libsigrok/README.devices

363 lines
13 KiB
Plaintext
Raw Normal View History

2013-03-13 09:33:17 +00:00
-------------------------------------------------------------------------------
README.devices
-------------------------------------------------------------------------------
This README contains various notes for users of libsigrok (or frontends
that are based on libsigrok) about device- and/or driver-specific issues.
Firmware
--------
Some devices supported by libsigrok need a firmware to be uploaded every time
the device is connected to the PC (usually via USB), before it can be used.
The default location where libsigrok expects the firmware files is:
$prefix/share/sigrok-firmware
($prefix is usually /usr/local or /usr, depending on your ./configure options)
For further information see the section below and also:
http://sigrok.org/wiki/Firmware
Per-driver firmware requirements
--------------------------------
The following drivers/devices require a firmware upload upon connection:
- asix-sigma: The ASIX SIGMA and SIGMA2 require various firmware files,
depending on the settings used. These files are available from our
'sigrok-firmware' repository/project under a license which allows us
to redistribute them.
- fx2lafw: Logic analyzers based on the Cypress FX2(LP) chip need the
firmware files from the 'sigrok-firmware-fx2lafw' repository/project.
The firmware is written from scratch and licensed under the GPLv2+.
- hantek-dso: The Hantek DSO-2090 (and other supported models of the same
series of Hantek PC oscilloscopes) need firmware files.
These can be extracted from the vendor's Windows drivers using a tool
from our 'sigrok-util' repository/project.
- saleae-logic16: The Saleae Logic16 needs a firmware file for the
Cypress FX2 chip in the device, as well as two FPGA bitstream files.
These can be extracted from the vendor's Linux application using a tool
from our 'sigrok-util' repository/project.
2013-03-13 09:33:17 +00:00
The following drivers/devices do not need any firmware upload:
- agilent-dmm
- alsa
- brymen-dmm
2013-06-22 15:05:57 +00:00
- cem-dt-885x
- center-3xx
2013-03-13 09:33:17 +00:00
- chronovu-la8
- colead-slm
- demo
- fluke-dmm
2013-06-22 15:05:57 +00:00
- ikalogic-scanalogic2
- ikalogic-scanaplus
- kecheng-kc-330b
2013-03-13 09:33:17 +00:00
- lascar-el-usb
- link-mso19
2013-03-13 09:33:17 +00:00
- mic-985xx
2013-11-03 16:30:42 +00:00
- norma-dmm
2013-03-13 09:33:17 +00:00
- openbench-logic-sniffer
- rigol-ds
2013-03-13 09:33:17 +00:00
- serial-dmm
2013-11-03 16:30:42 +00:00
- teleinfo
2013-03-13 09:33:17 +00:00
- tondaj-sl-814
- uni-t-dmm
- uni-t-ut32x
2013-03-13 09:33:17 +00:00
- victor-dmm
- zeroplus-logic-cube
Specifying serial ports
-----------------------
Many devices supported by libsigrok use serial port based cables (real RS232
or USB-to-serial ones) to connect to a PC.
For all these devices, you need to specify the serial port they are connected
to (e.g. using the 'conn' option in sigrok-cli). It is not possible to scan
for such devices without specifying a serial port.
Example:
$ sigrok-cli --driver <somedriver>:conn=/dev/ttyUSB0 ...
The following drivers/devices require a serial port specification:
- agilent-dmm
- brymen-dmm
2013-06-22 15:05:57 +00:00
- cem-dt-885x
- center-3xx
2013-03-13 09:33:17 +00:00
- colead-slm
- fluke-dmm
- link-mso19
2013-03-13 09:33:17 +00:00
- mic-985xx
2013-11-03 16:30:42 +00:00
- norma-dmm
2013-03-13 09:33:17 +00:00
- openbench-logic-sniffer
- serial-dmm
2013-11-03 16:30:42 +00:00
- teleinfo
2013-03-13 09:33:17 +00:00
- tondaj-sl-814
The following drivers/devices do not require a serial port specification:
- alsa
- asix-sigma
- chronovu-la8
- demo
- fx2lafw
- hantek-dso
2013-06-22 15:05:57 +00:00
- ikalogic-scanalogic2
- ikalogic-scanaplus
- kecheng-kc-330b
2013-03-13 09:33:17 +00:00
- lascar-el-usb
- rigol-ds
- saleae-logic16
2013-03-13 09:33:17 +00:00
- uni-t-dmm
- uni-t-ut32x
2013-03-13 09:33:17 +00:00
- victor-dmm
- zeroplus-logic-cube
Permissions of serial port based devices
----------------------------------------
When using devices supported by libsigrok that use serial port based cables
(real RS232 or USB-to-serial ones) to connect to a PC, you need to ensure
that the user running the libsigrok frontend has (read/write) permissions to
access the serial port device (e.g. /dev/ttyS0, /dev/ttyUSB0, and so on).
You can use 'chmod' to apply permissions as you see fit, and/or 'chown' to
change the owner of the serial port device to a certain user or group.
For USB-to-serial based devices, we recommended using our udev rules file
(see below for details).
Permissions for USB devices (udev rules file)
---------------------------------------------
When using USB-based devices supported by libsigrok, the user running the
libsigrok frontend (e.g. sigrok-cli) has to have (read/write) permissions
for the respective USB device.
On Linux, this is accomplished using either 'chmod' (not recommended) or
using the udev rules file shipped with libsigrok (recommended).
The file is available in contrib/z60_libsigrok.rules. It contains entries
for all libsigrok-supported (USB-based) devices and changes their group
to 'plugdev' and the permissions to '664'.
When using a libsigrok package from your favorite Linux distribution, the
packager will have already taken care of properly installing the udev file
in the correct (distro-specific) place, and you don't have to do anything.
The packager might also have adapted 'plugdev' and '664' as needed.
If you're building from source, you need to copy the file to the place
where your distro expects such files. This is beyond the scope of this README,
but generally the location could be e.g. /etc/udev/rules.d, or maybe
/lib/udev/rules.d, or something else. Afterwards you might have to restart
udev, e.g. via '/etc/init.d/udev restart' or similar, and you'll have to
re-attach your device via USB.
Please consult the udev docs of your distro for details.
Cypress FX2 based devices
-------------------------
Devices using the Cypress FX2(LP) chip without any specific USB VID/PID will
be enumerated with VID/PID 04b4:8613 (the default for "unconfigured FX2").
These are usually "FX2 eval boards" (that can also be used as LAs, though).
On Linux, the 'usbtest' driver will usually grab such devices, and they will
thus not be usable by libsigrok (and frontends).
You can fix this by running 'rmmod usbtest' as root before using the device.
UNI-T DMM (and rebranded models) cables
---------------------------------------
UNI-T multimeters (and rebranded devices, e.g. some Voltcraft models) can
ship with different PC connectivity cables:
- UT-D04 (USB/HID cable with Hoitek HE2325U chip, USB VID/PID 04fa:2490)
- UT-D04 (USB/HID cable with WCH CH9325 chip, USB VID/PID 1a86:e008)
- UT-D02 (RS232 cable)
The above cables are all physically compatible (same IR connector shape)
with all/most currently known UNI-T multimeters. For example, you can
use either of the UT-D04 USB/HID cables or the UT-D02 RS232 cable with
the UNI-T UT61D multimeter.
When using the UT-D02 RS232 cable with any of the supported UNI-T DMMs,
you have to use the respective driver with a '-ser' drivername suffix
(internally all of these models are handled by the 'serial-dmm' driver).
You also need to specify the serial port via the 'conn' option, e.g.
/dev/ttyUSB0 (attached via a USB-to-serial cable) or /dev/ttyS0 (actual
RS232 port) on Linux (see above).
Finally, the user running the frontend (e.g. sigrok-cli) also needs
permissions to access the respective serial port (see above).
Examples (sigrok-cli):
$ sigrok-cli --driver uni-t-ut61e-ser:conn=/dev/ttyUSB0 ...
$ sigrok-cli --driver voltcraft-vc820-ser:conn=/dev/ttyS0 ...
When using any of the UT-D04 USB/HID cables you have to use the respective
driver _without_ the '-ser' drivername suffix (internally all of these models
are handled by the 'uni-t-dmm' driver).
You also need to specify the USB vendor/device IDs of the cable.
Autodetection is not possible here, since various other products use the
USB VID/PID of those cables too, and there is no way to distinguish them.
2013-03-13 09:33:17 +00:00
Since the UT-D04 cables are USB based (but don't use a USB-to-serial chip)
there is no need to specify a serial port via 'conn', of course.
However, the user running the frontend does also need to have permissions
to access the respective USB device (see above).
Examples (sigrok-cli):
$ sigrok-cli --driver uni-t-ut61e:conn=1a86.e008 ...
$ sigrok-cli --driver voltcraft-vc820:conn=04fa.2490 ...
2013-03-13 09:33:17 +00:00
UNI-T UT-D04 cable issue on Linux
---------------------------------
The UNI-T UT-D04 cable with Hoitek HE2325U (or WCH CH9325) chip seems to have
2013-04-25 15:42:20 +00:00
a very specific problem on Linux. Apparently it requires to be put into
2013-03-13 09:33:17 +00:00
suspend (and woken up again) before it is usable. This seems to be a
Linux-only issue, Windows is not affected by this since apparently the
Windows kernel does this for every USB device, always.
Thus, if you want to use any of the UNI-T DMMs with this specific cable,
you'll have to run the following script (as root) once, every time you attach
the cable via USB. The script was written by Ralf Burger.
See also: http://erste.de/UT61/index.html
#!/bin/bash
for dat in /sys/bus/usb/devices/*; do
if test -e $dat/manufacturer; then
grep "WCH.CN" $dat/manufacturer > /dev/null && echo auto > ${dat}/power/level && echo 0 > ${dat}/power/autosuspend
fi
done
Enabling multimeter / data logger measurement output
----------------------------------------------------
Some multimeters or data loggers will not start outputting measurement data
unless a certain action has been performed by the user beforehand. This is
usually mentioned in the vendor manual of the respective device, but here's
a short list for convenience:
- Digitek DT4000ZC: Briefly press the "RS232" button.
- PCE PCE-DM32: Briefly press the "RS232" button.
- RadioShack 22-812: Press and hold "SELECT" and "RANGE" together.
- TekPower TP4000ZC: Briefly press the "RS232" button.
- UNI-T UT61D: Press the "REL/RS232/USB" button for roughly 1 second.
- UNI-T UT325: Briefly press the "SEND" button (as per manual). However, it
appears that in practice you don't have to press the button (at least on
some versions of the device), simply connect the device via USB.
- V&A VA18B: Keep the "Hz/DUTY" key pressed while powering on the device.
- Victor 70C: Press the "REL/RS232" button for roughly 1 second.
- Victor 86C: Press the "REL/RS232" button for roughly 1 second.
2013-06-22 15:05:57 +00:00
- Voltcraft VC-830: Press the "REL/PC" button for roughly 2 seconds.
2013-03-13 09:33:17 +00:00
ALSA driver
-----------
The 'alsa' driver can be used to sample analog data using a PC's soundcard.
I.e. the sound card can act as a simple oscilloscope (with some limitations)
using commercial or DIY "sound card scope probe" cables.
Since ALSA is a Linux-specific sound system, this driver will inherently
only compile and work on Linux.
We might write additional drivers to make a similar functionality available
on other OSes at some point.
Link Instruments MSO-19
-----------------------
The driver for the Link Instruments MSO-19 mixed-signal oscilloscope (MSO)
is currently using libudev (which is a library for the Linux-specific udev
system). Thus, this driver can currently only compile and work on Linux.
We plan to fix this though, so that it'll work on all other OSes, too.
2013-03-13 09:33:17 +00:00
ChronoVu LA8 USB VID/PIDs
-------------------------
The ChronoVu LA8 logic analyzer is available in two revisions. Previously,
the LA8 shipped with a USB VID/PID of 0403:6001, which is the standard ID
for FTDI FT232 USB chips.
Since this made it hard to distinguish the LA8 from any other device
with this FTDI chip connected to the PC, the vendor later shipped the
LA8 with a USB VID/PID of 0403:8867.
The 'chronovu-la8' driver in libsigrok supports both VID/PID pairs and
automatically finds devices with either VID/PID pair. However, currently
the driver will assume any device with VID/PID 0403:6001 is a ChronoVu LA8.
OLS
---
The Dangerous Prototypes Openbench Logic Sniffer (OLS) logic analyzer is
supported by the 'ols' driver in libsigrok. This driver assumes a somewhat
recent firmware has been flashed onto the OLS (it doesn't need a firmware
upload every time it's attached via USB, since the firmware is stored in the
device permanently).
The most recent firmware version that is tested is 3.07.
If you use any older firmware and your OLS is not found or is not working
properly, please upgrade to at least this firmware version. Check the
Dangerous Prototypes wiki for firmware upgrade instructions:
http://dangerousprototypes.com/docs/Logic_Sniffer_upgrade_procedure
Also, you need to specify a serial port for the OLS in the frontends, e.g.
using the 'conn' option in sigrok-cli, and you also need to have the
permissions to access the serial port (see above).
Example:
$ sigrok-cli --driver ols:conn=/dev/ttyACM0 ...
Rigol DS oscilloscopes
----------------------
2013-03-13 09:33:17 +00:00
The 'rigol-ds' driver (for the Rigol DS series DSOs) currently uses the Linux
usbtmc kernel driver. This means it can currently only be built and used on
Linux (i.e., it's non-portable).
2013-03-13 09:33:17 +00:00
The use of a kernel module also means it is dependent on the kernel version
used, as well as on whether this specific module is available in the kernel.
Additionally, the usbtmc kernel module has been known to have various bugs
in some versions. These are some (but not all) drawbacks of using a kernel
module as opposed to a libusb-based driver that works in user-space.
We plan to change the driver to use the 'librevisa' user-space shared
library (which uses libusb) soon, which will fix all these issues and make
the driver portable at the same time.