It shows much more detail. Removes some nag dialogs and places
hypertext links in others.
Also fixes the auto-layer-showing to correctly show Edge.Cuts or
F.CrtYd or B.CrtYd for errors relating to them.
Fixes https://gitlab.com/kicad/code/kicad/issues/6446
1) better load-balancing for deferred zones
2) sort zones by priority before filling
3) retire BOARD::GetZoneList() which had a horrible performance profile
4) implement a zone bounding box cache
5) better checks for IsCancelled() so long fills can be exited
Fixes https://gitlab.com/kicad/code/kicad/issues/5738
If the zone fill failed, then don't add the zone to the
exported VRML because it might not be correct.
Also test that the Python command in DIALOG_SCRIPTING worked.
This dialog actually isn't used anywhere currently, so it
could in theory be removed - but it is simple enough and
it provides a decent testing dialog that it is more work to remove
it.
1) For a while now we've been using a calculated seg count from a given
maxError, and a correction factor to push the radius out so that all
the error is outside the arc/circle. However, the second calculation
(which pre-dates the first) is pretty much just the inverse of the first
(and yields nothing more than maxError back). This is particularly
sub-optimal given the cost of trig functions.
2) There are a lot of old optimizations to reduce segcounts in certain
situations, someting that our error-based calculation compensates for
anyway. (Smaller radii need fewer segments to meet the maxError
condition.) But perhaps more importantly we now surface maxError in the
UI and we don't really want to call it "Max deviation except when it's
not".
3) We were also clamping the segCount twice: once in the calculation
routine and once in most of it's callers. Furthermore, the caller
clamping was inconsistent (both in being done and in the clamping
value). We now clamp only in the calculation routine.
4) There's no reason to use the correction factors in the 3Dviewer;
it's just a visualization and whether the polygonization error is
inside or outside the shape isn't really material.
5) The arc-correction-disabling stuff (used for solder mask layer) was
somewhat fragile in that it depended on the caller to turn it back on
afterwards. It's now only exposed as a RAII object which automatically
cleans up when it goes out of scope.
6) There were also bugs in a couple of the polygonization routines where
we'd accumulate round-off error in adding up the segments and end up with
an overly long last segment (which of course would voilate the error
max). This was the cause of the linked bug and also some issues with vias
that we had fudged in the past with extra clearance.
Fixes https://gitlab.com/kicad/code/kicad/issues/5567
The use of printf, wxLogDebug, and std::err/std::out causes excessive
debugging output which makes finding specific debugging messages more
difficult than it needs to be.
There is still some debugging output in test code that really needs to
be moved into a unit test.
Add debugging output section to the coding policy regarding debugging
output.
This introduces layer handling to a lot of the geometry routines.
Many of them don't do much with it now, but it does help multi-layer
zones and will help when padstacks are implemented.
There were a lot of plotters, exporters, etc. that were rolling their
own implementations.
This also introduces a lazily-built set of SHAPE objects for doing
collision detection and some forms of rendering (and later DRC).
It's currently only supported in the Footprint Editor. It could be
easily added to the board editor (all the code is there), but the board
editor is a little short on room in the drawing tools toolbar.
Remove the CACHE_WRAPPER whose sole purpose was to allow the
cache to be stored in the project, and instead just have the cache
inherit the proper class.
This is the first step to allowing non-segments in the line chain.
External routines cannot be allowed to change the line chain without
going through the internal routines. To accomplish this, we remove the
Vertex() and Point() access routines and only leave the const versions.
Transformations are given for both points as well as the chain itself.
create_vrml_shell() needed the idxSide check but create_vrml_plane only
had an extra variable that wasn't used and so shouldn't be checked.
(cherry picked from commit c9956def36)
In rare cases, the VRML triangulator may claim to work but return empty
vectors. These cases need to be caught before we dereference the vector
elements.
Fixes: lp:1838448
* https://bugs.launchpad.net/kicad/+bug/1838448
(cherry picked from commit 161dc9ce7e)
* Circular gal<->common dependency bites again. Add 'common'
again to the 'kicad' target's link libraries. libgal.a depends
on SHAPE_POLY_SET in common, but common depends on gal. This is
not a real fix, but it unsticks Linux compilations. Fixing the
circular dep is an existing bug: https://bugs.launchpad.net/kicad/+bug/1832229
* Missing LEGACY_HK_NAME for ACT_EndTuning: this was probably accidentally
allowed on some other platform due to different wxString constructors.
On Linux/GCC, it breaks.
* Unused include from /kicad in export_vrml.cpp. This is not findable
on Linux, as pcbnew does not include the right dirs for this to be
found. But it's not used, so just remove it.
Wayne Stambaugh
Jeff Young
Werni
Marek Roszko
jean-pierre charras
Seth Hillbrand
Ian McInerney
Jon Evans
Seth Hillbrand
John Beard