Bump the number of supported logic channels from 8 to 128. This is
mostly motivated to test the 64 channels limit which some of the
components/subprojects of the sigrok project might have (input/output
modules, user interfaces).
Only automatically enable the first 8 of the 128 total logic channels,
i.e. default to the previous behaviour. Prepare to only enable part of
the set of analog channels, but stick with their being active by default
as well.
Factor out the choice for the default logic pattern, too. This allows
for easier adjustment of the default configuration, when settings are
concentrated in a single spot.
Extend the demo driver, add another waveform choice for logic channels.
Create a "cable squid" logo representation which occupies a large number
of channels.
This pattern occupies 128x128 pixels. Unlike the 'sigrok' pattern it
gets repeated when more channels are involved, but is not shifted in the
repetition.
The handling of the digital channels for this series is somewhere
between that of the DS1000D series (PROTOCOL_V2) and the MSO1000Z
(PROTOCOL_V4).
The :LA command set is similar to that of V4, but the LA data has to be
requested with :WAV:SOUR:LA and arrives in interleaved form like V2.
None of these changes should affect other models. They only affect the
case of PROTOCOL_V3 with digital channels, which occurs only for the
MSO2000A series.
Fixes#933.
We'd already had this problem elsewhere and thus have this wrapper function
that does this where necessary. It just wasn't in use on these two call sites,
which was causing timing problems when used over tcp-raw or VXI transports.
With trigger enabled, and with PulseView, a second (or more) acquisition
starts immediately instead of blocking. It's mandatory to try several times
to have a correct behavior.
According to http://mygizmos.org/ols/Logic-Sniffer-FPGA-Spec.pdf section 2.3.1
p.8, the Openbench Logic Sniffer must be reset before each arm command.
This fixes bug #809.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Openbench Logic Sniffer reset is a little more complex than a simple send.
To avoid code duplication, this patch adds a new function dedicated to
this task.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
This changes the fx2lafw code to only enable the wide_sampling (16bit)
method, if at least one of the higher eight channels is enabled. This
has the benefit, that we can use higher samplerates on 16bit LA
devices if we use only the first eight channels.
The wide sampling is also enabled if we have one or more analog
channels.
Signed-off-by: Jan Losinski <losinski@wh2.tu-dresden.de>
devc->step is not reset on acquistion start, so acquisition
starts with a different value every time. Thats annoying when
using the demo driver to debug sigrok, so lets make sure that
it's reset to 0.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
sr_period_string takes the frequency as its argument, i.e. the reciprocal
of the timebase. Obviously this will not work for frequencies less than
1Hz / timebases greater than 1 second, but at least is correct for all
other available timebases.
sr_period_string takes the frequency as its argument, i.e. the reciprocal
of the timebase. Obviously this will not work for frequencies less than
1Hz / timebases greater than 1 second, but at least is correct for all
other available timebases.
Phrase the logic which checks the use of analog channels and digital
pods in more generic terms. Place a comment about the contraints' being
potentially dependent on the specific HMO model. This implementation
should lend itself better to future adjustment (HMO1002?).
An internal libsigrok implementation detail prevents partial submission
of logic data for different channel groups in multiple calls. Instead
one logic packet needs to be sent in a single call, which combines data
for all channels.
Introduce a logic data storage which folds samples from several channel
groups that were received at different points in time into a combined
memory layout of larger unitsize. Stick with the former shortcut of
passing on the input bytes directly when only the first digital pod is
used during acquisition.
This change correctly maps data from the second pod to channels D8-D15.
Uwe Hermann
Gerhard Sittig
Martin Ling
Johannes Römer
Gwenhael Goavec-Merou
Marc Schink
Bert Vermeulen
Jan Losinski
Soeren Apel
Matthieu Guillaumin
Sven Schnelle
Vlad Ivanov
Sebastian Tabares Amaya
Aurelien Jacobs
Stefan Brüns