Allow channel groups to be swapped. This is useful
for demux at 200mhz with the unbuffered channels.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
The Tecpel DMM-8060 was added since we assumed it would be a rebadged
Voltcraft VC-820 (since we know the Tecpel DMM-8061 is a rebadged VC-840).
However, according to the vendor webpage it doesn't have PC connectivity
at all, so drop it for now (until someone can confirm that it does or does
not actually have RS232/USB connectivity).
These two drivers are currently unfinished and don't work, so disable
and "unhook" them for now in preparation of the next libsigrok release.
They're still in the git repository, but not hooked up to the build
system, so that they won't get detected or built, and also don't end up
in the release tarball.
Since link-mso19 is the only driver that currently requires libudev,
drop any reference to that, too.
It should be relatively easy to apply this patch in reverse after the
release to bring back both drivers.
These two drivers are currently unfinished and don't work, so disable
and "unhook" them for now in preparation of the next libsigrok release.
They're still in the git repository, but not hooked up to the build
system, so that they won't get detected or built, and also don't end up
in the release tarball.
Since link-mso19 is the only driver that currently requires libudev,
drop any reference to that, too.
It should be relatively easy to apply this patch in reverse after the
release to bring back both drivers.
sr_config_get() provides a GVariant owned by the caller, so it must be
released with g_variant_unref() when done.
sr_config_set() takes a GVariant from the caller which may be floating;
it will be properly sunk and release after use by this function. Thus
the output of g_variant_new_*() may be used as an argument.
sr_config_list() also provides a GVariant owned by the caller, to be
unreferenced when done.
sr_config_make() can take a floating reference.
- Explicitly list .config_get in all drivers for consistency, and set it
to NULL if unused (whether or not a driver implements it is optional).
- List all 'struct sr_dev_driver' entries in the same order in all drivers.
- Move the check whether .config_set/.config_list exist (i.e., are non-NULL)
into sanity_check_all_drivers().
Check the relevant arguments for != NULL before calling the actual
driver-specific function, so that the driver can safely assume those
arguments are non-NULL. This removes the need to duplicate these
checks in every driver.
Also, do some minor whitespace and consistency improvements.
Check the relevant arguments for != NULL before calling the actual
driver-specific function, so that the driver can safely assume those
arguments are non-NULL. This removes the need to duplicate these
checks in every driver.
Also, change one SR_ERR to the more correct SR_ERR_MALLOC, and assign
sr_ctx in the rigol-ds1xx2's hw_init() function, like all the other
drivers do.
This takes an sr_config key and returns a list of possible values for
that key to be submitted with config_set(). The format of the list and
its contents is dependent on the key.
This will replace the SR_DI_* keys that returned such a list before,
such as SR_DI_SAMPLERATES.
The alsa driver was out of date wrt APIs and libsigrok conventions in
general, and wasn't compiling.
This fixes the compile and updates it to _basically_ work with the current
state of analog support in libsigrok.
This is not finished/full support for ALSA analog sampling yet, though,
various TODOs remain that will be addressed later.
This works with the UNI-T UT-D02 (RS232) cable. For the USB/HID
based cable (UNI-T UT-D04), the uni-t-dmm driver must be used.
Note: This is untested, but should work just fine for all settings, with
the possible exception of temperature (testers needed!)
Use the infrastructure of serial-dmm to handle the RadioShack 22-812,
and completely remove radioshack-dmm.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Prepare the tekpower-dmm driver to be able to support various simple
serial port based DMMs.
Also, make a 'tekpower-tp4000zc' "first-class" driver which is currently
the only user of this generic driver.
The 'uni-t-dmm' driver/directory will not appear as a "driver" to
frontends anymore, it's just an internal thing.
The frontends will see a uni-t-ut61d and voltcraft-vc820 driver now,
with the correct names and parsers etc. attached to them.
This is not fully finished yet, but it's a start (and works mostly):
$ sigrok-cli -D
The following devices were found:
UNI-T UT61D with 1 probe: P1
Voltcraft VC-820 with 1 probe: P1
$ sigrok-cli --driver voltcraft-vc820 -D
The following devices were found:
Voltcraft VC-820 with 1 probe: P1
$ sigrok-cli --driver uni-t-ut61d -D
The following devices were found:
UNI-T UT61D with 1 probe: P1
# Now attaching a UNI-T UT61D device via USB.
$ sigrok-cli --driver uni-t-ut61d --samples 3 -O analog
P1: -0.017800 V DC
P1: -0.017600 V DC
P1: -0.017700 V DC
# Now attaching a Voltcraft VC-820 device via USB instead.
$ sigrok-cli --driver voltcraft-vc820 --samples 3 -O analog
P1: -0.319200 V DC
P1: -0.319300 V DC
P1: -0.319300 V DC
Aurelien Jacobs
Bert Vermeulen
Matt Ranostay
Marcus Comstedt
Uwe Hermann
Florian Knodt
Florian Steinhardt
Marc Schink
Alexandru Gagniuc
Joel Holdsworth
Martin Ling
Peter Stuge