///@}
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_PortIO_gr CMSIS-DAP Hardware I/O Pin Access
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
Standard I/O Pins of the CMSIS-DAP Hardware Debug Port support standard JTAG mode
|
|
and Serial Wire Debug (SWD) mode. In SWD mode only 2 pins are required to implement the debug
|
|
interface of a device. The following I/O Pins are provided:
|
|
|
|
JTAG I/O Pin | SWD I/O Pin | CMSIS-DAP Hardware pin mode
|
|
---------------------------- | -------------------- | ---------------------------------------------
|
|
TCK: Test Clock | SWCLK: Clock | Output Push/Pull
|
|
TMS: Test Mode Select | SWDIO: Data I/O | Output Push/Pull; Input (for receiving data)
|
|
TDI: Test Data Input | | Output Push/Pull
|
|
TDO: Test Data Output | | Input
|
|
nTRST: Test Reset (optional) | | Output Open Drain with pull-up resistor
|
|
nRESET: Device Reset | nRESET: Device Reset | Output Open Drain with pull-up resistor
|
|
|
|
|
|
DAP Hardware I/O Pin Access Functions
|
|
-------------------------------------
|
|
The various I/O Pins are accessed by functions that implement the Read, Write, Set, or Clear to
|
|
these I/O Pins.
|
|
|
|
For the SWDIO I/O Pin there are additional functions that are called in SWD I/O mode only.
|
|
This functions are provided to achieve faster I/O that is possible with some advanced GPIO
|
|
peripherals that can independently write/read a single I/O pin without affecting any other pins
|
|
of the same I/O port. The following SWDIO I/O Pin functions are provided:
|
|
- \ref PIN_SWDIO_OUT_ENABLE to enable the output mode from the DAP hardware.
|
|
- \ref PIN_SWDIO_OUT_DISABLE to enable the input mode to the DAP hardware.
|
|
- \ref PIN_SWDIO_IN to read from the SWDIO I/O pin with utmost possible speed.
|
|
- \ref PIN_SWDIO_OUT to write to the SWDIO I/O pin with utmost possible speed.
|
|
*/
|
|
|
|
// Configure DAP I/O pins ------------------------------
|
|
|
|
/** Setup JTAG I/O pins: TCK, TMS, TDI, TDO, nTRST, and nRESET.
|
|
Configures the DAP Hardware I/O pins for JTAG mode:
|
|
- TCK, TMS, TDI, nTRST, nRESET to output mode and set to high level.
|
|
- TDO to input mode.
|
|
*/
|
|
void PORT_JTAG_SETUP(void);
|
|
//__STATIC_INLINE void PORT_JTAG_SETUP(void) {
|
|
// resets_hw->reset &= ~(RESETS_RESET_IO_BANK0_BITS | RESETS_RESET_PADS_BANK0_BITS);
|
|
//
|
|
// /* set to default high level */
|
|
// sio_hw->gpio_oe_set = PINOUT_TCK_MASK | PINOUT_TMS_MASK | PINOUT_TDI_MASK | PINOUT_nTRST_MASK |
|
|
// PINOUT_nRESET_MASK;
|
|
// sio_hw->gpio_set = PINOUT_TCK_MASK | PINOUT_TMS_MASK | PINOUT_TDI_MASK | PINOUT_nTRST_MASK |
|
|
// PINOUT_nRESET_MASK;
|
|
// /* TDO needs to be an input */
|
|
// sio_hw->gpio_oe_clr = PINOUT_TDO_MASK;
|
|
//
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_TCK],
|
|
// PADS_BANK0_GPIO0_IE_BITS, // bits to set: input enable
|
|
// PADS_BANK0_GPIO0_IE_BITS |
|
|
// PADS_BANK0_GPIO0_OD_BITS); // bits to mask out: input enable, output disable
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_TMS], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_TDI], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_TDO],
|
|
// PADS_BANK0_GPIO0_IE_BITS |
|
|
// PADS_BANK0_GPIO0_OD_BITS, // TDO needs to have its output disabled
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_nTRST], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_JTAG_nRESET], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
//
|
|
// // NOTE: hiZ: ctrl = (ctrl & ~(CTRL_OEOVER_BITS)) | (GPIO_OVERRIDE_LOW << CTRL_OEOVER_LSB);
|
|
// // normal == 0, low == 2
|
|
//
|
|
// // set pin modes to general IO (SIO)
|
|
// iobank0_hw->io[PINOUT_JTAG_TCK].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
// iobank0_hw->io[PINOUT_JTAG_TMS].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
// iobank0_hw->io[PINOUT_JTAG_TDI].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
// iobank0_hw->io[PINOUT_JTAG_TDO].ctrl = (GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB)
|
|
// /*| (GPIO_OVERRIDE_LOW << IO_BANK0_GPIO0_CTRL_OEOVER_LSB)*/;
|
|
// iobank0_hw->io[PINOUT_JTAG_nTRST].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
// iobank0_hw->io[PINOUT_JTAG_nRESET].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
//}
|
|
|
|
/** Setup SWD I/O pins: SWCLK, SWDIO, and nRESET.
|
|
Configures the DAP Hardware I/O pins for Serial Wire Debug (SWD) mode:
|
|
- SWCLK, SWDIO, nRESET to output mode and set to default high level.
|
|
- TDI, nTRST to HighZ mode (pins are unused in SWD mode).
|
|
*/
|
|
void PORT_SWD_SETUP(void);
|
|
//__STATIC_INLINE void PORT_SWD_SETUP(void) {
|
|
// resets_hw->reset &= ~(RESETS_RESET_IO_BANK0_BITS | RESETS_RESET_PADS_BANK0_BITS);
|
|
//
|
|
// /* set to default high level */
|
|
// sio_hw->gpio_oe_set = PINOUT_SWCLK_MASK | PINOUT_SWDIO_MASK;
|
|
// sio_hw->gpio_set = PINOUT_SWCLK_MASK | PINOUT_SWDIO_MASK;
|
|
//
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_SWCLK], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// hw_write_masked(&padsbank0_hw->io[PINOUT_SWDIO], PADS_BANK0_GPIO0_IE_BITS,
|
|
// PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
// iobank0_hw->io[PINOUT_SWCLK].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
// iobank0_hw->io[PINOUT_SWDIO].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
//}
|
|
|
|
/** Disable JTAG/SWD I/O Pins.
|
|
Disables the DAP Hardware I/O pins which configures:
|
|
- TCK/SWCLK, TMS/SWDIO, TDI, TDO, nTRST, nRESET to High-Z mode.
|
|
*/
|
|
void PORT_OFF(void);
|
|
/*__STATIC_INLINE void PORT_OFF(void) {
|
|
sio_hw->gpio_oe_clr = PINOUT_SWCLK_MASK | PINOUT_SWDIO_MASK |
|
|
PINOUT_TDI_MASK //| PINOUT_TDO_MASK
|
|
| PINOUT_nTRST_MASK | PINOUT_nRESET_MASK;
|
|
}*/
|
|
|
|
// SWCLK/TCK I/O pin -------------------------------------
|
|
|
|
/** SWCLK/TCK I/O pin: Get Input.
|
|
\return Current status of the SWCLK/TCK DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWCLK_TCK_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_SWCLK_MASK) >> PINOUT_SWCLK;
|
|
}
|
|
|
|
/** SWCLK/TCK I/O pin: Set Output to High.
|
|
Set the SWCLK/TCK DAP hardware I/O pin to high level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_SET(void) { sio_hw->gpio_set = PINOUT_SWCLK_MASK; }
|
|
|
|
/** SWCLK/TCK I/O pin: Set Output to Low.
|
|
Set the SWCLK/TCK DAP hardware I/O pin to low level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWCLK_TCK_CLR(void) { sio_hw->gpio_clr = PINOUT_SWCLK_MASK; }
|
|
|
|
// SWDIO/TMS Pin I/O --------------------------------------
|
|
|
|
/** SWDIO/TMS I/O pin: Get Input.
|
|
\return Current status of the SWDIO/TMS DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_TMS_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_SWDIO_MASK) >> PINOUT_SWDIO;
|
|
}
|
|
|
|
/* PIN_SWDIO_TMS_SET and PIN_SWDIO_TMS_CLR are used by SWJ_Sequence */
|
|
|
|
/** SWDIO/TMS I/O pin: Set Output to High.
|
|
Set the SWDIO/TMS DAP hardware I/O pin to high level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_SET(void) { sio_hw->gpio_set = PINOUT_SWDIO_MASK; }
|
|
|
|
/** SWDIO/TMS I/O pin: Set Output to Low.
|
|
Set the SWDIO/TMS DAP hardware I/O pin to low level.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_TMS_CLR(void) { sio_hw->gpio_clr = PINOUT_SWDIO_MASK; }
|
|
|
|
/** SWDIO I/O pin: Get Input (used in SWD mode only).
|
|
\return Current status of the SWDIO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_SWDIO_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_SWDIO_MASK) ? 1U : 0U;
|
|
}
|
|
|
|
/** SWDIO I/O pin: Set Output (used in SWD mode only).
|
|
\param bit Output value for the SWDIO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_SWDIO_OUT(uint32_t bit) {
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_SWDIO_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_SWDIO_MASK;
|
|
}
|
|
|
|
/** SWDIO I/O pin: Switch to Output mode (used in SWD mode only).
|
|
Configure the SWDIO DAP hardware I/O pin to output mode. This function is
|
|
called prior \ref PIN_SWDIO_OUT function calls.
|
|
*/
|
|
//__STATIC_FORCEINLINE void PIN_SWDIO_OUT_ENABLE(void) { sio_hw->gpio_oe_set = PINOUT_SWDIO_MASK; }
|
|
void PIN_SWDIO_OUT_ENABLE(void);
|
|
|
|
/** SWDIO I/O pin: Switch to Input mode (used in SWD mode only).
|
|
Configure the SWDIO DAP hardware I/O pin to input mode. This function is
|
|
called prior \ref PIN_SWDIO_IN function calls.
|
|
*/
|
|
//__STATIC_FORCEINLINE void PIN_SWDIO_OUT_DISABLE(void) { sio_hw->gpio_oe_clr = PINOUT_SWDIO_MASK; }
|
|
void PIN_SWDIO_OUT_DISABLE(void);
|
|
|
|
// TDI Pin I/O ---------------------------------------------
|
|
|
|
/** TDI I/O pin: Get Input.
|
|
\return Current status of the TDI DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_TDI_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_TDI_MASK) >> PINOUT_JTAG_TDI;
|
|
}
|
|
|
|
/** TDI I/O pin: Set Output.
|
|
\param bit Output value for the TDI DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_TDI_OUT(uint32_t bit) {
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_TDI_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_TDI_MASK;
|
|
}
|
|
|
|
// TDO Pin I/O ---------------------------------------------
|
|
|
|
/** TDO I/O pin: Get Input.
|
|
\return Current status of the TDO DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_TDO_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_TDO_MASK) >> PINOUT_JTAG_TDO;
|
|
}
|
|
|
|
// nTRST Pin I/O -------------------------------------------
|
|
|
|
/** nTRST I/O pin: Get Input.
|
|
\return Current status of the nTRST DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_nTRST_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_nTRST_MASK) >> PINOUT_JTAG_nTRST;
|
|
}
|
|
|
|
/** nTRST I/O pin: Set Output.
|
|
\param bit JTAG TRST Test Reset pin status:
|
|
- 0: issue a JTAG TRST Test Reset.
|
|
- 1: release JTAG TRST Test Reset.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_nTRST_OUT(uint32_t bit) {
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_nTRST_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_nTRST_MASK;
|
|
}
|
|
|
|
// nRESET Pin I/O------------------------------------------
|
|
|
|
/** nRESET I/O pin: Get Input.
|
|
\return Current status of the nRESET DAP hardware I/O pin.
|
|
*/
|
|
__STATIC_FORCEINLINE uint32_t PIN_nRESET_IN(void) {
|
|
return (sio_hw->gpio_in & PINOUT_nRESET_MASK) >> PINOUT_JTAG_nRESET;
|
|
}
|
|
|
|
/** nRESET I/O pin: Set Output.
|
|
\param bit target device hardware reset pin status:
|
|
- 0: issue a device hardware reset.
|
|
- 1: release device hardware reset.
|
|
*/
|
|
__STATIC_FORCEINLINE void PIN_nRESET_OUT(uint32_t bit) {
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_nRESET_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_nRESET_MASK;
|
|
}
|
|
|
|
///@}
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_LEDs_gr CMSIS-DAP Hardware Status LEDs
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
CMSIS-DAP Hardware may provide LEDs that indicate the status of the CMSIS-DAP Debug Unit.
|
|
|
|
It is recommended to provide the following LEDs for status indication:
|
|
- Connect LED: is active when the DAP hardware is connected to a debugger.
|
|
- Running LED: is active when the debugger has put the target device into running state.
|
|
*/
|
|
|
|
/** Debug Unit: Set status of Connected LED.
|
|
\param bit status of the Connect LED.
|
|
- 1: Connect LED ON: debugger is connected to CMSIS-DAP Debug Unit.
|
|
- 0: Connect LED OFF: debugger is not connected to CMSIS-DAP Debug Unit.
|
|
*/
|
|
__STATIC_INLINE void LED_CONNECTED_OUT(uint32_t bit) {
|
|
#if PINOUT_LED_CONNECTED
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_LED_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_LED_MASK;
|
|
#else
|
|
(void)bit;
|
|
#endif
|
|
}
|
|
|
|
/** Debug Unit: Set status Target Running LED.
|
|
\param bit status of the Target Running LED.
|
|
- 1: Target Running LED ON: program execution in target started.
|
|
- 0: Target Running LED OFF: program execution in target stopped.
|
|
*/
|
|
__STATIC_INLINE void LED_RUNNING_OUT(uint32_t bit) {
|
|
#if PINOUT_LED_RUNNING
|
|
if (bit & 1)
|
|
sio_hw->gpio_set = PINOUT_LED_MASK;
|
|
else
|
|
sio_hw->gpio_clr = PINOUT_LED_MASK;
|
|
#else
|
|
(void)bit;
|
|
#endif
|
|
}
|
|
|
|
///@}
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Timestamp_gr CMSIS-DAP Timestamp
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
Access function for Test Domain Timer.
|
|
|
|
The value of the Test Domain Timer in the Debug Unit is returned by the function \ref TIMESTAMP_GET.
|
|
By default, the DWT timer is used. The frequency of this timer is configured with \ref
|
|
TIMESTAMP_CLOCK.
|
|
|
|
*/
|
|
|
|
/** Get timestamp of Test Domain Timer.
|
|
\return Current timestamp value.
|
|
*/
|
|
__STATIC_INLINE uint32_t TIMESTAMP_GET(void) {
|
|
#if TIMESTAMP_CLOCK > 0
|
|
return (DWT->CYCCNT);
|
|
#else
|
|
return 0;
|
|
#endif
|
|
}
|
|
|
|
///@}
|
|
|
|
//**************************************************************************************************
|
|
/**
|
|
\defgroup DAP_Config_Initialization_gr CMSIS-DAP Initialization
|
|
\ingroup DAP_ConfigIO_gr
|
|
@{
|
|
|
|
CMSIS-DAP Hardware I/O and LED Pins are initialized with the function \ref DAP_SETUP.
|
|
*/
|
|
|
|
/** Setup of the Debug Unit I/O pins and LEDs (called when Debug Unit is initialized).
|
|
This function performs the initialization of the CMSIS-DAP Hardware I/O Pins and the
|
|
Status LEDs. In detail the operation of Hardware I/O and LED pins are enabled and set:
|
|
- I/O clock system enabled.
|
|
- all I/O pins: input buffer enabled, output pins are set to HighZ mode.
|
|
- for nTRST, nRESET a weak pull-up (if available) is enabled.
|
|
- LED output pins are enabled and LEDs are turned off.
|
|
*/
|
|
__STATIC_INLINE void DAP_SETUP(void) {
|
|
sio_hw->gpio_oe_set = PINOUT_LED_MASK;
|
|
sio_hw->gpio_clr = PINOUT_LED_MASK;
|
|
|
|
hw_write_masked(
|
|
&padsbank0_hw->io[PINOUT_LED], 0, PADS_BANK0_GPIO0_IE_BITS | PADS_BANK0_GPIO0_OD_BITS);
|
|
iobank0_hw->io[PINOUT_LED].ctrl = GPIO_FUNC_SIO << IO_BANK0_GPIO0_CTRL_FUNCSEL_LSB;
|
|
|
|
bi_decl(bi_2pins_with_names(PINOUT_JTAG_TCK, "TCK / SWCLK", PINOUT_JTAG_TMS, "TMS / SWDIO"));
|
|
bi_decl(bi_4pins_with_names(PINOUT_JTAG_TDI, "TDI", PINOUT_JTAG_TDO, "TDO", PINOUT_JTAG_nTRST,
|
|
"nTRST", PINOUT_JTAG_nRESET, "nRESET"));
|
|
}
|
|
|
|
/** Reset Target Device with custom specific I/O pin or command sequence.
|
|
This function allows the optional implementation of a device specific reset sequence.
|
|
It is called when the command \ref DAP_ResetTarget and is for example required
|
|
when a device needs a time-critical unlock sequence that enables the debug port.
|
|
\return 0 = no device specific reset sequence is implemented.\n
|
|
1 = a device specific reset sequence is implemented.
|
|
*/
|
|
__STATIC_INLINE uint8_t RESET_TARGET(void) {
|
|
return (0U); // change to '1' when a device reset sequence is implemented
|
|
}
|
|
|
|
///@}
|
|
|
|
extern int swdsm, swdoffset, jtagsm, jtagoffset;
|
|
|
|
#endif /* __DAP_CONFIG_H__ */
|
|
|