07b4e5726e
CMSIS-DAP: Run time detect DAP_SWD_SEQUENCE
...
Some dongles in the making like orbtrace may not yet support.
2021-10-31 12:55:41 +01:00
88e44d1c12
cmsis: use exception in wait_word().
2021-10-31 12:55:41 +01:00
a1d4649795
SWD: Use dp_low_write to allow multidrop scan.
2021-10-31 12:55:41 +01:00
4f36c1ddf8
Remove dp_low_read() and use exception protected dp_read()
2021-10-31 12:55:41 +01:00
f9d343af3e
cmsis: AP reads are posted. Read from RDBUFF.
2021-10-31 12:55:41 +01:00
d4ae308f9f
cmsis: implement srst_set_val()
2021-10-31 12:55:41 +01:00
166eb3ee3e
cmsis_dap: Always transfer 65 bytes with hid_read|write()
...
CMSIS-DAP Dragonprobe works on some devices. E.g. it does not work
on NUCLEO-F103
2021-10-31 12:55:41 +01:00
b343ebe06f
cmsis-dap/linux: Link against libhidapi-hidraw
...
libhidapi-libusb detaches a kernel module but does not reattach again.
This may wrack interaction with other programs using hidapi.
2021-10-31 12:55:41 +01:00
761e0230d4
cmsis-dap: Print messages when transfers fail.
...
Expect signal integrity errors when using jumper cables. Often probes switch
the SWJ GPIO with highest speed, resulting in possible reflections. Additional
ground wires may help. If there is isolation between probe and targets,
additional ground wires are a must or ground shift will wrack the transfer!
2021-10-31 12:55:41 +01:00
39fbffd3d2
stlinkv2: Fix low access to AP registers.
2021-10-31 12:55:41 +01:00
c13778139f
adiv5/hosted: Export the BMP_TYPE in DP.
2021-10-31 12:55:41 +01:00
485105221e
dap: Always work on a copy of the buffer when calling dbg_dap_cmd() in a loop
...
A better solution would use seperate buffers for dbg_dap_cmd. But as WAIT is
already handled in DAP, cahnces are low that loop re-entry is needed.
2021-10-31 12:55:41 +01:00
397fbd5749
cmsis: Only cmsis internal use must differentiate between HID and Bulk access
...
Missing DAP_SWD_SEQUENCE may eventually need a distinction visible from
outside later.
2021-10-31 12:55:41 +01:00
7b1eb6e6e3
bmp_libusb: reset type on every device.
2021-10-31 12:53:47 +01:00
80064c18a9
bmp_libusb: Fix CMSIS-DAP related memory leak.
2021-10-31 11:13:34 +01:00
c4b6b42dcf
stlinkv2: Read targetid on DPv2 devices.
2021-10-31 11:13:34 +01:00
e7e1bfdb53
mpsse: Fix using 60 MHz clock on fast devices.
2021-10-30 13:55:57 +02:00
99a5fdb6f8
bmp_remote: Better error propagation.
...
Negative values from platform_buffer_read are errors too!
2021-10-30 13:55:57 +02:00
f4117aa1b4
cdcacm: Use the USB strings.
2021-10-30 13:55:57 +02:00
f28f05952f
stlink: Add another STLINK-V3 ID.
2021-10-30 13:55:57 +02:00
e1a928beb1
Fixes to compile with gcc11 #925
...
Target code changes are pure for formal correctness and not tested!
2021-10-10 15:59:57 +02:00
e2d3161442
Removed -S message as debugger selection option since it is used for reading bytes
2021-10-09 21:38:48 +02:00
59282b6f66
Fixed typography
2021-10-09 21:18:52 +02:00
7274f55ff4
Fixed return value of hosted blackmagic in erase mode
2021-10-09 21:17:58 +02:00
3f54fba986
HOSTED_BMP_ONLY=0 by default on Linux.
...
The user is warned about missing dependencies.
2021-10-09 21:14:52 +02:00
7ccbdd98c0
hosted/dap: Copy command buffer in wait/retry loop.
...
The same buffer is used for both command and response, causing part of
the command to be overwritten before it’s retried. Solve this by saving
and restoring a copy of the command before retrying.
2021-10-05 23:21:07 +02:00
f69f29a660
f4discovery/blackpill: fix usbusart
2021-10-01 00:10:03 +02:00
554e34517e
Better reporting when monitor command fails.
2021-09-22 21:41:43 +02:00
64f756d627
Test voltage on VREF before enabling target power (mon tpwr), to avoid potential power conflict.
2021-09-22 20:45:18 +02:00
356325f563
ftdi_bmp: Fix bit select.
2021-09-22 15:16:20 +02:00
79066c950f
bmp_libusb: Remove duplicated libusb_init.
...
Thanks to Red Liu for noticing
2021-09-22 15:16:20 +02:00
da15cc3cb7
remote_jtagtap: Fix memory corruption in jtagtap_tdi_tdo_seq
2021-09-22 15:16:20 +02:00
a93e57e112
ftdi: Fixed wrong direction report in DEBUG.
2021-09-22 15:16:20 +02:00
01583560cd
hosted: Update Readme.md to use HOSTED_BMP_ONLY
2021-09-16 11:02:31 +02:00
ff79108f66
cl_utils: Increase worksize for increased speed.
...
H743 reads 2 MB in ~23 vs 27 seconds
2021-09-07 10:57:17 +02:00
a76a559656
pc/platform_delay: Wait ms and not us!
2021-09-07 10:57:17 +02:00
a297c8c8ad
hosted/Makefile.inc: Use gcc to build hosted, if not advised otherwise
2021-09-04 21:15:07 +02:00
698cfeb1f4
bmp_serial: Nag MACOS programmer to implement find_debuggers!
2021-09-04 21:15:07 +02:00
49122b50b6
hosted: Make HOSTED_BMP_ONLY the default.
...
Hopefully more people will use it when reporting errors!
2021-08-15 16:43:29 +02:00
2fcd4a878a
ftdi_bmp.h: Fix error when compiling with HOSTED_BMP_ONLY=1
2021-08-15 16:43:29 +02:00
6308506276
jtag: Make jtag_devs argument to jtag_handler.
2021-08-15 16:43:29 +02:00
f7670fcd44
ftdi_bmp: Add verbosity for libftdi_jtagtap_tdi_tdo_seq()
2021-08-15 16:43:29 +02:00
3df692ecb2
adiv5_swdp_scan: If SWD scan fails, try a JTAG scan.
2021-08-15 16:43:29 +02:00
5c8e277663
hosted/dap: Fix tdi_tdo_seq.
2021-08-15 16:43:29 +02:00
2d4a503135
jtag_scan: Rework chain detection
...
Fixme: stlinkv2/hosted probably does only handle STM devices. Check if
jtag_devs.c really needed.
2021-08-15 16:43:29 +02:00
e1a1865de9
remote/jtagtap_tdi_tdo_seq: Split up large transactions.
...
FIXME: One remote transaction still can only do up to 64 ticks, leaving
room for speed enhancement with larger transactions.
Firmware assumes (1LL << 65) == 0LL !
2021-08-15 16:43:29 +02:00
8084a75634
cl_utils: Allow Hardware reset from the command line
2021-08-15 16:43:29 +02:00
36836d0746
ftdi_bmp: Fix setting bits and FTDIJTAG srst.
2021-08-15 16:43:29 +02:00
cfdf55855e
ftdi_bmp: Export and use reset functions.
2021-08-15 16:43:29 +02:00
5eb43a1ddb
platforms: stm32f4x1 blackpillv2 as variant of f4discovery
...
Compile as make PROBE_HOST=f4discovery BLACKPILL=1
2021-08-13 16:18:05 +02:00
Uwe Bonnes
fabalthazar
Vegard Storheil Eriksen
Jeff Lutgen
Thiadmer Riemersma
Andy Makovec
aam335