Introduce the HAVE_SERIAL_COMM identifier, which gets derived from, but
need not be identical to the HAVE_LIBSERIALPORT condition.
Derive the NEED_SERIAL automake condition from the general availability
of serial communication not the specific libserialport library.
Adjust source code references. Stick with HAVE_LIBSERIALPORT where the
specific library is meant, but switch to HAVE_SERIAL_COMM where the
availability of serial communication in general is meant.
Align the scaling items such that all numbers are aligned. Drop unneeded
"prefixes" for the 2nd display's tables, the main and sub displays already
have their individual tables which reside in their respective groups.
Introduce the dmm/eev121gw.c source file with parse routines for the
EEVblog 121GW meter's 19-bytes binary packets. Get the values and MQ
properties of the device's several displays (main, sub, bar) in several
individual parse calls.
This commit introduces initial support for the device. Some of the modes
and features are untested, as are some of the device's ranges.
Optionally create multiple analog channels in serial-dmm's scan()
routine. Allow the meters' parse routines to fill in more than one
analog value from the inspection of a single packet.
Use "large" (4 times 14 bytes) packets for the Metex M-3860M and the
PeakTech 4390A meters, and have those large packets parsed by wrapping
the routines for regular 14-byte Metex packets, and sending four values
to the session bus after reception of one large packet.
Thanks to Frank Stettner <frank-stettner@gmx.net> for testing and
fixing the initial implementation of this extension.
Few DMM drivers already did it. This commit adjusts the remaining DMM
drivers, to set the "DC" flag for measurements in diode mode.
This fixes bug #144.
Although I don't have the hardware to test, the nature of the change and
the arrangement of driver code suggests it's good. When a meter already
communicated the "DC" status, the change does nothing and won't harm.
The change ensures "DC" is flagged for those meters which previously
didn't, which is desirable.
Some drivers used locale dependent functions for converting strings
to float/double values. These functions fail when the decimal mark
is a "," in the locale settings but the string contains a ".".
This fixes bug #1064.
The resistance values of some DMMs were incorrectly reported due to a
missing factor of 10 in the calculations.
Tested on Voltcraft VC-920/VC-940 and Tenma 72-9380A/72-7730/72-7732.
Old:
ut71x: Applying exponent -12, new value is 0.000000.
P1: 1.500 nF AUTO
P1: 1.500 nF AUTO
New:
ut71x: Applying exponent -12, new value is 1.5e-09.
P1: 1.500 nF AUTO
P1: 1.500 nF AUTO
This fixes bug #700.
Replace a C library strcspn(3) call with the more portable glib
g_strstr_len(3) routine. This is possible since a single separator
is searched for, no actual "set of characters" is involved.
As a byproduct, this eliminates a "late" reference to 'cnt' at the
bottom of the routine, after the value was assigned in a rather distant
location at the top of the routine. The cost of strlen() should be
acceptable for a buffer with a single digit total length.
Replace C language string operations with their glib incarnations for
improved portability. Prefer a common sigrok float conversion routine
over a DIY implementation.
The specific packet layout puts constraints on the parse logic (case
sensitive comparison, order of comparison). Fix a comment that made no
sense before, and better reflect that there are two constraints.
Introduce an asycii.c source file (modelled after metex14.c) which
implements support for the 16-byte protocol of the ASYC-II multimeter
chipset (RX only, when the PRINT button was pressed).
There is no status bit for RMS. We know about RMS if certain modes are
active. So, drop this superfluous variable.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The primary display is the power factor, the secondary is the frequency.
This got mixed up, so change the order. We also need to fix the
conversion factor.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
is_power_apparent_power is index 0 of function 0x39, so it is better to
process it first and the later indices after that (we need to add
another one with a different patch later).
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing showed that AC current needs to be handled different from DC.
Note that ACA is still untested because of limited testing equipment.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It was confusing to see the display value (5 digits) printed in debug
output as a float. Print it the same way as shown on the real device,
without comma, of course.
This also allows to simplify the code a little.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This fixes parts of bug #423.
The list of fixed warnings:
src/output/srzip.c:285:3: warning: Value stored to 'ret' is never read
ret = zip_append(o, logic->data, logic->unitsize, logic->length);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/scpi/scpi.c:610:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/scpi/scpi.c:667:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/dmm/vc870.c:410:2: warning: Value stored to 'info_local' is never read
info_local = (struct vc870_info *)info;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/conrad-digi-35-cpu/api.c:130:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/fx2lafw/api.c:658:2: warning: Value stored to 'timeout' is never read
timeout = fx2lafw_get_timeout(devc);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/protocol.c:941:3: warning: Value stored to 'retc' is never read
retc = SR_ERR_ARG;
^ ~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/api.c:168:2: warning: Value stored to 'model' is never read
model = METRAHIT_NONE;
^ ~~~~~~~~~~~~~
src/hardware/ikalogic-scanalogic2/api.c:325:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/openbench-logic-sniffer/api.c:185:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/rigol-ds/api.c:813:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/scpi-pps/api.c:405:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/yokogawa-dlm/api.c:239:2: warning: Value stored to 'ret' is never read
ret = SR_ERR_NA;
^ ~~~~~~~~~
Gerhard Sittig
Vitaliy Vorobyov
Uwe Hermann
Matthias Schulz
Adrian Stratulat
Mandl
Frank Stettner
Aurelien Jacobs
Wolfram Sang
Matthieu Gaillet