This leaves them untranslated internally but makes sure their
translation strings exist so they can be dynamically translated
at the GUI level.
Fixes https://gitlab.com/kicad/code/kicad/issues/6020
Switch Eeschema to use the built-in printing routines
because its precisions are close to those and it is
cleaner.
Give mils a precision of 2 decimal places to match
the precision shown in inches.
These objects can now be used in advanced DRC rules and
not just for keeping things out. Also remove the restriction
that at least one of the "basic" keepout rules must be set,
so that these areas can be used for more advanced rules.
ViewGetLOD() returns the minimal value of a zoom to show an item.
However a zoom is a double, and using int as minimal value does not
allows setting a correct value in some cases.
Also fixes a bunch of naming issues, primarily with lowercase for
protected variables, but also some for consistency with other parts
of the code.
Also changes the zone fill radio buttons in Board Setup to be more
generic referring to legacy vs. current, and to have tooltips.
Fixes https://gitlab.com/kicad/code/kicad/issues/5583
1) For a while now we've been using a calculated seg count from a given
maxError, and a correction factor to push the radius out so that all
the error is outside the arc/circle. However, the second calculation
(which pre-dates the first) is pretty much just the inverse of the first
(and yields nothing more than maxError back). This is particularly
sub-optimal given the cost of trig functions.
2) There are a lot of old optimizations to reduce segcounts in certain
situations, someting that our error-based calculation compensates for
anyway. (Smaller radii need fewer segments to meet the maxError
condition.) But perhaps more importantly we now surface maxError in the
UI and we don't really want to call it "Max deviation except when it's
not".
3) We were also clamping the segCount twice: once in the calculation
routine and once in most of it's callers. Furthermore, the caller
clamping was inconsistent (both in being done and in the clamping
value). We now clamp only in the calculation routine.
4) There's no reason to use the correction factors in the 3Dviewer;
it's just a visualization and whether the polygonization error is
inside or outside the shape isn't really material.
5) The arc-correction-disabling stuff (used for solder mask layer) was
somewhat fragile in that it depended on the caller to turn it back on
afterwards. It's now only exposed as a RAII object which automatically
cleans up when it goes out of scope.
6) There were also bugs in a couple of the polygonization routines where
we'd accumulate round-off error in adding up the segments and end up with
an overly long last segment (which of course would voilate the error
max). This was the cause of the linked bug and also some issues with vias
that we had fudged in the past with extra clearance.
Fixes https://gitlab.com/kicad/code/kicad/issues/5567
If we don't uniformly use the copy CTOR, we miss the additional
properties held by the superclass.
This also adds additional crash protection in GetMsgPanelInfo for zones
although it should never be triggered
Fixes https://gitlab.com/kicad/code/kicad/issues/5530
When running a hit test to check if the anchors are connected, we should
loosen the check for tracks to account for the width. Otherwise
connected anchors can be connected in the system but test positive for
IsDangling()
Fixes https://gitlab.com/kicad/code/kicad/issues/5027
There were a lot of plotters, exporters, etc. that were rolling their
own implementations.
This also introduces a lazily-built set of SHAPE objects for doing
collision detection and some forms of rendering (and later DRC).
Jeff Young
Ian McInerney
Marek Roszko
Mikolaj Wielgus
Jon Evans
jean-pierre charras
Tomasz Wlostowski
Seth Hillbrand
Maciej Suminski