We report bitmaps as being 'on' a copper layer because they are
associated with it but they are not actually physical parts so should
not be included in the DRC checks
Additionally, Bitmaps effective shape starts are the top left corner
rather than the center (unclear why that was there in the first place)
Fixes https://gitlab.com/kicad/code/kicad/issues/14065
We need a more advanced dirtying system for this to work out for
many users, it turns out. Right now too many changes cause full
zone refills which interrupt workflow.
Rounded line ends when deflating leads to microscopic jags in the
outline that are not visible but add substantial computation time and
minor error when computing polygon offsets.
Instead, the chamfer deflate method prevents these jagged lines by
clipping angles < 90° by the error level. This does not impact deflate
calls where we explicitly require the angles to be maintained
The link maps were actually disabled by default before
912f1d5cec, and required KICAD_MAKE_LINK_MAPS
to be provided to enable them. So switch back to disabling them by
default.
Also, The lld linker is unable to accept a single dash cref option, while
ld and gold can. Instead, use the double dash version that is supported
by all three.
xref: https://github.com/llvm/llvm-project/issues/60932
Co-authored-by: aris-kimi <aris_kimi@hotmail.com>
Co-authored-by: Ian McInerney <ian.s.mcinerney@ieee.org>
This adds Reset() method to KIFACE to reload global libs stored in
global static vars.
Also refactors some lib reload code in various frames to have
common MAIL_RELOAD_LIB handler.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/12500
When checking the physical clearance on a layer, it is critical to check
that the via hole exists on that layer. Blind/buried and micro vias may
not overlap, so should be excluded from this check when they don't exist
on a particular layer
Similarly, we should only be reporting a single physical clearance error
for each item pair even though they may have multiple errors across
multiple layers in the case of via-via clearance
Since the always plot the edge cuts layer option was deprecate,
the ability to plot multiple board layers was exposed through the
PLOT_CONTROLLER object.
Added the interactive plot information which was overlooked during
version 7 development.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/13841
Nominally, the zcode of a vertex is unique. This is not 100% true,
however, as we must interlace two 32-bit numbers into a single 32-bit
number. Sorting needs to account for the possibility that the zcode
will be the same while other elements of the vertex are different. This
commit fixes the broken boolean logic to more clearly handle these cases
Fixes https://gitlab.com/kicad/code/kicad/issues/13867
When adding new data, we may have differing sizes of the dynamic
ratsnest and our local copy, so ensure that we are only referencing
elements that exist in both
When two zones with the same net and same priority overlap, they should
both be filled, matching the behavior of v6. If you would like an
explicit override of one or the other, you need to set the zone priority
higher. Relying on the UUID as a tie breaker is good for zones with
different nets but creates unexpected changes from v6 when applying it
to zones of the same net
This makes it clearer that the overrides are not inverses of each
other -- one overrides the flashing state and the other overrides
the connection state (to other zones, not to everything).
Also fixes a bug where we were failing to check the force-no-connect
for pads.
If removing unused via annular ring option is enabled on a layer, then the via will have the ring if both:
- Via center is not inside a rule area with "Keep out copper fill" flag set
- Highest-priority zone the via hole intersects with has the same net
Pads will be flashed if:
- Pad center is not inside a rule area with "Keep out copper fill" flag set
- Highest-priority zone at the pad center has the same net
Fixes https://gitlab.com/kicad/code/kicad/issues/12964
1) Special case doesn't work for polygons with holes
2) Fix special case to handle intersecting lines where neither end is
in the polygon.
Note that only (1) is required for the bug below. (2) was just
discovered while implementing (1).
Fixes https://gitlab.com/kicad/code/kicad/issues/13779
Remove some useless spacers, and do not force some widgets to have a to
large size (by removing empty areas).
Work in progress: one panel is still too big.
Internal routines have no need for locking the mutex they already own.
While external routines that want to recalculate the Ratsnest do need an
exclusive lock before being allowed access
Fixes https://gitlab.com/kicad/code/kicad/issues/13011
Just testing a single point to find copper that is outside the board works
until the arc->segment conversion moves the board outline just enough to
have the filled copper slightly (few IU) outside of the converted outline.
Instead, we do an expensive check of comparing the size of the
intersection between the island and the island's intersection with the
board. If the intersection is at least half as large as the original
island, we can say with certainty that the island is inside. The margin
could be much smaller than half but this preserves the intent without
picking an arbitrary number that might be violated
Fixes https://gitlab.com/kicad/code/kicad/issues/13717
Jon Evans
Seth Hillbrand
Alex
qu1ck
Marek Roszko
aris-kimi
Ian McInerney
jean-pierre charras
Mike Williams
Jeff Young
Wayne Stambaugh