This places the arc approximation setting in the kicad_pcb file and uses
it for all parts of the board rendering where arcs are converted to
segments. This allows the user to customize their speed vs. accuracy
tradeoff. The default setting of maximum error of 0.005mm is acceptable
for small boards on moderate systems.
This removes the remaining hard-coded segments counts and replaces them
with the relative error calculation where the segments per arc is
determined by the maximum error we allow (smaller arcs = fewer segments)
Give the user the option of cancelling a file open if there are
segment zones; otherwise they're converted to polygon fills.
Fixes: lp:1823087
* https://bugs.launchpad.net/kicad/+bug/1823087
the filled areas can use a hatch pattern (crossing lines) using square holes.
The zone filler removes too small holes (truncated holes) from hatch pattern.
It avoid to create small holes when a hole pattern is truncated by the filled area base shape.
Previously, in many cases the selected zone was refilled on exit selection, even if the zone was not modified.
This is annoying, because the zone fill can be really time consuming, and cannot be called without a good reason.
Now the refilling is made only if a zone parameter is actually modified.
Depending on thermal reliefs size, the polygons could be self intersecting,
and these self intersecting polygons are unexpected in zone calculations.
Other fix: the width of thermal stubs is clamped to the size of pads.
Previously, a bug in clamping calculations prevents constraining thermal stubs width.
Fixes: lp:1818752
https://bugs.launchpad.net/kicad/+bug/1818752
Where we can get away with lower segment counts (localizing an anchor),
we keep the low-def 16 segment count. Intermediate values and values
that are visible to the user are set to high definition. Most are
simply hints to the inflation correction but where they show, the user
show see smooth lines.
Separate out zone edges (which are quite specific, and should
win over most other things) from zone fills (which are pretty
generic and should only be considered when there's nothing else).
Also excludes zone fills when the zones aren't being shown as
filled.
We no longer require this as we calculate the number of segments based
on the maximum deviation rather than fixed numbers.
Fixes: lp:1780518
* https://bugs.launchpad.net/kicad/+bug/1780518
Allows selection of polygons and zones by their visible area. Will only
select polygons/filled areas when they are unobstructed by other
elements in the footprint/pcb. Also adds a "skip heuristics" modifier
key for clicking (ALT) that allows the full disambiguation list to be
displayed without removing less-likely elements. This dovetails the
zone/polygon selection as it allows selecting even when areas a fully
overlapped.
Fixes: lp:1753153
* https://bugs.launchpad.net/kicad/+bug/1753153
... and GetMsgPanelInfo.
Step 4 in the g_UserUnit eradication effort.
Also removes a couple of conversion routines that were close
enough to extinction.
(cherry picked from commit c75da51)
Be consistent with order, formatting, etc.
Remove debug stuff such as zone timestamp and net code.
Clean up misleading pad messages.
(cherry picked from commit 2132109)
It also fixes a corner case, when 2 zone with zone clearance = 0 are overlapping with different priorities
(previously, they were shortened)
Fixes: lp:1713028
https://bugs.launchpad.net/kicad/+bug/1713028
- support for background color setting
- removed several global config settings (such as g_Drc_On)
- wrapped most of global config settings in PCB_GENERAL_SETTINGS class
- reorganized PCB general options dialog to clearly mark which options concern only the legacy canvas
- new GAL feature for legacy users: double-click (or E) to change track width available as an option.
Fixes: lp:1530543
* https://bugs.launchpad.net/kicad/+bug/1530543
Fixes: lp:1707145
* https://bugs.launchpad.net/kicad/+bug/1707145
Fixes: lp:1698697
https://bugs.launchpad.net/kicad/+bug/1698697
The incorrect method ZONE_CONTAINER::AppendCorner() is also fixed:
It was expecting the corner must be added to the main outline, but this is a false expectation:
it can be added to a hole inside the zone outline.
Jeff Young
jean-pierre charras
Seth Hillbrand
Maciej Suminski
Tomasz Włostowski
Marvin Schmidt
Oliver Walters
Oliver Walters