* Delete Single Pad Net option does not delete the net if a zone use this net (i.e. is attached to this pad).
* pcb_parser accept now negative netcodes in zones (can happen with old files, which previously could crash Pcbnew)
* pcb_parser accept now files with incorrect or missing net count (can happen with old files, which previously could crash Pcbnew)
* if a zone has a non-existent net name it now keep this net name, and DRC detect it (previously, the net name was lost, and the DRC did not tected this issue).
* Drc test: now detect a "dead" net, i.e. a net with 0 pads, but still used by a zone. It happens easily after a schematic modification, when a net disappears or is renamed.
(for instance, when a footprint from the currently edited board is loaded in the footprint editor, and when the board is cleared or reloaded)
In footprint editor, the net names are no more shown od modifiable (becuase the footprint editor does not know anything about net names.
This change should allow the changes planned in pcbnew.
Renamed BOARD_CONNECTED_ITEM::SetNet() -> SetNetCode()
Added BOARD_CONNECTED_ITEM::GetNet() for accessing NETINFO_ITEM* of a given item.
Fixed module editor crash when launched to edit a module from a PCB.
Replaced some BOARD::FindNet( item->GetNet() ) calls with BOARD_CONNECTED_ITEM::GetNet().
Now, nets are saved with consecutive net codes (both modern & legacy plugins).
Zones are saved together with their nets, without depending on the fact if there are any pads with such net. Therefore validation of zone net names was removed (pcbnew/class_board.cpp).
Performed tests:
- Changed a pad's net name from empty to existent - ok, name was changed.
- Changed a pad's net name from empty to nonexistent - ok, error message is displayed, net name stays empty.
- Changed a pad's net name from existent to empty - ok, net name became empty
- Changed a pad's net name from existent to nonexistent - ok, error message is displayed, net name is not changed.
- Drawn a zone that belongs to a net, then modified schematics so the net does not exist anymore. After reloading the net list, all pads/tracks are updated. Zones still belongs to the net that does not exist in the schematic (but still exists in .kicad_pcb file). After running DRC, the zone becomes not filled.
- Undo & redo affects assignment of a polygon to a specific net (you may change net of a polygon, refill it and undo/redo the changes).
- KiCad s-expr & legacy, Eagle, P-CAD boards seem to load without any problem (they also contain correct net names assigned to the appropriate pads). All types of board file formats were loaded, then saved in sexpr format and reopened with a KiCad built from the master branch (without my modifications).
- A few boards were also saved using the legacy format and were opened with the master KiCad without any issues.
- Change a net name for a pad, restore with undo/redo - ok
- Remove everything, restore with undo - ok
- Remove everything, reload netlist - ok
Differences observed between files saved by the master branch KiCad and this one:
- list of nets are not saved in any particular order, so net codes may differ
- the default net class does not contain the unconnected net
GetNet() refers to the net code stored in the NETINFO_ITEM. SetNet() finds an appropriate NETINFO_ITEM and uses it.
Removing GetNet() & SetNet() (and the whole net code idea) requires too many changes in the code (~250 references to the mentioned functions).
BOARD_CONNECTED_ITEMs by default get a pointer to NETINFO_ITEM that stores unconnected items. This requires for all BOARD_CONNECTED_ITEMs to have a parent (so BOARD* is accessible). The only orphaned item is BOARD_DESIGN_SETTINGS::m_Pad_Master, but it does not cause any issues so far.
Items that do not have access to a BOARD (do not have set parents) and therefore cannot get net assigned, by default get const static NETINFO_LIST::ORPHANED.
Performed tests:
- loaded .kicad_pcb, KiCad legacy board, Eagle 6.0 board, P-CAD board - all ok
- load a simple project, reload netlist after changing connections in eeschema - ok
- save & reload a board - ok, but still contain empty nets
- remove everything, restore with undo - ok
- remove everything, reload netlist - ok
- changing net names (all possibilites: empty->existing, empty->not existing, existing->empty, existing->not existing) - all ok
- zones: when net is changed to a net that does not have any nodes besides the zone itself, it does not get filled
Net codes are updated upon net list update. (BOARD::ReplaceNetlist())
Added in some places (mostly class_board.cpp) pad->SetNet() calls to synchronize net codes.
On creation of NETINFO_LIST, the first NETINFO_ITEM is added (the unconnected items net).
Removed COMPONENT_NET::m_netNumber, as it was not used anywhere.
Added an assert to D_PAD::GetNetname(), checking if net code and net name is consistent for unconnected pads. Added an assert for NETINFO_LIST::AppendNet() to assure that appended nets are unique.
It seems that at this point:
- Updating net lists works fine. The only difference between the file ouput is that after changes it contains empty nets as well.
- Nets are not saved in the lexical order. Still, net names and net codes are properly assigned to all items in the .kicad_pcb file. It is going to be addressed in the next commit. I believe it should not create any problems, as pads are sorted by their net names anyway (NETINFO_LIST::buildPadsFullList())
Performed tests:
- Created a blank PCB, saved as pic_programmer.kicad_pcb (from demos folder). Updated net lists. .kicad_pcb file (comparing to the results from master branch) differ with net order (as mentioned before), net codes and timestamps.
- Removed some of components from the above .kicad_pcb file and updated net lists. Modules reappeared. .kicad_pcb file differs in the same way as described above.
- Trying to change a pad net name (via properties dialog) results in assert being fired. It is done on purpose (as there is a call to GetNetname() and net name and net code do not match). This will not happen after the next commit.
- Prepared a simple project (starting with schematics). Imported net list, changed schematic, reimported net list - changes are applied.
- Eagle & KiCad legacy boards seem to load without any problem.
NETINFO_ITEM::m_Net and NETINFO_ITEM::m_Netname are const.
Changes to be verified:
- pcbnew/minimun_spanning_tree.cpp: It segfaults is m_Size == 0
- pcbnew/exporters/export_gencad.cpp: I removed the SetNetname() call, as it changes only the unconnected net and in the next line it returns if the net is unconnected. Still, I wonder if name for the unconnected net matters. What about tests that check if a net name is empty to decide if it is unconnected net or not.
* Create separate NETLIST object to hold contents of netlist files.
* Read entire netlist and footprint link files before making applying
changes to board.
* Add BOARD::ReplaceNetlist() function to eliminate the calls between the
NETLIST_READER, PCB_EDIT_FRAME, and BOARD objects.
* Change placement of new components below the center of the current board
or in the center of the page if the BOARD is empty.
* Add dry run option to netlist dialog to print changes to message control
without making changes.
* Add button to netlist dialog to allow saving contents of message control
to a file.
* Eliminate the need to compile netlist_reader_*.cpp in both CvPcb and Pcbnew.
* Add netlist_reader_*.cpp to the pcbcommon library.
* Remove redundant load component link file code from CvPcb.
* Modify CvPcb new to work with the new NETLIST_READER object.
* Add compare() function and < and == operators to FPID object.
* Add REPORTER class to hide an underlying string writing implementation for
use in low level objects. Thank you Dick for the idea.
* Lots of minor coding policy, Doxygen comment, and missing license fixes.
* Improve MSG_PANEL_ITEM to handle message panel information.
* Create containers for passing message panel items between objects and
the message panel.
* Rename EDA_ITEM::DisplayInfo to EDA_ITEM::GetMsgPanelInfo.
* Remove all direct manipulation of EDA_DRAW_FRAME from all objects derived
from EDA_ITEM.
* Correct all user strings and comments for the correct capitalization of
application names according to JP. They are KiCad, Pcbnew, CvPcb,
Eeschema, and GerbView.
* Add a note the the user interface policy about the correct capitalization.
* All header files used to create the PCB common library now compile as
stand alone code. This prevents the need to define them in a specific
order to make source code compile properly. It should also now be
possible to relocate the source code to build the common PCB library
to a separate folder.
* Move schematic wire and bus break code into schematic screen object.
* Move schematic test for dangling ends into schematic screen object.
* Remove left over debugging output in schematic screen object.
* Remove unused file eeschema/cleanup.cpp.
* Fix bug in schematic line object hit test algorithm.
* Fix a string concatenation compile error added in r2752.
* Rename class WinEDA_BasicFrame to EDA_BASE_FRAME.
* Rename class WinEDA_DrawFrame to EDA_DRAW_FRAME.
* Rename class WinEDA_DrawPanel to EDA_DRAW_PANEL.
Dick Hollenbeck
jean-pierre charras
Maciej Suminski
Wayne Stambaugh
Lorenzo Marcantonio
Marco Mattila
charras