This makes the code shorter, simpler and more consistent, and also
ensures that the (same) debug messages are always emitted and the
packet.payload field is consistently set to NULL always, etc.
The USBee AX hardware needs a sampling clock that is lower than
the 30MHz or 48MHz that the FX2 has to offer. This flag will enable
clocking via the CTL2 pin that is an even divisor of the main clock.
The driver did not look at the mq_flags provided with the
SR_CONF_MEASURED_QUANTITY key, and it defaulted to DC measurements.
Use the second member of the tuple provided by the config key, which
represents the flags for the measurement, and set the instrument's
measurement mode accordingly.
On the high-end bench multimeters, resistance can be measured with a
kelvin connection as well as the more common two wire method. Provide
a flag which can indicate if four-wire mode is used.
Due to a PEBKAC error, after the last sample was sent, a new
measurement was triggered, but its value was never sent down the
session bus. This is easily fixed by incrementing devc->num_samples
right after a measurement is sent instead of when a measurement is
retriggered.
g_variant_print() allocates memory during call. Save the pointer
so that it can be free'd afterwards.
==10048== 16 bytes in 1 blocks are definitely lost in loss record 17 of 37
==10048== at 0x4C2DEAE: realloc (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
==10048== by 0x536C85D: g_realloc (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x53877C6: ??? (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x5388B60: g_string_append_vprintf (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x5388D83: g_string_append_printf (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x539D034: g_variant_print_string (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x539C92C: g_variant_print (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x4E5F713: log_key (hwdriver.c:597)
==10048== by 0x4E5FCD5: sr_config_set (hwdriver.c:752)
==10048== by 0x408C1A: run_session (session.c:661)
==10048== by 0x404FC5: main (main.c:267)
==10048==
==10048== 16 bytes in 1 blocks are definitely lost in loss record 18 of 37
==10048== at 0x4C2DEAE: realloc (in /usr/lib/valgrind/vgpreload_memcheck-amd64-linux.so)
==10048== by 0x536C85D: g_realloc (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x53877C6: ??? (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x5388B60: g_string_append_vprintf (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x5388D83: g_string_append_printf (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x539D034: g_variant_print_string (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x539C92C: g_variant_print (in /lib/x86_64-linux-gnu/libglib-2.0.so.0.4400.1)
==10048== by 0x4E5F713: log_key (hwdriver.c:597)
==10048== by 0x4E5FBDD: sr_config_get (hwdriver.c:709)
==10048== by 0x4080D7: datafeed_in (session.c:196)
==10048== by 0x4E5D47E: sr_session_send (session.c:1192)
==10048== by 0x4E62682: std_session_send_df_header (std.c:101)
Using non power of 2 sizes causes the driver to not work on OS X.
Depending on the usb transfer mode the buffer sizes will map
perfectly to the underlying transport protocol.
scpi_serial generate an POLLIN event after the requested data is returned
by the instrument. For USBTMC it is necessary to
1. send an REQUEST_DEV_DEP_MSG_IN request
2. submit an USB bulk read transfer asynchronously.
Using the synchronous libusb_bulk_read() does not generate an POLLIN event.
Solving this properly needs major surgery in spci_usbtmc_libusb.
While some transports add a terminating (carriagereturn+)linefeed
unconditionally, the USBTMC transport does not. At least the R&S HMO1002
requires the linefeed and locks up otherwise. Fixes bug #784.
This changes the TCP and VXI transport from CR+LF to LF only.
Also fixes a possible memory leak for VXI, where the temporary command
buffer was not freed in case of a write error.
According to USBTMC usb488 subclass spec, wValue hast to be 0 for both
LOCAL_LOCKOUT and GO_TO_LOCAL. At least required for R&S HMO1002, the
bad request results in a STALL. Fixes bug #783.
After acquisition start, DSLogic stores samples in memory, and when done it
sends a USB packet with the trigger position.
This initial fillup can take some time. If the user requests a session stop
in between, the USB transfer is cancelled and the session hangs because it
is not closed properly.
This commit manages this case and closes the session properly when
acquisition is stopped by the user.
Signed-off-by: Diego F. Asanza <f.asanza@gmail.com>
According to the infos I have, VCD files should be plain ASCII, but we
got report of a version adding a UTF8 BOM at the beginning of the file,
so we need to skip it.
This fixes bug #755.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For some reason, uploading the FPGA binary into DSLogic in small chunks
does not work. In this commit, the whole binary image is loaded into memory
and transfer is done in one chunk.
Furthermore, the FPGA configuration structure was not initialized
properly. This was changed with the initialization values taken from the
original DSLogic software.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
Certain output modules do not understand double-precision data.
Although we need double precision to represent the full resolution
of 7.5 digit readings, temporarily convert data to single precision
so that the output modules understand it. While the reasing might be
off by a few counts, we ensure the output modules do not display
completely bogus data.
For details, see bug #779.
KNOWN ISSUES:
- When sampling with 100 NPLC, the poll function will timeout a few
times before the first sample is acquired. Increasing the timeout
passed to sr_scpi_source_add() will cause all the other commands to
be processed slowly, producing a sampling rate of about one sample
every ten seconds.
- Support for plug-in cards (44491A and 44492A) is not implemented.
- Support for AC, AC+DC and four-wire resistance measurements is not
implemented.
- Support for configuring the frequency measurement source is not
implemented.
Uwe Hermann
Benjamin Larsson
Joel Holdsworth
Alexandru Gagniuc
Sergey Alirzaev
Markus Siegert
Stefan Brüns
Diego F. Asanza
Andrew Bradford
EJ
Wolfram Sang
Soeren Apel