The SAMD09 CPU is used in boards such as the Adafruit Seesaw. It has a
smaller amount of memory and flash than other SAMD ports.
This was tested with an Adafruit Seesaw. These boards come with preloaded
firmware. As a test, the firmware was dumped and flash was erased. Then,
flash was verified to be all zeroes. Finally, the firmware was loaded
back in:
(gdb) p/x *(unsigned int *)0@32
$8 = {0x20000f88, 0x1db, 0x1d1, 0x1d9, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x1d9, 0x0, 0x0, 0xf5, 0x1081, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x0, 0x1d9, 0x1d9, 0x25e9, 0x0,
0x0, 0x1d9, 0x1d9, 0x1d9}
(gdb) dump ihex memory flash.ihex 0 8192
(gdb) mon erase_mass
Erase successful!
(gdb) p/x *(unsigned int *)0@32
$9 = {0xffffffff <repeats 32 times>}
(gdb) load flash.ihex
Loading section .sec1, size 0x2000 lma 0x0
Start address 0x00000000, load size 8192
Transfer rate: 5 KB/sec, 910 bytes/write.
(gdb) p/x *(unsigned int *)0@32
$10 = {0x20000f88, 0x1db, 0x1d1, 0x1d9, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x0, 0x1d9, 0x0, 0x0, 0xf5, 0x1081, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x1d9, 0x0, 0x1d9, 0x1d9, 0x25e9, 0x0,
0x0, 0x1d9, 0x1d9, 0x1d9}
(gdb)
Signed-off-by: Sean Cross <sean@xobs.io>
Various SAMD devices have different amounts of memory. Up until now, all
SAMD devices have had the same amount, and therefore this value was
hardcoded to 32k of RAM and 256k of flash.
Add a parameter to the description field and set it to default to the
previous values. Use this description field when adding memories to the
target definition.
Signed-off-by: Sean Cross <sean@xobs.io>
The variable `start_time` indicates when a CRC32 operation began. This
variable is used to benchmark the speed of the CRC32 function.
Currently, this is tied to `PC_HOSTED`. However, the actual usage is
tied to `DEBUG_WARN`. This means that the variable is undefined when
`DEBUG_WARN` is defined and we're not configured for `PC_HOSTED` mode.
Add macro guards around this variable so that it is defined when
debugging is enabled, rather than only when building on `PC_HOSTED`.
Signed-off-by: Sean Cross <sean@xobs.io>
Workaround for CMSIS-DAP/Bulk debugger orbtrace that returns NO_ACK
with high values of TRNCNT. Perhaps only STM32F767 needs write to DHCSR
with high occupancy to catch the device in a moment not sleeping.
Expect signal integrity errors when using jumper cables. Often probes switch
the SWJ GPIO with highest speed, resulting in possible reflections. Additional
ground wires may help. If there is isolation between probe and targets,
additional ground wires are a must or ground shift will wrack the transfer!
Uwe Bonnes
Piotr Esden-Tempski
Nicolas Schodet
Frank Kunz
Sean Cross
Mark Rages
Koen De Vleeschauwer
fabalthazar