With this driver it is possible to set voltage target and current
limit. Also enabling and disabling the output is possible.
Analog output sends read back values from output. If output is
disabled analog outputs 0.00.
In protocol.c there is a g_usleep() call. This gives almost
every time enough time for PSU to parse and process input.
Multichannel devices aren't supported.
Instead of using a non-standard packed attribute, read the contents of the
probe EEPROM into a buffer and then process it using the R* macros.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Standard integer types may differ in size on different targets. Use fixed-size
types instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This fixes parts of bug #423.
The list of fixed warnings:
src/output/srzip.c:285:3: warning: Value stored to 'ret' is never read
ret = zip_append(o, logic->data, logic->unitsize, logic->length);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/scpi/scpi.c:610:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/scpi/scpi.c:667:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/dmm/vc870.c:410:2: warning: Value stored to 'info_local' is never read
info_local = (struct vc870_info *)info;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/conrad-digi-35-cpu/api.c:130:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/fx2lafw/api.c:658:2: warning: Value stored to 'timeout' is never read
timeout = fx2lafw_get_timeout(devc);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/protocol.c:941:3: warning: Value stored to 'retc' is never read
retc = SR_ERR_ARG;
^ ~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/api.c:168:2: warning: Value stored to 'model' is never read
model = METRAHIT_NONE;
^ ~~~~~~~~~~~~~
src/hardware/ikalogic-scanalogic2/api.c:325:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/openbench-logic-sniffer/api.c:185:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/rigol-ds/api.c:813:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/scpi-pps/api.c:405:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/yokogawa-dlm/api.c:239:2: warning: Value stored to 'ret' is never read
ret = SR_ERR_NA;
^ ~~~~~~~~~
Timer intervals shorter than about 100 ms are unnecessarily taxing
on system resources. Also, on systems like Windows the smallest
resolvable time unit without using high precision timers is about
15 ms. Regular timer intervals should be well above that value to
avoid being dominated by noise and round-off.
Firmware versions starting with 00.02.04 apparently cause the in and out
bulk endpoints to end up in a HALT state. This is likely related to the
larger transfer size quirk implemented in the Linux kernel for the Rigol
DS1000: this USBTMC implementation does not have that workaround.
Instead, if the firmware version is >= 00.02.04, both endpoints have the HALT
condition cleared on device close.
This fixes bug #354.
GPIO direction should be set once right after exporting. There's no need
to reset it again - in fact it's a bug which causes the probe to be reset
every time the value is read/set and gives incorrect results when reading
the GPIO values with direction == 'in'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision B of ACME hardware introduces probes with on-board at24cs02
EEPROM. Extend the ACME driver to support reading the contents of
the EEPROM via linux' sysfs interface.
Also: make the driver be able to tell the difference between revisions,
add new GPIO layout and set the shunt resistance for revB at probe
registration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Only perform a single check at initialization time to see if the probe is
equipped with a power-switch. This is done in preparation for revision B
support which has this kind of information encoded in EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
After opening the USB device, set the device configuration to 1.
Actually, do it twice, just as the vendor driver seems to do. This
is supposed to trigger a lightweight reset of the device.
Originally, I omitted this reset sequence from the sigrok driver
because it simply did not work at all for me. However, it does seem
to work now, so that may have been a problem in libusb or the kernel
which is now fixed.
With some luck, this change may finally fix#327.
Use states SR_ST_ACTIVE and SR_ST_INACTIVE to indicate that the
device is open or closed, respectively. Do not use any of the
other state values. Improve the robustness of the open and close
methods in face of errors. Introduce a separate flag to indicate
that a running acquisition should be canceled.
Prepare the trigger masks at config_commit() time, so that the
trigger setup can be validated before starting an acquisition.
Accordingly, do actually report validation errors back to the
caller.
It turns out that g_stat() breaks apart when using 64 bit stat on
32-bit systems. Since the actual type of GStatBuf is decided when
glib/gstdio.h is included, it is thus possible for GLib itself to
be compiled with a different type than user code.
Ouch. Unfortunately going back to plain stat() also means that we
lose Unicode filename support on Windows.
Since Autoconf places some important feature flags only into the
configuration header, it is necessary to include it globally to
guarantee a consistent build.
A few of these were pretty serious, like missing arguments,
passing integers where a string was expected, and so on.
In some places, change the types used by the code rather than
just the format strings.
The Hung-Chang DSO-2100 is a parallel port PC oscilloscope sold back
in 1999 under brand names like Protek and Voltcraft.
This inital version of the driver has the following limitations:
- Hardcoded calibration values. All parameters are set to 50%.
- No support for auto triggering
- No support for TV sync trigger modes
- No support for the "scroll acquisition" mode
In scroll acquisition mode the device behaves more like a multimeter
and reports the current voltage of a probe on request. While in this
mode the sample rate is limited by the parallel port interface, it is
the only way to capture both channels at the same time (well, sort of).
Calibration would need auto triggering. The calibration values are very
temperature dependent and the device takes literally hours to reach its
final temperature. Every vdiv setting needs its own set of calibration
values. Without hardware modifications, the calibration settings wear
of in less than a second while waiting for a trigger because the
capacitors storing those values are not recharged in state 0x21.
In sr_session_iteration(), remove the inverted evaluation of the
block parameter if a USB source is present. This stops the deluge
of USB event callbacks due to the timeout always being zero.
Also, just for cleanliness, initialize the revents member of each
GPollFD instance to zero.
Move the include flags for files in the source tree from
configure.ac to Makefile.am where they belong. Also use
AM_CPPFLAGS instead of CFLAGS/CXXFLAGS to make sure the
files in the build/source tree are always picked up first.
Also, remove the include/libsigrok sub-directory from the
search path, thereby making the <libsigrok/> prefix mandatory
when building libsigrok itself. This matches the convention
already imposed on users of the library.
- Don't #include <errno.h> in files that don't actually need it.
- Don't use strerror() on error codes from functions that don't set
errno. Replace strerror() with sr_strerror() for libsigrok functions.
Fixes a bug where new acquisition failes due to leftover pipes from
previous acquisitions:
sr: demo: dev_acquisition_start: pipe() failed
Indeed, PulseView had 2024 pipes opened. With this fix, it stabilizes at
33 with sampling thread active.
Signed-off-by: Hubert CHAUMETTE <hchaumette@baylibre.com>
Move the libusb_detach_kernel_driver() call after the code that
sets the usb->devhdl pointer, otherwise it'll be NULL and result
in a segfault.
#0 libusb_kernel_driver_active (dev=0x0, interface_number=0) at libusb/core.c:1711
#1 dev_open (sdi=0x12d99f0) at src/hardware/fx2lafw/api.c:374
[...]
Tested on a device with the default Cypress VID/PID and one with
the Saleae Logic VID/PID, both works fine.
The timerfd descriptor is closed automatically by
g_io_channel_shutdown(). No need to close it manually.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
At high sampling rates and maximum channels we are not able to acquire
samples fast enough, even though frontends still think that samples
arrive on time. This causes visible shifts in frontend plots.
To compensate for the delay introduce the following workaround: check
if we are late (if any clock events have been missed) and resend the
last frame n times (n == number of missed clock events).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently baylibre-acme uses a fake pipe as the input channel required by
libsigrok API and calls sleep() in the data acquisition callback to create
intervals between measurements.
Switch to a more elegant approach: use Linux' timerfd and set a periodic
timer equal to the sampling rate. Then read the data every time the timer
expires.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Opening a file has a cost (security, allocation, syscalls). The
read_sample() function always does an open/read/close sequence.
In order to optimize that, let's open the file at the moment the
acquisition starts, close it when the acquisition stops and make
read_sample() only lseek() to the beginning of the file and read
the value.
Signed-off-by: Daniel Lezcano <daniel.lezcano@free.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This was originally done as an optimization in combination with a list
reversal which has since been removed from the code. Thus, un-reverse
the channels so that the UI lists them in the correct order again.
The Chroma 62000P series comes in various models with different
current and voltage capabilities. These are encoded in the *IDN
string, so just get them from there, rather than needing a profile
for every model.
All those options are currently applied only to power-supplies
but they could apply as well to electronic loads, except for the
fact that electronic loads channels are called inputs and not
outputs.
Also when you think about an SMU (or any kind of 4-quadrants
power-supply), their channels can both source and sink current,
so they can be considered as input as much as output.
Those SR_CONF_* are thus renamed so that they can be used in all
those situations.
For devices such as the HP 6632B the following invocation was failing due to
scpi_cmd(sdi, SCPI_CMD_SELECT_CHANNEL, ...) returning SR_OK_CONTINUE.
./sigrok-cli -d scpi-pps:conn=/dev/ttyUSB0:serialcomm=9600/8n1 --continuous
sr: session: sr_session_start: could not start an acquisition (not enough data to decide error status yet)
Failed to start session.
Daniel Elstner
Karl Palsson
Hannu Vuolasaho
Bartosz Golaszewski
Martin Lederhilger
Uwe Hermann
Bert Vermeulen
Aurelien Jacobs
Daniel Glöckner
Hubert CHAUMETTE
Soeren Apel
Daniel King
Daniel Lezcano
Daniel Gröber
Carl-Fredrik Sundström
Alexandru Gagniuc
Marcus Comstedt