mspdebug/drivers/fet_error.c

113 lines
4.7 KiB
C

/* MSPDebug - debugging tool for the eZ430
* Copyright (C) 2009, 2010 Daniel Beer
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*
* Various constants and tables come from uif430, written by Robert
* Kavaler (kavaler@diva.com). This is available under the same license
* as this program, from www.relavak.com.
*/
#include "util.h"
/* These messages come from uif430 and from MSP430.DLL V3. */
static const char *error_strings[] =
{
/* 0 */ "No error",
/* 1 */ "Could not initialize device interface",
/* 2 */ "Could not close device interface",
/* 3 */ "Invalid parameter(s)",
/* 4 */ "Could not find device or device not supported",
/* 5 */ "Unknown device",
/* 6 */ "Could not read device memory",
/* 7 */ "Could not write device memory",
/* 8 */ "Could not read device configuration fuses",
/* 9 */ "Incorrectly configured device; device derivative not supported",
/* 10 */ "Could not set device Vcc",
/* 11 */ "Could not reset device",
/* 12 */ "Could not preserve/restore device memory",
/* 13 */ "Could not set device operating frequency",
/* 14 */ "Could not erase device memory",
/* 15 */ "Could not set device breakpoint",
/* 16 */ "Could not single step device",
/* 17 */ "Could not run device (to breakpoint)",
/* 18 */ "Could not determine device state",
/* 19 */ "Could not open Enhanced Emulation Module",
/* 20 */ "Could not read Enhanced Emulation Module register",
/* 21 */ "Could not write Enhanced Emulation Module register",
/* 22 */ "Could not close Enhanced Emulation Module",
/* 23 */ "File open error",
/* 24 */ "File type could not be identified",
/* 25 */ "File end error",
/* 26 */ "File input/output error",
/* 27 */ "File data error",
/* 28 */ "Verification error",
/* 29 */ "Could not blow device security fuse",
/* 30 */ "Security fuse has been blown",
/* 31 */ "Error within Intel hex file",
/* 32 */ "Could not write device register",
/* 33 */ "Could not read device register",
/* 34 */ "Not supported by selected interface or interface is not initialized",
/* 35 */ "Interface communication error",
/* 36 */ "No external power supply detected",
/* 37 */ "External power too low",
/* 38 */ "External power detected",
/* 39 */ "External power too high",
/* 40 */ "Hardware self test error",
/* 41 */ "Fast flash routine experienced a timeout",
/* 42 */ "Could not create thread for polling",
/* 43 */ "Could not initialize Enhanced Emulation Module",
/* 44 */ "Insufficent resources",
/* 45 */ "No clock control emulation on connected device",
/* 46 */ "No state storage buffer implemented on connected device",
/* 47 */ "Could not read trace buffer",
/* 48 */ "Enable the variable watch function",
/* 49 */ "No trigger sequencer implemented on connected device",
/* 50 */ "Could not read sequencer state - sequencer is disabled",
/* 51 */ "Could not remove trigger - used in sequencer",
/* 52 */ "Could not set combination - trigger is used in sequencer",
/* 53 */ "System Protection Module A is enabled - device locked",
/* 54 */ "Invalid SPMA key was passed to the target device - device locked",
/* 55 */ "Device does not accept any further SPMA keys - device locked",
/* 56 */ "MSP-FET430UIF Firmware erased - bootloader active",
/* 57 */ "Could not find MSP-FET430UIF on specified COM port",
/* 58 */ "MSP-FET430UIF is already in use",
/* 59 */ "EEM polling thread is already active",
/* 60 */ "Could not terminate EEM polling thread",
/* 61 */ "Could not unlock BSL memory segments",
/* 62 */ "Could not perform access, BSL memory segments are protected",
/* 63 */ "Another device as selected was found",
/* 64 */ "Could not enable JTAG wrong password",
/* 65 */ "Only one UIF must be connected during update to v3",
/* 66 */ "CDC-USB-FET driver was not installed, please install the driver",
/* 67 */ "Manual reboot of USB-FET needed! PLEASE unplug and reconnect your USB-FET!",
/* 68 */ "Internal error",
/* 69 */ "Invalid error number",
};
const char *fet_error(int code)
{
if (code < 0 || code >= ARRAY_LEN(error_strings))
return "Unknown error";
return error_strings[code];
}