95 lines
3.6 KiB
Plaintext
95 lines
3.6 KiB
Plaintext
;
|
|
; Copyright (c) 2020 Raspberry Pi (Trading) Ltd.
|
|
;
|
|
; SPDX-License-Identifier: BSD-3-Clause
|
|
;
|
|
|
|
.program swo_manchester_tx
|
|
.side_set 1 opt
|
|
|
|
; Transmit one bit every 12 cycles. a '0' is encoded as a high-low sequence
|
|
; (each part lasting half a bit period, or 6 cycles) and a '1' is encoded as a
|
|
; low-high sequence.
|
|
;
|
|
; Side-set bit 0 must be mapped to the GPIO used for TX.
|
|
; Autopull must be enabled -- this program does not care about the threshold.
|
|
; The program starts at the public label 'start'.
|
|
|
|
.wrap_target
|
|
do_1:
|
|
nop side 0 [5] ; Low for 6 cycles (5 delay, +1 for nop)
|
|
jmp get_bit side 1 [3] ; High for 4 cycles. 'get_bit' takes another 2 cycles
|
|
do_0:
|
|
nop side 1 [5] ; Output high for 6 cycles
|
|
nop side 0 [3] ; Output low for 4 cycles
|
|
public start:
|
|
get_bit:
|
|
out x, 1 ; Always shift out one bit from OSR to X, so we can
|
|
jmp !x do_0 ; branch on it. Autopull refills the OSR when empty.
|
|
.wrap
|
|
|
|
% c-sdk {
|
|
static inline void swo_manchester_tx_program_init(PIO pio, uint sm, uint offset, uint pin, float div) {
|
|
pio_sm_set_pins_with_mask(pio, sm, 0, 1u << pin);
|
|
pio_sm_set_consecutive_pindirs(pio, sm, pin, 1, true);
|
|
pio_gpio_init(pio, pin);
|
|
|
|
pio_sm_config c = swo_manchester_tx_program_get_default_config(offset);
|
|
sm_config_set_sideset_pins(&c, pin);
|
|
sm_config_set_out_shift(&c, true, true, 32);
|
|
sm_config_set_fifo_join(&c, PIO_FIFO_JOIN_TX);
|
|
sm_config_set_clkdiv(&c, div);
|
|
pio_sm_init(pio, sm, offset + swo_manchester_tx_offset_start, &c);
|
|
|
|
pio_sm_set_enabled(pio, sm, true);
|
|
}
|
|
%}
|
|
|
|
.program swo_manchester_rx
|
|
|
|
; Assumes line is idle low, first bit is 0
|
|
; One bit is 12 cycles
|
|
; a '0' is encoded as 10
|
|
; a '1' is encoded as 01
|
|
;
|
|
; Both the IN base and the JMP pin mapping must be pointed at the GPIO used for RX.
|
|
; Autopush must be enabled.
|
|
; Before enabling the SM, it should be placed in a 'wait 1, pin` state, so that
|
|
; it will not start sampling until the initial line idle state ends.
|
|
|
|
start_of_0: ; We are 0.25 bits into a 0 - signal is high
|
|
wait 0 pin 0 ; Wait for the 1->0 transition - at this point we are 0.5 into the bit
|
|
in y, 1 [8] ; Emit a 0, sleep 3/4 of a bit
|
|
jmp pin start_of_0 ; If signal is 1 again, it's another 0 bit, otherwise it's a 1
|
|
|
|
.wrap_target
|
|
start_of_1: ; We are 0.25 bits into a 1 - signal is 1
|
|
wait 1 pin 0 ; Wait for the 0->1 transition - at this point we are 0.5 into the bit
|
|
in x, 1 [8] ; Emit a 1, sleep 3/4 of a bit
|
|
jmp pin start_of_0 ; If signal is 0 again, it's another 1 bit otherwise it's a 0
|
|
.wrap
|
|
|
|
% c-sdk {
|
|
static inline void swo_manchester_rx_program_init(PIO pio, uint sm, uint offset, uint pin, float div) {
|
|
pio_sm_set_consecutive_pindirs(pio, sm, pin, 1, false);
|
|
pio_gpio_init(pio, pin);
|
|
|
|
pio_sm_config c = swo_manchester_rx_program_get_default_config(offset);
|
|
sm_config_set_in_pins(&c, pin); // for WAIT
|
|
sm_config_set_jmp_pin(&c, pin); // for JMP
|
|
sm_config_set_in_shift(&c, true, true, 32);
|
|
sm_config_set_fifo_join(&c, PIO_FIFO_JOIN_RX);
|
|
sm_config_set_clkdiv(&c, div);
|
|
pio_sm_init(pio, sm, offset, &c);
|
|
|
|
// X and Y are set to 0 and 1, to conveniently emit these to ISR/FIFO.
|
|
pio_sm_exec(pio, sm, pio_encode_set(pio_x, 1));
|
|
pio_sm_exec(pio, sm, pio_encode_set(pio_y, 0));
|
|
// Assume line is idle low, and first transmitted bit is 0. Put SM in a
|
|
// wait state before enabling. RX will begin once the first 0 symbol is
|
|
// detected.
|
|
pio_sm_exec(pio, sm, pio_encode_wait_pin(1, 0) | pio_encode_delay(2));
|
|
pio_sm_set_enabled(pio, sm, true);
|
|
}
|
|
%}
|