Use serial_readline in acquisition mode, otherwise data from the
Re:load Pro could get lost.
Use reloadpro_receive_data() for all commands when in acquisition
mode. When not using a single point of receiving data, data could get
lost.
Prefer sigrok's endianess conversion helper over the inet htons()
routine which is harder to read (is "network order" little or big?).
Writing the conversion results in units of bytes also avoids misaligned
memory access. The header length is odd, each payload item got written
as an uint16_t item to an odd address.
The config.h file must always be included as first file.
src/output/csv.c: In function 'gen_header':
src/output/csv.c:64:20: warning: format '%u' expects argument of type 'unsigned int', but argument 3 has type 'uint64_t {aka long long unsigned int}' [-Wformat=]
#define LOG_PREFIX "output/csv"
^
./src/libsigrok-internal.h:753:42: note: in expansion of macro 'LOG_PREFIX'
#define sr_info(...) sr_log(SR_LOG_INFO, LOG_PREFIX ": " __VA_ARGS__)
^
src/output/csv.c:244:3: note: in expansion of macro 'sr_info'
sr_info("Set sample period to %" PRIu64 " %s",
^
src/output/csv.c: In function 'dump_saved_values':
src/output/csv.c:462:34: warning: format '%u' expects argument of type 'unsigned int', but argument 3 has type 'uint64_t {aka long long unsigned int}' [-Wformat=]
g_string_append_printf(*out, "%" PRIu64 "%s",
^
In file included from src/hardware/ftdi-la/protocol.c:21:0:
src/hardware/ftdi-la/protocol.c: In function 'send_samples':
src/hardware/ftdi-la/protocol.h:28:20: warning: format '%u' expects argument of type 'unsigned int', but argument 3 has type 'uint64_t {aka long long unsigned int}' [-Wformat=]
#define LOG_PREFIX "ftdi-la"
^
./src/libsigrok-internal.h:751:42: note: in expansion of macro 'LOG_PREFIX'
#define sr_spew(...) sr_log(SR_LOG_SPEW, LOG_PREFIX ": " __VA_ARGS__)
^
src/hardware/ftdi-la/protocol.c:29:2: note: in expansion of macro 'sr_spew'
sr_spew("Sending %" PRIu64 " samples.", samples_to_send);
^
Optionally create multiple analog channels in serial-dmm's scan()
routine. Allow the meters' parse routines to fill in more than one
analog value from the inspection of a single packet.
Use "large" (4 times 14 bytes) packets for the Metex M-3860M and the
PeakTech 4390A meters, and have those large packets parsed by wrapping
the routines for regular 14-byte Metex packets, and sending four values
to the session bus after reception of one large packet.
Thanks to Frank Stettner <frank-stettner@gmx.net> for testing and
fixing the initial implementation of this extension.
Move the initial assignment to the 'offset' variable to the very spot
where it gets evaluated and subsequently manipulated.
Replace a DIY copy loop with the corresponding memmove(3) call.
Also use "r" and "f" as trigger slope values for now, since that's
what most other drivers do currently.
This also fixes two scan-build issues:
api.c:559:3: warning: Value stored to 'tmp_str' is never read
tmp_str = g_variant_get_string(data, NULL);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
api.c:561:9: warning: Use of memory after it is freed
ret = siglent_sds_config_set(sdi, "%s:TRSL %s",
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The strcasestr() function is non-portable (e.g. not available on
MinGW, possibly elsewhere). Replace it with g_strstr_len() for the time
being. While the latter is not case-insensitive it appears that
that property doesn't matter here ("." should not be relevant anyway,
and e.g. an SDS1202X-E does indeed report "Mpts" as such).
Should it become necessary to have this code be case-insensitive,
we'll have to find a more portable solution than strcasestr().
This causes some compile errors on platforms where RPC is not available, e.g.
siglent-sds/api.c:25:21: fatal error: rpc/rpc.h: No such file or directory
Surrounding the #include (and later code) with "#if HAVE_RPC" should avoid
these compile errors, but since it's not used at all for now, drop it.
Implement a first version of the driver for the Siglent SDS1000 and
SDS2000 oscilloscopes.
[ gsi: This commit corresponds to git 0228126017e6 of marchelh's tree,
I adjusted the source to closer match the project's coding style. The
conversion was verified by this command:
$ git diff --word-diff=color -w -b <branch>:<dir> <branch>:<dir>
Changes include: Whitespace adjustment, dead code removal, separation
of variable declaration and assignment, alpha-sorted includes. Line
length was not addressed and not every location got adjusted, to keep
the diff minimal and to reduce effort during review of this version. ]
Check for successful allocation before accessing struct members. Return
with an error from device initialization when allocation fails.
This was reported by clang's scan-build.
Make sure to release the allocated "pod enabled" memory, too, when SCPI
communication during channel setup fails. Defer the return with an error
(instead of duplicating the free() invocation).
This was reported by clang's scan-build.
Few DMM drivers already did it. This commit adjusts the remaining DMM
drivers, to set the "DC" flag for measurements in diode mode.
This fixes bug #144.
Although I don't have the hardware to test, the nature of the change and
the arrangement of driver code suggests it's good. When a meter already
communicated the "DC" status, the change does nothing and won't harm.
The change ensures "DC" is flagged for those meters which previously
didn't, which is desirable.
Explicitly assign NULL to param to avoid the "may be used uninitialized"
warning reported in bug #1094. Behaviour remains unchanged. All references
to the variable were under "if (!conn)", and the assigning arm of the
branch checked for "if (!param)" after assignment. So the error could
not happen, but compilers may not have noticed depending on the width of
their scope during compilation.
Move the initialization of 'conn' closer to the conditional assignment,
such that all paths are seen in one spot during maintenance.
This fixes bug #1094.
api.c: In function 'config_set':
api.c:352:5: warning: format '%ld' expects argument of type 'long int', but argument 3 has type 'uint64_t' [-Wformat=]
sr_err("invalid sample range 2k...64M: %ld",
^
beaglelogic_tcp.c: In function 'beaglelogic_tcp_send_cmd':
beaglelogic_tcp.c:114:3: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'size_t' [-Wformat=]
sr_dbg("Only sent %d/%lu bytes of command: '%s'.", out,
^
Check pointers' validity before dereferencing them. Release partially
allocated memory in an error path. Remove an assignment which never took
effect.
This was reported by clang's scan-build.
Each code path either assigns to 'flags', or leaves the routine. There
is no potential path that leaves the variable at the initially assigned
value, so the assignment took no effect. Remove it.
Nit: Trim the source code line length while we are here.
This was reported by clang's scan-build.
Check pointers' validity before dereferencing them. Explicitly assign a
default value to variables, before conversion routines conditionally
assign the "real" value (and don't in case of conversion errors). This
avoids processing "garbage" data.
Strictly speaking I cannot see how the conversion routine returns OK and
has _not_ assigned a result. But the explicit assignment won't harm
either, and matches the fallback when the conversion fails (detectibly).
Which means that runtime behaviour won't change.
This was reported by clang's scan-build.
Remove an assignment that won't take effect. Check pointers' validity
before dereferencing. Fix a memory leak.
This was reported by clang's scan-build.
Check for successful allocation of multiple memory ranges, and release
partial allocations in the error path when one of them failed. This
fixes a potential memory leak, as well as avoids NULL dereferences.
This was reported by clang's scan-build.
Silence warnings about assigned values that never get used, potential
NULL deference, and potential memory leaks.
This was reported by clang's scan-build.
The scan_2x_bd232() routine used to always prepare one spare context,
and filled it in when a device was found, just to allocate another one
and continue scanning.
Free the last allocated context unconditionally, as it was allocated
unconditionally, and never used.
This was reported by clang's scan-build.
Stick with the prepared but unfinished "limit msec" code path, but
silence the warning about an unused variable value.
This was reported by clang's scan-build.
After the first capture ->num_frames never got to be _equal_
to ->limit_frames; fixed by resetting to zero in dev_acquisition_stop(),
and protected against similar problems in the future by switching to
greater-or-equal instead.
[Note: This patch is basically a squashed version of the initial driver
commits by Andreas Zschunke <andreas.zschunke@gmx.net>, two fixes by
Andrej Valek <andy@skyrain.eu>, and various coding style / cosmetic
fixes by Uwe Hermann <uwe@hermann-uwe.de> to make the driver a lot more
consistent with the rest of the libsigrok code-base.]
When refactoring the code, some places where sr_scpi_send was replaced
by rigol_ds_config_set the first argument was not changed from sdi->conn
to sdi. Fix the remaining ones.
Fix: https://sigrok.org/bug/1073
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
This regression was introduced in f1ba6b4b2c.
Due to how the sysclk-lwla driver does up to 3 open/close operations in
one dev_open() API callback we cannot rely on the sr_dev_open() and
sr_dev_close() wrappers setting the sdi->status variable in this case.
Tested on LWLA1034.
Some drivers used locale dependent functions for converting strings
to float/double values. These functions fail when the decimal mark
is a "," in the locale settings but the string contains a ".".
This fixes bug #1064.
A "low samplerate" in this case means anything where
samples_todo is less than SAMPLES_PER_FRAME. This case
wasn't handled properly before, resulting in wrong
amounts of data being sent out.
We can't use the memory size command because it returns
the *maximum* memory used, not the *actual* memory used.
Hence, we only know the number of samples per div once
sample data actually comes in.
As there is a huge range of supported LeCroy scopes, naming
the IDN response for every single one of them is going to be
impossible. Hence, it makes more sense to treat all LeCroy
devices as if they were scopes and supported. This approach
lets users try to see how far they get and if they run into
issues, they can then be treated separately - e.g. by creating
a custom device profile.
Unless we do this, the vast majority of LeCroy scopes will
not be recognized by the driver.
Uwe Hermann
Sven Bursch-Osewold
James Churchill
Axel Hinrichs
Frank Stettner
Gerhard Sittig
marchelh
Romain Tartière
Soeren Apel
Philipp Marek
Andreas Zschunke
Michał Janiszewski
Stefan Brüns
Holger Müller
Timo Rothenpieler
Sylvain Pelissier
Joel Holdsworth