272 lines
11 KiB
Markdown
272 lines
11 KiB
Markdown
|
# Using RTT
|
||
|
|
|
||
|
|
When debugging arm processors, there are three ways for the target to print debug messages on the host: Semihosting, Serial Wire Output SWO, and Real-Time Transfer RTT.
|
||
|
|
|
||
|
|
[Black Magic Probe](https://github.com/blacksphere/blackmagic) (BMP) is an open source debugger probe that already implements Semihosting and Single Wire Output. This patch adds Real-Time Transfer RTT output to usb serial port.
|
||
|
|
|
||
|
|
- RTT is implemented, not as a user program, but as a serial port device. To read RTT output, use a terminal emulator and connect to the serial port.
|
||
|
|
|
||
|
|
- A novel way to detect RTT automatically, fast and convenient.
|
||
|
|
|
||
|
|
## Use
|
||
|
|
This example uses linux as operating system. For Windows and MacOS see the *Operating Systems* section.
|
||
|
|
|
||
|
|
In one window open a terminal emulator (minicom, putty) and connect to the usb uart:
|
||
|
|
```
|
||
|
|
$ minicom -c on -D /dev/ttyBmpTarg
|
||
|
|
```
|
||
|
|
|
||
|
|
In another window open a debugger:
|
||
|
|
```
|
||
|
|
$ gdb
|
||
|
|
(gdb) target extended-remote /dev/ttyBmpGdb
|
||
|
|
(gdb) monitor swdp_scan
|
||
|
|
(gdb) attach 1
|
||
|
|
(gdb) monitor rtt
|
||
|
|
(gdb) run
|
||
|
|
^C
|
||
|
|
(gdb) monitor rtt status
|
||
|
|
rtt: on found: yes ident: off halt: off channels: auto 0 1 3
|
||
|
|
max poll ms: 256 min poll ms: 8 max errs: 10
|
||
|
|
```
|
||
|
|
|
||
|
|
The terminal emulator displays RTT output from the target,
|
||
|
|
and characters typed in the terminal emulator are sent via RTT to the target.
|
||
|
|
|
||
|
|
|
||
|
|
## gdb commands
|
||
|
|
|
||
|
|
The following new gdb commands are available:
|
||
|
|
|
||
|
|
- ``monitor rtt``
|
||
|
|
|
||
|
|
switch rtt on
|
||
|
|
|
||
|
|
- ``monitor rtt enable``
|
||
|
|
|
||
|
|
switch rtt on
|
||
|
|
|
||
|
|
- ``monitor rtt disable``
|
||
|
|
|
||
|
|
switch rtt off
|
||
|
|
|
||
|
|
- ``monitor rtt poll `` max_poll_ms min_poll_ms max_errs
|
||
|
|
|
||
|
|
sets maximum time between polls, minimum time between polls, and the maximum number of errors before RTT disconnects from the target. Times in milliseconds. It is best if max_poll_ms/min_poll_ms is a power of two. As an example, if you wish to check for RTT output between once per second to eight times per second: ``monitor rtt poll 1000 125 10``.
|
||
|
|
|
||
|
|
- ``monitor rtt status``
|
||
|
|
|
||
|
|
show status.
|
||
|
|
|
||
|
|
rtt|found|state
|
||
|
|
---|---|---
|
||
|
|
rtt: off|found: no|rtt inactive
|
||
|
|
rtt: on|found: no|searching for rtt control block
|
||
|
|
rtt: on|found: yes|rtt active
|
||
|
|
rtt: off|found: yes|corrupt rtt control block, or target memory access error
|
||
|
|
|
||
|
|
A status of `rtt: on found: no` indicates bmp is still searching for the rtt control block in target ram, but has not found anything yet. A status of `rtt: on found: yes` indicates the control block has been found and rtt is active.
|
||
|
|
|
||
|
|
- ``monitor rtt channel``
|
||
|
|
|
||
|
|
enables the first two output channels, and the first input channel. (default)
|
||
|
|
|
||
|
|
- ``monitor rtt channel number...``
|
||
|
|
|
||
|
|
enables the given RTT channel numbers. Channels are numbers from 0 to 15, inclusive. Eg. ``monitor rtt channel 0 1 4`` to enable channels 0, 1, and 4.
|
||
|
|
|
||
|
|
- ``monitor rtt ident string``
|
||
|
|
|
||
|
|
sets RTT ident to *string*. If *string* contains a space, replace the space with an underscore _. Setting ident string is optional, RTT works fine without.
|
||
|
|
|
||
|
|
- ``monitor rtt ident``
|
||
|
|
|
||
|
|
clears ident string. (default)
|
||
|
|
|
||
|
|
- ``monitor rtt cblock``
|
||
|
|
|
||
|
|
shows rtt control block data, and which channels are enabled. This is an example control block:
|
||
|
|
|
||
|
|
```
|
||
|
|
(gdb) mon rtt cb
|
||
|
|
cbaddr: 0x200000a0
|
||
|
|
ch ena cfg i/o buf@ size head@ tail@ flg
|
||
|
|
0 y y out 0x20000148 1024 0x200000c4 0x200000c8 2
|
||
|
|
1 y n out 0x00000000 0 0x200000dc 0x200000e0 0
|
||
|
|
2 n n out 0x00000000 0 0x200000f4 0x200000f8 0
|
||
|
|
3 y y in 0x20000548 16 0x2000010c 0x20000110 0
|
||
|
|
4 n n in 0x00000000 0 0x20000124 0x20000128 0
|
||
|
|
5 n n in 0x00000000 0 0x2000013c 0x20000140 0
|
||
|
|
6 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
7 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
8 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
9 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
10 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
11 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
12 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
13 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
14 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
15 n n in 0x00000000 0 0x00000000 0x00000000 0
|
||
|
|
```
|
||
|
|
|
||
|
|
Channels are listed, one channel per line. The columns are: channel, enabled, configured, input/output, buffer address, buffer size, address of head pointer, address of tail pointer, flag. Each channel is a circular buffer with head and tail pointer.
|
||
|
|
|
||
|
|
Note the columns `ena` for enabled, `cfg` for configured.
|
||
|
|
|
||
|
|
Configured channels have a non-zero buffer address and non-zero size. Configured channels are marked yes `y` in the column `cfg` . What channels are configured depends upon target software.
|
||
|
|
|
||
|
|
Channels the user wants to see are marked yes `y` in the column enabled `ena`. The user can change which channels are shown with the `monitor rtt channel` command.
|
||
|
|
|
||
|
|
Output channels are displayed, and Input channels receive keyboard input, if they are marked yes in both *enabled* and *configured*.
|
||
|
|
|
||
|
|
The control block is cached for speed. In an interrupted program, `monitor rtt` will force a reload of the control block when the program continues.
|
||
|
|
|
||
|
|
## Identifier string
|
||
|
|
It is possible to set an RTT identifier string.
|
||
|
|
As an example, if the RTT identifier is "IDENT STR":
|
||
|
|
```
|
||
|
|
$ gdb
|
||
|
|
(gdb) target extended-remote /dev/ttyBmpGdb
|
||
|
|
(gdb) monitor swdp_scan
|
||
|
|
(gdb) attach 1
|
||
|
|
(gdb) monitor rtt ident IDENT_STR
|
||
|
|
(gdb) monitor rtt
|
||
|
|
(gdb) run
|
||
|
|
^C
|
||
|
|
(gdb) monitor rtt status
|
||
|
|
rtt: on found: yes ident: "IDENT STR" halt: off channels: auto 0 1 3
|
||
|
|
max poll ms: 256 min poll ms: 8 max errs: 10
|
||
|
|
```
|
||
|
|
Note replacing space with underscore _ in *monitor rtt ident*.
|
||
|
|
|
||
|
|
Setting an identifier string is optional. RTT gives the same output at the same speed, with or without specifying identifier string.
|
||
|
|
|
||
|
|
## Operating systems
|
||
|
|
|
||
|
|
[Configuration](https://github.com/blacksphere/blackmagic/wiki/Getting-Started) instructions for windows, linux and macos.
|
||
|
|
|
||
|
|
### Windows
|
||
|
|
|
||
|
|
After configuration, Black Magic Probe shows up in Windows as two _USB Serial (CDC)_ ports.
|
||
|
|
|
||
|
|
Connect arm-none-eabi-gdb, the gnu debugger for arm processors, to the lower numbered of the two COM ports. Connect an ansi terminal emulator to the higher numbered of the two COM ports.
|
||
|
|
|
||
|
|
Sample gdb session:
|
||
|
|
```
|
||
|
|
(gdb) target extended-remote COM3
|
||
|
|
(gdb) monitor swdp_scan
|
||
|
|
(gdb) attach 1
|
||
|
|
(gdb) monitor rtt
|
||
|
|
(gdb) run
|
||
|
|
```
|
||
|
|
|
||
|
|
For COM port COM10 and higher, add the prefix `\\.\`, e.g.
|
||
|
|
```
|
||
|
|
target extended-remote \\.\COM10
|
||
|
|
```
|
||
|
|
|
||
|
|
Target RTT output will appear in the terminal, and what you type in the terminal will be sent to the RTT input of the target.
|
||
|
|
|
||
|
|
### linux
|
||
|
|
On linux, install [udev rules](https://github.com/blacksphere/blackmagic/blob/master/driver/99-blackmagic.rules). Disconnect and re-connect the BMP. Check the device shows up in /dev/ :
|
||
|
|
```
|
||
|
|
$ ls -l /dev/ttyBmp*
|
||
|
|
lrwxrwxrwx 1 root root 7 Dec 13 07:29 /dev/ttyBmpGdb -> ttyACM0
|
||
|
|
lrwxrwxrwx 1 root root 7 Dec 13 07:29 /dev/ttyBmpTarg -> ttyACM2
|
||
|
|
```
|
||
|
|
Connect terminal emulator to /dev/ttyBmpTarg and gdb to /dev/ttyBmpGdb .
|
||
|
|
|
||
|
|
In one window:
|
||
|
|
```
|
||
|
|
minicom -c on -D /dev/ttyBmpTarg
|
||
|
|
```
|
||
|
|
In another window :
|
||
|
|
```
|
||
|
|
gdb
|
||
|
|
(gdb) target extended-remote /dev/ttyBmpGdb
|
||
|
|
(gdb) monitor swdp_scan
|
||
|
|
(gdb) attach 1
|
||
|
|
(gdb) monitor rtt
|
||
|
|
(gdb) run
|
||
|
|
```
|
||
|
|
|
||
|
|
### MacOS
|
||
|
|
|
||
|
|
On MacOS the tty devices have different names than on linux. On connecting blackmagic to the computer 4 devices are created, 2 'tty' and 2 'cu' devices. Gdb connects to the first cu device (e.g.: `target extended-remote /dev/cu.usbmodemDDCEC9EC1`), while RTT is connected to the second tty device (`minicom -c on -D /dev/tty.usbmodemDDCEC9EC3`). In full:
|
||
|
|
|
||
|
|
In one Terminal window, connect a terminal emulator to /dev/tty.usbmodemDDCEC9EC3 :
|
||
|
|
|
||
|
|
```
|
||
|
|
minicom -c on -D /dev/tty.usbmodemDDCEC9EC3
|
||
|
|
```
|
||
|
|
In another Terminal window, connect gdb to /dev/cu.usbmodemDDCEC9EC1 :
|
||
|
|
```
|
||
|
|
gdb
|
||
|
|
(gdb) target extended-remote /dev/cu.usbmodemDDCEC9EC1
|
||
|
|
(gdb) monitor swdp_scan
|
||
|
|
(gdb) attach 1
|
||
|
|
(gdb) monitor rtt
|
||
|
|
(gdb) run
|
||
|
|
```
|
||
|
|
RTT input/output is in the window running _minicom_.
|
||
|
|
|
||
|
|
## Notes
|
||
|
|
|
||
|
|
- Design goal was smallest, simplest implementation that has good practical use.
|
||
|
|
|
||
|
|
- RTT code size is 3.5 kbyte - the whole debugger 110 kbyte.
|
||
|
|
|
||
|
|
- Because RTT is implemented as a serial port device, there is no need to write and maintain software for different host operating systems. A serial port works everywhere - linux, windows and mac. You can even use an Android mobile phone as RTT terminal.
|
||
|
|
|
||
|
|
- Because polling occurs between debugger probe and target, the load on the host is small. There is no constant usb traffic, there are no real-time requirements on the host.
|
||
|
|
|
||
|
|
- RTT polling frequency is adaptive and goes up and down with RTT activity. Use *monitor rtt poll* to balance response speed and target load for your use.
|
||
|
|
|
||
|
|
- Detects RTT automatically, very convenient.
|
||
|
|
|
||
|
|
- When using RTT as a terminal, sending data from host to target, you may need to change local echo, carriage return and/or line feed settings in your terminal emulator.
|
||
|
|
|
||
|
|
- Architectures such as risc-v may not allow the debugger access to target memory while the target is running. As a workaround, on these architectures RTT briefly halts the target during polling. If the target is halted during polling, `monitor rtt status` shows `halt: on`.
|
||
|
|
|
||
|
|
- Measured RTT speed.
|
||
|
|
|
||
|
|
| debugger | char/s |
|
||
|
|
| ------------------------- | ------ |
|
||
|
|
| bmp stm32f723 stlinkv3 | 49811 |
|
||
|
|
| bmp stm32f411 black pill | 50073 |
|
||
|
|
| bmp stm32f103 blue pill | 50142 |
|
||
|
|
|
||
|
|
This is the speed at which characters can be sent from target to debugger probe, in reasonable circumstances. Test target is an stm32f103 blue pill running an [Arduino sketch](https://github.com/koendv/Arduino-RTTStream/blob/main/examples/SpeedTest/SpeedTest.ino). Default *monitor rtt poll* settings on debugger. Default RTT buffer size in target and debugger. Overhead for printf() calls included.
|
||
|
|
|
||
|
|
## Compiling firmware
|
||
|
|
To compile with RTT support, add *ENABLE_RTT=1*.
|
||
|
|
|
||
|
|
Eg. for STM32F103 blue pill:
|
||
|
|
```
|
||
|
|
make clean
|
||
|
|
make PROBE_HOST=stlink ENABLE_RTT=1
|
||
|
|
```
|
||
|
|
or for the STM32F411 *[Black Pill](https://www.aliexpress.com/item/1005001456186625.html)*:
|
||
|
|
```
|
||
|
|
make clean
|
||
|
|
make PROBE_HOST=f4discovery BLACKPILL=1 ENABLE_RTT=1
|
||
|
|
```
|
||
|
|
Setting an ident string is optional. But if you wish, you can set the default RTT ident at compile time.
|
||
|
|
For STM32F103 *Blue Pill*:
|
||
|
|
```
|
||
|
|
make clean
|
||
|
|
make PROBE_HOST=stlink ENABLE_RTT=1 "RTT_IDENT=IDENT\ STR"
|
||
|
|
```
|
||
|
|
or for STM32F411 *Black Pill*:
|
||
|
|
```
|
||
|
|
make clean
|
||
|
|
make PROBE_HOST=f4discovery BLACKPILL=1 ENABLE_RTT=1 "RTT_IDENT=IDENT\ STR"
|
||
|
|
```
|
||
|
|
Note the backslash \\ before the space.
|
||
|
|
|
||
|
|
## Links
|
||
|
|
- [OpenOCD](https://openocd.org/doc/html/General-Commands.html#Real-Time-Transfer-_0028RTT_0029)
|
||
|
|
- [probe-rs](https://probe.rs/) and [rtt-target](https://github.com/mvirkkunen/rtt-target) for the _rust_ programming language.
|
||
|
|
- [RTT Stream](https://github.com/koendv/Arduino-RTTStream) for Arduino on arm processors
|
||
|
|
- [\[WIP\] RTT support - PR from katyo](https://github.com/blacksphere/blackmagic/pull/833)
|