77 lines
3.7 KiB
Plaintext
77 lines
3.7 KiB
Plaintext
#compdef blackmagic
|
|
# SPDX-License-Identifier: BSD-3-Clause
|
|
|
|
# Copyright (c) 2022 Rachel Mant
|
|
# All rights reserved.
|
|
#
|
|
# Redistribution and use in source and binary forms, with or without
|
|
# modification, are permitted provided that the following conditions are met:
|
|
#
|
|
# 1. Redistributions of source code must retain the above copyright notice, this
|
|
# list of conditions and the following disclaimer.
|
|
#
|
|
# 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
# this list of conditions and the following disclaimer in the documentation
|
|
# and/or other materials provided with the distribution.
|
|
#
|
|
# 3. Neither the name of the copyright holder nor the names of its
|
|
# contributors may be used to endorse or promote products derived from
|
|
# this software without specific prior written permission.
|
|
#
|
|
# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
# AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
# IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
# DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
|
# FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
# DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
# SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
# CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
# OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
|
|
_blackmagic_frequency() {
|
|
_numbers -u 'Hz' 'frequency' 'k:kilohertz' 'M:megahertz'
|
|
}
|
|
|
|
_blackmagic_size() {
|
|
_numbers -u 'B' 'size in bytes' 'k:kibibytes' 'M:mebibytes'
|
|
}
|
|
|
|
local arguments
|
|
|
|
arguments=(
|
|
'-h[show version and help then exit]'
|
|
'-l[list available supported probes]'
|
|
'-v=[set the output verbosity level]:number'
|
|
'(-d -P -s -c)-d=[use a serial device at the given path]:path:_files'
|
|
'(-d -P -s -c)-P=[use the <number>th debug probe found while scanning the system, see the output from list for the order]:number'
|
|
'(-d -P -s -c)-s=[select the debug probe with the given serial number]:serial'
|
|
'(-d -P -s -c)-c=[select the FTDI-based debug probe with of the given type]:type'
|
|
'-n=[select the target device at the given position in the scan chain]:number'
|
|
'-j[use JTAG instead of SWD]'
|
|
'-C[connect to target under hardware reset]'
|
|
'(-t -T)-t[perform a chain scan and display information about the conected devices]'
|
|
'(-t -T)-T[perform continues read- or write-back of a value to allow measurement of protocol timing. Aborted by ^C]'
|
|
'-e[assume external resistors for FTDI devices]'
|
|
'(-E -w -V -r)-E[erase the target device Flash]'
|
|
'(-E -w -V -r)-w[write the specified binary file to the target device Flash (the default)]'
|
|
'(-E -w -V -r)-V[verify the target device Flash against the specified binary file]'
|
|
'(-E -w -V -r)-r[read the target device Flash]'
|
|
'-p[power the target from the probe (if possible)]'
|
|
'-R-[reset the device. If followed by "h", this will be done using the hardware reset line instead of over the debug link]:: :(h)'
|
|
'-H[do not use the high level command API (bmp-remote)]'
|
|
'*-M[run target-specific monitor commands]:command'
|
|
'-a=[start address for the given Flash operation (defaults to the start of Flash)]:address:_numbers "address"'
|
|
'-S=[number of bytes to work on in the Flash operation (default is till the operation fails or is complete)]:_blackmagic_size'
|
|
':binary file to use in Flash operations:_files "*.bin"'
|
|
)
|
|
|
|
if ! (( $words[(Ie)-j] )); then
|
|
arguments+=(
|
|
'-f=[set an operating frequency for SWD]:frequency:_blackmagic_frequency'
|
|
'-m=[use the given target ID for selection in SWD multi-drop]:target'
|
|
)
|
|
fi
|
|
|
|
_arguments -s : $arguments
|