Dynamic casts should only be used when we explicitly check for the
resulting pointer to be NULL. Where we know the class is castable we
can use static_cast, save on overhead and ensure our resulting pointer
is non-null.
m_dragstatus is set to true when a valid route is created given the
user's constraints. We need to check this before committing the route
to the board.
Fixes: lp:1794810
* https://bugs.launchpad.net/kicad/+bug/1794810
Snapping while dragging depends on the current net being assigned during
dragging. This initializes the placer to hold the current net while
performing inline dragging. The placer is reset along with the dragger
in StopRouting(). This fixes the difference in snap between drag and
create new route.
( cherry-picked from 219695953 )
Using Title + Message wasn't working for all the dialogs which
did substitutions in the message (which was a lot of them).
Fixes: lp:1789348
* https://bugs.launchpad.net/kicad/+bug/1789348
Use standard Magnetize() to handle grid and magnetic pads.
Use the standard menu from PCB_TOOL. Delegating the menu to
the SELECTION_TOOL just caused grief.
Also brings clients (such as Position Relative To) into line,
and implements better Cancel behaviour.
Also improves visibility of modal status messages:
- moves Select Anchor message from status bar to popup
- moves Select Reference message from dialog to popup
Fixes: lp:1786727
* https://bugs.launchpad.net/kicad/+bug/1786727
Also fixes some interactivity issues in the microwave tools around
single-click tools that have initial properties dialogs. Those
need to act kind of like a hybrid between single-click and two-click
tools.
Fixes: lp:1751381
* https://bugs.launchpad.net/kicad/+bug/1751381
... and GetMsgPanelInfo.
Step 4 in the g_UserUnit eradication effort.
Also removes a couple of conversion routines that were close
enough to extinction.
(cherry picked from commit c75da51)
In Cairo, we don't have z-ordering implemented, so we need to draw the
clearance outline first otherwise it will draw a large, grey overlay
that hides the actual track while routing.
Fixes: lp:1779228
* https://bugs.launchpad.net/kicad/+bug/1779228
Minimum differential pair clearance should be limited to the netclass
differential pair spacing. This also cleans up some unused code that
was left over from previous work on differential pair clearances.
Fixes: lp:1673632
* https://bugs.launchpad.net/kicad/+bug/1673632
After an action is completed that required the screen to pan when the
cursor reaches the edge of the screen, we should release the cursor to
allow the user to move their mouse without panning.
Fixes: lp:1763860
* https://bugs.launchpad.net/kicad/+bug/1763860
- Ordering of Hotkey list by function
- Use Hotkey assignment instead of hard-coded hotkey for length tuning
- Adjust default Length Tuning settings hotkey to CTRL-L so that we
don't overlap with "Lock" (overlaps are not editable)
PNS routing options allow trace width to be chosen by the assigned
netclass. This extends that to differential pair width/gap settings as
well.
Fixes: lp:1672126
* https://bugs.launchpad.net/kicad/+bug/1672126
1) hide the status popup when the dialog is brought up
2) forward events from the popup to the canvas so hotkeys work
3) make sure diff pair radius is always 100%
4) fix greyed-out Miter style label
5) make L a hotkey so it works before you start dragging
Fixes: lp:1545856
* https://bugs.launchpad.net/kicad/+bug/1545856
Previously, dragging changes were applied only if the last cursor move
finished with a successful drag operation. It made items squeezing
difficult, as it required accurate cursor movement to apply the changes.
When counting items, many cases exist where we want to count all items
without checking flags. This short-circuits the loop to provide the
immediate count.
Changes SHAPE_CONVEX to SHAPE_SIMPLE to better reflect the limitations.
Changes SHAPE_LINE_CHAIN::PointInside calculation to allow points
strictly inside a line chain
Fixes: lp:1768862
* https://bugs.launchpad.net/kicad/+bug/1768862
Usually pads do not overlap. However custom pads are represented as
their convex hull, so they may enclose other pads. This change allows the
router to select the closest pad to the cursor position.
Corrects an error in polyline estimation
Syncs graphics to world PNS by whole layer set rather than
individual layer at a time.
Prevents reloading of full pns TOOL_BASE during reset of tools unless
the tool is being activated.
Fixes: lp:1766626
* https://bugs.launchpad.net/kicad/+bug/1766626
Previous algorithm used a static variable which it decremented
for each new unconnected track, but this resulted in the router
marking earlier fixed segments as collisions (because they
would get set to netcode = 0 when "fixed").
Fixes: lp:1762043
* https://bugs.launchpad.net/kicad/+bug/1762043
If the track being routed is unconnected, or the end-point
clicked on is unconnected, allow the connection by changing
the unconnected item to the net of the connected one.
Fixes: lp:1548129
* https://bugs.launchpad.net/kicad/+bug/1548129
Track dragging forces the cursor position, which is still kept when PNS
router is launched again. It is avoided by resetting the force cursor
position option before running the event loop.
Launching right click context menu overrides the cursor position, so all
actions executed by the tools will be performed in the right click
position. It created an issue, as the overridden cursor settings were
saved into wrong context if there was another tool activated in the
meantime.
Current implementation saves cursor settings for all tools and restores
them once the right click context menu disappears.
Fixes: lp:1745981
* https://bugs.launchpad.net/kicad/+bug/1745981
Fixes: lp:1746507
* https://bugs.launchpad.net/kicad/+bug/1746507
Some actions, such as select trivial connection, don't need the
user to choose which trace at a corner to start from -- either
one will do. Same for moving a simple trace corner.
Likewise, Edit in Footprint Editor shouldn't ask if you mean the
footprint or the pad. Obviously it's the footprint.
This change adds a CLIENT_SELECTION_FILTER which allows clients
to do tool- or action-specific filtering of the selection before
the disambiguation menu is run.
It also removes some tool- and action-specific code which was
in the selection_tool and shouldn't have been.
Fixes: lp:1708869
* https://bugs.launchpad.net/kicad/+bug/1708869
Tomasz Włostowski
Seth Hillbrand
Jeff Young
Franck78
jean-pierre charras
Maciej Suminski
John Beard
Jon Evans
Camille