When using "Place Text" the crosshair was freezing if cancelled before
placing text.
After the crosshair freezes, the next uses of the "Place Text" or
"Add Dimension" caused the crosshair to jump to the screen location
where the previously the crosshair was frozen.
Cancelling the "Add Dimension" caused the crosshair to jump to the
screen location where the crosshair was when cancelled on the next use
of the "Place Text" or "Add Dimension".
Fixes: lp:1822578
* https://bugs.launchpad.net/kicad/+bug/1822578
This behavior existed in 5.0.x but did not properly exit the edit tool
in 5.1. This removes stops the edit tool when we begin dragging a track
using the interactive router.
Fixes: lp:1820312
* https://bugs.launchpad.net/kicad/+bug/1820312
(cherry picked from commit c8118e3ce4)
When removing a point from the polygon, the vertex is removed before it
is tested for validity. If it fails validation, the edit is reverted
and the point count doesn't change, so the view update only modifies the
existing points. But the revert may also have changed the shared
pointer to the point array, invalidating the view's copy.
Fixes: lp:1821909
* https://bugs.launchpad.net/kicad/+bug/1821909
(cherry picked from commit 940aef77af)
Previously, refilling a zone after edition was made silently,
thus creating not understandable but very noticeable freeze time for complex zones.
(cherry picked from commit 3692c511d0)
Highlight connections is meant to show the copper connections on a
board. We remove the non-copper pads from our selection when attempting
to source the net for highlighting.
Fixes: lp:1815898
* https://bugs.launchpad.net/kicad/+bug/1815898
Choosing the drag origin should not be dependent on the snap settings in
pcbnew. Snap settings are sensible when you are designating a target
only. Additionally, when dragging a module, we do not want the
footprint's pads to be used as targets for snapping.
Fixes: lp:1814402
* https://bugs.launchpad.net/kicad/+bug/1814402
Snapping to item options were partially disconnected when unifying
framework. This re-attaches the options and adds the additional option
for graphical items.
Fixes: lp:1801377
* https://bugs.launchpad.net/kicad/+bug/1801377
Rather than selecting an arbitrary track to snap, we select the closest
track to our point, allowing the via to be placed along the full track
length.
Fixes: lp:1813324
* https://bugs.launchpad.net/kicad/+bug/1813324
Prior to placing the via, we check if the resulting via will pass too
close to different nets on different layers.
Fixes: lp:1718827
* https://bugs.launchpad.net/kicad/+bug/1718827
When creating the zone cutout, we delete the old zone and add a new one
with each cutout. This requires resetting the source zone and clearing
our previous selection if we would like to continue using the cutout
tool on the new zone.
Fixes: lp:1812339
* https://bugs.launchpad.net/kicad/+bug/1812339
There is some odd interaction in the default copy constructor for
TOOL_EVENT using boost::optional under gcc. Avoid this by explicitly
constructing the event needed for cut
Fixes: lp:1812848
* https://bugs.launchpad.net/kicad/+bug/1812848
- Added ignore netcode option to CONNECTIVITY_DATA::GetConnectedItems()
- PlaceModule() now ensures the module added to the board (and thus to the connectivity database) has correct bounding box necessary for R-trees to work
- Use recursive connected pad search so that the new net is propagated to all pads
Fixes: lp:1787961
* https://bugs.launchpad.net/kicad/+bug/1787961
When renumbering pads, you can click on a pad the second time to restore
the pad to its original value. This did not allow a user to then place
the removed number on the correct pad (assuming a mistake). This commit
ensures that removed pad numbers are remembered and allow the user to
place in the correct pad.
The local/dynamic ratsnest needs to calculate on a per-pad basis as the
module is always listed as having a visible ratsnest. This fixes the
finalized ratsnest viewed when routing as well as the show local
ratsnest regression.
Fixes: lp:1811010
* https://bugs.launchpad.net/kicad/+bug/1811010
Frame refresh in wxWidgets sets the focus back to indeterminate state
and prevents hotkey action until the focus is captured again. Using
canvas update is the correct method to update the canvas display after
modifying zones/similar
Fixes: lp:1810993
* https://bugs.launchpad.net/kicad/+bug/1810993
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Checks for ratsnest enabled prior to calculating and displaying the
local/dynamic ratsnest. Calls the ratsnest clear from selection clear
Notably, it appears that the tool actions do not chain transitions for
the same event. So only a single action (first specified) will be
executed when an event fires unless the actions are executed by separate
tools.
Fixes: lp:1809752
* https://bugs.launchpad.net/kicad/+bug/1809752
This fixes the handling of align/distribute tool when called on locked
items. Locked items cannot be moved but they may be used for the target
of an align/distribute operation.
Fixes: lp:1808238
* https://bugs.launchpad.net/kicad/+bug/1808238
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
Graphic lines and polygons are drawn to fit specific areas for which it
is helpful to have the endpoint controlled by the cursor even when
constraining the angle.
Fixes: lp:1805502
* https://bugs.launchpad.net/kicad/+bug/1805502
* Do not compile dxf old files.
* import gfx, gal mode: make absolute placement working.
* Import gfx in legacy canvas: use it and make interactive placement working
* Take imported line width in account. Ensure DXF line thickness is OK.
* handling empty files in legacy mode.
Martin McNamara
Jon Evans
Seth Hillbrand
jean-pierre charras
Tomasz Włostowski