This change makes it so that we don't run the event loop inside
the commit. It's not clear this is an issue, but it seems safer
not to.
Fixes: lp:1852589
* https://bugs.launchpad.net/kicad/+bug/1852589
We were running into various corner conditions where a tool's event
loop would exit while the tool was still active, or the tool would
get popped while we were still in the event loop. (A lot of these
had to do with the POINT_EDITOR's, but not all of them.)
The new architecture:
1) tools always do a Push()/Pop()
2) everyone is responsible for their own pops; no more stack-clearing
on a cancel
3) CancelInteractive events go to all tools to facilitate (2)
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
If the user is carefully selecting the zone edge, we do not filter the
zone preemptively from our disambiguation list in the same manner as we
do for selecting on zone copper.
Fixes: lp:1796719
* https://bugs.launchpad.net/kicad/+bug/1796719
Allows selection of polygons and zones by their visible area. Will only
select polygons/filled areas when they are unobstructed by other
elements in the footprint/pcb. Also adds a "skip heuristics" modifier
key for clicking (ALT) that allows the full disambiguation list to be
displayed without removing less-likely elements. This dovetails the
zone/polygon selection as it allows selecting even when areas a fully
overlapped.
Fixes: lp:1753153
* https://bugs.launchpad.net/kicad/+bug/1753153
New algorithm more targetted and just clears the items. This
also obviates the need for the aQuietMode flags.
Only fixes one part of the bug, but the "fixes" line is the
easiest way to get a link in the bug to the commit.
Fixes: lp:1786727
* https://bugs.launchpad.net/kicad/+bug/1786727
Some other tools (in this case the POINT_EDITOR) aren't good
citizens and activate themselves when receiving selection
changes.
Fixes: lp:1785781
* https://bugs.launchpad.net/kicad/+bug/1785781
This not only reduces the number of different mechanisms, but
will also reduce (yet again) the number of Clarify Selection
pop-ups (because the CLIENT_SELECTION_FILTER runs before the
pop-up, while SanitizePads ran after it).
Fixes: lp:1710451
* https://bugs.launchpad.net/kicad/+bug/1710451
(cherry picked from commit e50a993)
The old item pointers (which aren't safe to keep around) were
removed in favour of opaque references (void*) which are then
compared against existing items when needed.
Also improves brightening by brightening the whole footprint
(ie: its pads, drawings, reference and value) rather than just
its target cross.
(cherry picked from commit 30e90b0)
Commit complementary to 4f0c9b6b. In case there were multiple tracks
under the cursor, disambiguation was shown twice because
SELECTION_TOOL::selectConnection() cleared the selection and requested
it again.
Some actions, such as select trivial connection, don't need the
user to choose which trace at a corner to start from -- either
one will do. Same for moving a simple trace corner.
Likewise, Edit in Footprint Editor shouldn't ask if you mean the
footprint or the pad. Obviously it's the footprint.
This change adds a CLIENT_SELECTION_FILTER which allows clients
to do tool- or action-specific filtering of the selection before
the disambiguation menu is run.
It also removes some tool- and action-specific code which was
in the selection_tool and shouldn't have been.
Fixes: lp:1708869
* https://bugs.launchpad.net/kicad/+bug/1708869
- added TOOL_INTERACTIVE::resetTransitions()
- made protected and moved TOOL_BASE::setTransitions() to TOOL_INTERACTIVE
- TOOL_MANAGER calls TOOL_INTERACTIVE::resetTransitions() instead of
setTransitions()
This patch adds a radiobox to allow the user to select a reference point for
the move. The additional options are: User Origin (set with <space>),
Grid Origin and Sheet Origin (effectively making it an absolute coordinate).
A checkbox is added (where it makes sense) to allow overriding which point
within the component is put on top of the designated coordinate.
Fixes: lp:1460460
* https://bugs.launchpad.net/kicad/+bug/1460460
This simplifies the (already simple) SELECTION_AREA class. It is also
moved into KIGFX::PREVIEW and put in the common library, where it can be
reused by other GAL-aware tools (not just in Pcbnew) in future.
- The tools can now specify if the items in the selection must be editable/
deletable. This is groundwork to be able to select/delete DRC markers, which can't
otherwise be edited.
- Fixed disappearing of selected objects
Jeff Young
Seth Hillbrand
Tomasz Włostowski
Carsten Schoenert
Maciej Suminski
Kristoffer Ödmark
Oliver Walters
Robbert Lagerweij
John Beard
jean-pierre charras