Trying to configure an invalid capture ratio would reset the
previously configured value. Instead, we should just reject the
new value and keep the original one.
With this driver it is possible to set voltage target and current
limit. Also enabling and disabling the output is possible.
Analog output sends read back values from output. If output is
disabled analog outputs 0.00.
In protocol.c there is a g_usleep() call. This gives almost
every time enough time for PSU to parse and process input.
Multichannel devices aren't supported.
Instead of using a non-standard packed attribute, read the contents of the
probe EEPROM into a buffer and then process it using the R* macros.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Standard integer types may differ in size on different targets. Use fixed-size
types instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This fixes parts of bug #423.
The list of fixed warnings:
src/output/srzip.c:285:3: warning: Value stored to 'ret' is never read
ret = zip_append(o, logic->data, logic->unitsize, logic->length);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/scpi/scpi.c:610:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/scpi/scpi.c:667:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/dmm/vc870.c:410:2: warning: Value stored to 'info_local' is never read
info_local = (struct vc870_info *)info;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/conrad-digi-35-cpu/api.c:130:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/fx2lafw/api.c:658:2: warning: Value stored to 'timeout' is never read
timeout = fx2lafw_get_timeout(devc);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/protocol.c:941:3: warning: Value stored to 'retc' is never read
retc = SR_ERR_ARG;
^ ~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/api.c:168:2: warning: Value stored to 'model' is never read
model = METRAHIT_NONE;
^ ~~~~~~~~~~~~~
src/hardware/ikalogic-scanalogic2/api.c:325:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/openbench-logic-sniffer/api.c:185:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/rigol-ds/api.c:813:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/scpi-pps/api.c:405:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/yokogawa-dlm/api.c:239:2: warning: Value stored to 'ret' is never read
ret = SR_ERR_NA;
^ ~~~~~~~~~
Timer intervals shorter than about 100 ms are unnecessarily taxing
on system resources. Also, on systems like Windows the smallest
resolvable time unit without using high precision timers is about
15 ms. Regular timer intervals should be well above that value to
avoid being dominated by noise and round-off.
Firmware versions starting with 00.02.04 apparently cause the in and out
bulk endpoints to end up in a HALT state. This is likely related to the
larger transfer size quirk implemented in the Linux kernel for the Rigol
DS1000: this USBTMC implementation does not have that workaround.
Instead, if the firmware version is >= 00.02.04, both endpoints have the HALT
condition cleared on device close.
This fixes bug #354.
GPIO direction should be set once right after exporting. There's no need
to reset it again - in fact it's a bug which causes the probe to be reset
every time the value is read/set and gives incorrect results when reading
the GPIO values with direction == 'in'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision B of ACME hardware introduces probes with on-board at24cs02
EEPROM. Extend the ACME driver to support reading the contents of
the EEPROM via linux' sysfs interface.
Also: make the driver be able to tell the difference between revisions,
add new GPIO layout and set the shunt resistance for revB at probe
registration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Only perform a single check at initialization time to see if the probe is
equipped with a power-switch. This is done in preparation for revision B
support which has this kind of information encoded in EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
After opening the USB device, set the device configuration to 1.
Actually, do it twice, just as the vendor driver seems to do. This
is supposed to trigger a lightweight reset of the device.
Originally, I omitted this reset sequence from the sigrok driver
because it simply did not work at all for me. However, it does seem
to work now, so that may have been a problem in libusb or the kernel
which is now fixed.
With some luck, this change may finally fix#327.
Use states SR_ST_ACTIVE and SR_ST_INACTIVE to indicate that the
device is open or closed, respectively. Do not use any of the
other state values. Improve the robustness of the open and close
methods in face of errors. Introduce a separate flag to indicate
that a running acquisition should be canceled.
Prepare the trigger masks at config_commit() time, so that the
trigger setup can be validated before starting an acquisition.
Accordingly, do actually report validation errors back to the
caller.
It turns out that g_stat() breaks apart when using 64 bit stat on
32-bit systems. Since the actual type of GStatBuf is decided when
glib/gstdio.h is included, it is thus possible for GLib itself to
be compiled with a different type than user code.
Ouch. Unfortunately going back to plain stat() also means that we
lose Unicode filename support on Windows.
Since Autoconf places some important feature flags only into the
configuration header, it is necessary to include it globally to
guarantee a consistent build.
A few of these were pretty serious, like missing arguments,
passing integers where a string was expected, and so on.
In some places, change the types used by the code rather than
just the format strings.
Martin Ling
Tilman Sauerbeck
Uwe Hermann
Daniel Elstner
Karl Palsson
Hannu Vuolasaho
Bartosz Golaszewski
Martin Lederhilger
Bert Vermeulen
Aurelien Jacobs