Add missing check for root sheet when searching sheet hierarchies for
already loaded schematics. This prevents the root sheet from being
omitted when adding new sheets using the root sheet file name.
CHANGED: Make file name tests case sensitive so that schematic sheet
file names on non-Windows systems can be uses as expected.
Warn users when attempting to use schematic file names that only vary
by case sensitivity that doing so will result in a project that is not
portable to Windows.
Fixes lp:1843415
https://bugs.launchpad.net/kicad/+bug/1843415
When dragging a bus the entry is connected to the bus so the wire
connected to the entry (if any) needs to stretch.
While an entry can connect in the middle of bus, it cannot connect
in the middle of a wire.
Fixes: lp:1849973
* https://bugs.launchpad.net/kicad/+bug/1849973
The aperture option created a Connector pad only on the paste layer.
This is incorrect: the SMD type only is acceptable.
5connector is *only* for edge card connectors.
Moreover, The dialog did not even accept the setting defined by this dialog...
- Previously a warning was generated even for not connectable pads
(pads not on copper layers or without pad name).
- The test is now optional and is disabled by default.
(pads without corresponding pin is schematics are a frequent case)
Fixes: lp:1852444
https://bugs.launchpad.net/kicad/+bug/1852444
We must add the new node for the new file in the new directory,
not in the original root directory. The file watcher will also
delete the old node, so there is no point in renaming the file.
Fixes: lp:1852357
* https://bugs.launchpad.net/kicad/+bug/1852357
Revert "Be a bit smarter about moving files through a rename."
Revert "Check for file moving directory and refresh entire tree if so."
This reverts commit f8aea249df.
This reverts commit 8ce04d3362.
This change makes it so that we don't run the event loop inside
the commit. It's not clear this is an issue, but it seems safer
not to.
Fixes: lp:1852589
* https://bugs.launchpad.net/kicad/+bug/1852589
Not able to draw a keepout-area on bottom or internal layers.
This was due to a behavior specific to the footprint editor,
not disabled in board editor.
Fixes: lp:1852847
https://bugs.launchpad.net/kicad/+bug/1852847
Remove not used files:
- markdown2html is not used (we are using "Sundown" tool)
- newstroke_font_without_CJK.cpp is removed.
Due to code optimization the full font works fine without memory issues
-fix also a few very minor compil warnings
In high contrast mode, the holes of buried vias and microvias were no darkened when not on the active layer.
In high contrast mode, the outer circle of buried vias and microvias were alway darkened.
In high contrast mode, when the selected layer is non visible through-vias are now darkend.
Fixes: lp:1844982
* https://bugs.launchpad.net/kicad/+bug/1844982
CHANGED: No longer call schematics noname.sch in standalone mode,
instead don't given them any name so the user can choose on save.
Fixes: lp:1852607
* https://bugs.launchpad.net/kicad/+bug/1852607
Ensure we iterate over all the sub directories and files inside of them
when deleting a directory from the project tree.
Fixes: lp:1852357
* https://bugs.launchpad.net/kicad/+bug/1852357
We have different requirements than sheet paths for netlists,
so going through that code and then doing a lot of conversions
just ends up with a mess.
We now generate the path directly from the SCH_SHEET_PATH.
Fixes: lp:1852353
* https://bugs.launchpad.net/kicad/+bug/1852353
The sort routine requires the value to be true with a is strictly lower
than b. But just inverting the '<' doesn't yield strictly lower, it
includes '>='. This causes items to jump in the list.
Copy/Paste should keep the original items' designation for all units and
conversion type. If it was specified in the original copy, we should
keep the same specification when pasting (but update for the current
frame)
Handle symbols as well as strings in the "source" lists of
netlist files.
Handle Protex gerber file extensions.
Check for project_name-whatever pattern for files that we
don't recognize (such as project_name-NPTH-drl_map.ps)
Previously, the build version would only update if the dialog_about.cpp
file were modified. This moves the date generation into the same file
as the build version, so it will be updated whenever a new version
is made.
NEW: The simulator plot now avoids colors already in use, if possible.
The palette is replaced with a larger one with less saturated colors.
Fixes: lp:1851372
* https://bugs.launchpad.net/kicad/+bug/1851372
NEW: A text entry allows adding signals by name. This includes vectors
not in the signal list, which is useful for plotting calculated vectors
like `let AB=V(a)*V(b)`. It's also a faster way to add a signal if you
know its name already.
Fixes: lp:1851373
* https://bugs.launchpad.net/kicad/+bug/1851373
Remove the NEW tag and only support the ADD tag for new features. ADD
is compatible with the other tags because the past tense (ED) makes
sense for ADD not NEW.
Ian McInerney
Fabien Corona
Wayne Stambaugh
Jeff Young
jean-pierre charras
Seth Hillbrand
evanshultz
qu1ck
Jonatan Liljedahl