Implemented "locka" command.

cmddb.c

@@ -226,7 +226,14 @@ const struct cmddb_record commands[] = {
 "cgraph <address> <length> [function]\n"
 "    Analyse the range given and produce a call graph. Displays a summary\n"
 "    of all functions if no function address is given.\n"
-	}
+	},
+	{
+		.name = "locka",
+		.func = cmd_locka,
+		.help =
+"locka [set|clear]\n"
+"    Show or change the status of the LOCKA flash write-protect bit.\n"
+	},
 };
 
 int cmddb_get(const char *name, struct cmddb_record *ret)

devcmd.c

@@ -631,3 +631,52 @@ int cmd_break(char **arg)
 
 	return 0;
 }
+
+#define FCTL3		0x012c
+#define FCTL3_LOCKA	0x40
+#define FWKEY		0xa5
+#define FRKEY           0x96
+
+int cmd_locka(char **arg)
+{
+	const char *status = get_arg(arg);
+	int value = 0;
+	uint8_t regval[2];
+
+	if (status) {
+		if (!strcasecmp(status, "set")) {
+			value = FCTL3_LOCKA;
+		} else if (!strcasecmp(status, "clear")) {
+			value = 0;
+		} else {
+			printc_err("locka: unknown action: %s\n", status);
+			return -1;
+		}
+	}
+
+	if (device_default->readmem(device_default, FCTL3, regval, 2) < 0) {
+		printc_err("locka: can't read FCTL3 register\n");
+		return -1;
+	}
+
+	if (regval[1] != FRKEY) {
+		printc_err("warning: locka: read key invalid (got 0x%02x)\n",
+			   regval[1]);
+		return -1;
+	}
+
+	if (status && ((regval[0] & FCTL3_LOCKA) != value)) {
+		printc_dbg("Toggling LOCKA bit\n");
+
+		regval[0] |= FCTL3_LOCKA;
+		regval[1] = FWKEY;
+		if (device_default->writemem(device_default, FCTL3,
+					     regval, 2) < 0) {
+			printc_err("locka: can't write FCTL3 register\n");
+			return -1;
+		}
+	}
+
+	printc("LOCKA is %s\n", (regval[0] & FCTL3_LOCKA) ? "set" : "clear");
+	return 0;
+}

devcmd.h

@@ -34,5 +34,6 @@ int cmd_load(char **arg);
 int cmd_setbreak(char **arg);
 int cmd_delbreak(char **arg);
 int cmd_break(char **arg);
+int cmd_locka(char **arg);
 
 #endif

mspdebug.man

@@ -168,7 +168,7 @@ length (64 bytes) is disassembled and shown.
 
 If symbols are available, then all addresses used as operands are
 translated into \fIsymbol\fR+\fIoffset\fR form.
-.IP "\fBerase\fR [\fIall\fR|\fIsegment\fR] [\fIaddress\fR]"
+.IP "\fBerase\fR [\fBall\fR|\fBsegment\fR] [\fIaddress\fR]"
 Erase the device under test. With no arguments, all code memory is erased
 (but not information or boot memory). With the argument "all", a mass
 erase is performed (the results may depend on the state of the LOCKA
@@ -272,6 +272,17 @@ command is like \fBprog\fR, but it does not load symbols or erase
 the device before programming.
 
 The CPU is reset and halted before and after programming.
+.IP "\fBlocka\fR [\fBset\fR|\fBclear\fR]"
+Show or change the status of the LOCKA bit in the chip's memory
+controller. The LOCKA bit is set on POR and acts as a write-protect bit
+for info segment A. This segment contains factory-configured calibration
+data, and under normal circumstances, should not be changed.
+
+If the LOCKA bit is cleared, erasing the info A segment is possible.
+
+The LOCKA bit also affects the behaviour of the "erase all" command. If
+LOCKA is set (the default), only main memory is erased. If LOCKA is
+cleared, main and information memory are both erased.
 .IP "\fBmd\fR \fIaddress\fR [\fIlength\fR]"
 Read the specified section of device memory and display it as a
 canonical\-style hexdump. Both arguments may be address expressions. If