We were running into various corner conditions where a tool's event
loop would exit while the tool was still active, or the tool would
get popped while we were still in the event loop. (A lot of these
had to do with the POINT_EDITOR's, but not all of them.)
The new architecture:
1) tools always do a Push()/Pop()
2) everyone is responsible for their own pops; no more stack-clearing
on a cancel
3) CancelInteractive events go to all tools to facilitate (2)
This checks the movement against a maximum value that would place the
selection outside of the valid area for the footprint or board.
Fixes: lp:1833478
* https://bugs.launchpad.net/kicad/+bug/1833478
(cherry picked from commit 845833e8fd)
It's a bit of a hack because they're statically initialized and
so we can't make use of the _() macro. We do still want it in the
code, however, because the string harvesting is based off of it.
Fixes: lp:1833000
* https://bugs.launchpad.net/kicad/+bug/1833000
Prevents certain edit tools from handling the action unless the cursor
remains inside the selection bounding box.
For now this is a UX test but the behavior may be expanded into Eeschema
as well.
Fixes: lp:1827242
* https://bugs.launchpad.net/kicad/+bug/1827242
Mouse capture end is called by some actions such as save board. This
resets the cursor image but doesn't change the current tool. Resetting
the cursor image during action prevents this.
(cherry picked from commit 35e87128f5)
Fixes: lp:1831888
* https://bugs.launchpad.net/kicad/+bug/1831888
The dynamic ratsnest is shown while moving items but this needs to be
hidden after cancelling. Previously this was handled by the
SelectionClear event but we've changed this to (correctly) keep the
previous selection when canceling.
Fixes: lp:1831350
* https://bugs.launchpad.net/kicad/+bug/1831350
This behavior existed in 5.0.x but did not properly exit the edit tool
in 5.1. This removes stops the edit tool when we begin dragging a track
using the interactive router.
Fixes: lp:1820312
* https://bugs.launchpad.net/kicad/+bug/1820312
Choosing the drag origin should not be dependent on the snap settings in
pcbnew. Snap settings are sensible when you are designating a target
only. Additionally, when dragging a module, we do not want the
footprint's pads to be used as targets for snapping.
Fixes: lp:1814402
* https://bugs.launchpad.net/kicad/+bug/1814402
There is some odd interaction in the default copy constructor for
TOOL_EVENT using boost::optional under gcc. Avoid this by explicitly
constructing the event needed for cut
Fixes: lp:1812848
* https://bugs.launchpad.net/kicad/+bug/1812848
The local/dynamic ratsnest needs to calculate on a per-pad basis as the
module is always listed as having a visible ratsnest. This fixes the
finalized ratsnest viewed when routing as well as the show local
ratsnest regression.
Fixes: lp:1811010
* https://bugs.launchpad.net/kicad/+bug/1811010
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
Distinguish between the snap-from and snap-to items. Previously, we
used the SELECTED or DRAGGED flags but the flagging arcitecture was
inherently fragile. This specifies items directly that should not be
used as snap targets.
Fixes: lp:1802795
* https://bugs.launchpad.net/kicad/+bug/1802795
Filtering based on selection ignores the use case where we are measuring
to a selected item. This utilizes the dragged flag to prevent snapping
based on the current state of the item drag.
Fixes: lp:1801089
* https://bugs.launchpad.net/kicad/+bug/1801089
When drawing the crosshair should track the element while the mouse
provides the position to calculate the next snap.
Fixes: lp:1796524
* https://bugs.launchpad.net/kicad/+bug/1796524
When requesting to move a footprint based on the pad, the pad layers
should determine the snapping. This extracts layers from the selected
pad before allowing the filtering for locked pads
Fixes: lp:1787627
* https://bugs.launchpad.net/kicad/+bug/1787627
We had been deselecting items after calling edits to be safe in case the
item was deleted/exchanged by the edit. The item pointer itself remains
valid even when deleting as it is assigned to the undo stack. But it
should not remain visible or selected on the schematic if it is removed.
This tests for removed items by checking whether it (in the case of
first-level BOARD_ITEMS) or its parent (in the case of footprint item
components) remain in the view list after editing. If they are still in
the view list, then we re-select them.
( cherry-picked from 2c6d0ffe2 )
Fixes: lp:1765774
* https://bugs.launchpad.net/kicad/+bug/1765774
Fixes: lp:1775946
* https://bugs.launchpad.net/kicad/+bug/1775946
Also fixes a bug where nets wouldn't get changed because the
pads weren't changed and so the pad nets would propagate and
wipe out the changed nets on the tracks.
Also includes warning dialogs that pad nets will be changed if the
track nets are.
Fixes: lp:1779854
* https://bugs.launchpad.net/kicad/+bug/1779854
Use standard Magnetize() to handle grid and magnetic pads.
Use the standard menu from PCB_TOOL. Delegating the menu to
the SELECTION_TOOL just caused grief.
Also brings clients (such as Position Relative To) into line,
and implements better Cancel behaviour.
Also improves visibility of modal status messages:
- moves Select Anchor message from status bar to popup
- moves Select Reference message from dialog to popup
Fixes: lp:1786727
* https://bugs.launchpad.net/kicad/+bug/1786727
Also fixes some interactivity issues in the microwave tools around
single-click tools that have initial properties dialogs. Those
need to act kind of like a hybrid between single-click and two-click
tools.
Fixes: lp:1751381
* https://bugs.launchpad.net/kicad/+bug/1751381
When changing elements in the module editor, each element shares the
same parent. Undo commits store a copy of the parent as it existed
before the change. For footprints with many elements, this creates
large, slow undo commits as a copy of the full footprint is stored for
each element being edited.
This keeps a single copy of the footprint in the undo stack per edit.
Fixes: lp:1780526
* https://bugs.launchpad.net/kicad/+bug/1780526
This not only reduces the number of different mechanisms, but
will also reduce (yet again) the number of Clarify Selection
pop-ups (because the CLIENT_SELECTION_FILTER runs before the
pop-up, while SanitizePads ran after it).
Fixes: lp:1710451
* https://bugs.launchpad.net/kicad/+bug/1710451
(cherry picked from commit e50a993)
The general idea is to support user-units inheritance. The
UNIT_BINDER allows wrapped controls to inherit units from their
parent dialog, while KEYWAY_HOLDER and DIALOG_SHIM allow child
KEYWAY_HOLDERs or DIALOG_SHIMs to inherit units from their
parent.
The GetUserUnits() method signature has to move to KEYWAY_HOLDER
rather than KEYWAY_PLAYER (where it makes more sense) as it’s the
only common ancestor of KEYWAY_PLAYER and DIALOG_SHIM.
As long as we'll be using the UNIT_BINDER more widely, it also
makes sense to move evaluation and validation into it.
This commit also provides eeschema’s DIALOG_LABEL_EDITOR and
pcbnew’s DIALOG_TRACK_VIA_PROPERTIES and DIALOG_SET_GRID as
models of how to use the new user-units inheritance, eval, and
validation.
Fixes: lp:593795
* https://bugs.launchpad.net/kicad/+bug/593795
(cherry picked from commit c8bc53e)
There's no risk in measuring an empty footprint but there's no benefit
either. This matches the measure tool to the other, deactivated
footprint tools.
New items just being placed on the board are still temporary. Although
we can modify their orientations/positions, we can't stage these changes
for undo/redo without corrupting the undo stack.
Fixes: lp:1776312
* https://bugs.launchpad.net/kicad/+bug/1776312
Also fixes a bug where a FOOTPRINT_EDIT_FRAME was being passed
in to a PCB_EDIT_FRAME.
Also tidies up Modedit settings handling for settings which can't
be edited in Modedit's preferences dialog. They're now copied
from Pcbnew.
Fixes: lp:1768477
* https://bugs.launchpad.net/kicad/+bug/1768477
This really needs to get put into the VIEW_CONTROLS for all the
tools, but that's probably a bit too risky for 5.0 at this
point.
Fixes: lp:1766547
* https://bugs.launchpad.net/kicad/+bug/1766547
When multiple cut commands were issued, the cut command handler would
restart multiple times and keep running until the handler that was
invoked first finishes. As all handlers kept a selection copy, they
would try to save the deleted items to the clipboard resulting in a
crash.
Fixes: lp:1761221
* https://bugs.launchpad.net/kicad/+bug/1761221
CTRL+{X,C,V} used to be handled both by the legacy hotkey system that
generated ID_EDIT_{CUT,COPY,PASTE} wxCommandEvent, and the Tool Framework
hotkey system.
Fixes: lp:1749549
* https://bugs.launchpad.net/kicad/+bug/1749549
Tools preserve their state between runs, so it could happen that
activating a tool restores the state when autopanning is enabled, even
though it should not be.
Commit complementary to 4f0c9b6b. In case there were multiple tracks
under the cursor, disambiguation was shown twice because
SELECTION_TOOL::selectConnection() cleared the selection and requested
it again.
Also adds Cancel context menu items for Place Footprint,
Place Target, Place Drill Origin and Place Grid Origin tools,
as well as the standard Zoom and Grid choices.
Removes the Paste context menu item from the Place Drill
and Place Grid Origin tools.
Fixes: lp:1568396
* https://bugs.launchpad.net/kicad/+bug/1568396
Second disambiguation menu was caused by another call to
SELECTION_TOOL::RequestSelection() meant to get the list of
connected tracks. When there were only footprints under the cursor,
it asked the user again to pick an item to remove.
Fixes: lp:1748521
* https://bugs.launchpad.net/kicad/+bug/1748521
This commit also adds a no-selection-mode, which allows the user
to specify what gets update (through the various match modes).
The no-selection-mode is accessed via the Edit menu, although
it could also be applied to the context menu.
Fixes: lp:1466857
* https://bugs.launchpad.net/kicad/+bug/1466857
Some actions, such as select trivial connection, don't need the
user to choose which trace at a corner to start from -- either
one will do. Same for moving a simple trace corner.
Likewise, Edit in Footprint Editor shouldn't ask if you mean the
footprint or the pad. Obviously it's the footprint.
This change adds a CLIENT_SELECTION_FILTER which allows clients
to do tool- or action-specific filtering of the selection before
the disambiguation menu is run.
It also removes some tool- and action-specific code which was
in the selection_tool and shouldn't have been.
Fixes: lp:1708869
* https://bugs.launchpad.net/kicad/+bug/1708869
Opening Properties dialog normally does not ask the user to confirm the
action, even for locked items. The exception was a case when there was
nothing selected and Properties dialog was invoked via its hot key -
then SELECTION_TOOL::RequestSelection() tried to get the item under the
cursor, verifying the lock flag.
Fixes: lp:1734537
* https://bugs.launchpad.net/kicad/+bug/1734537
A change in commit 5731000135 caused kicad to stop allowing users
to move items like footprints, arcs and lines using anchors other
than the center point.
This was caused by the new code that stores reference points for
clipboard pasting, a call to updateModificationPoint() prevented
some old code paths from executing, which caused the selection to
snap into the cursor, always using the center anchor.
This fix moves the call within the if-cases that need it, and adds
a ClearReferencePoint call when the selection is "dropped" to allow
the user to grab the same selection again from a different anchor.
Fixes: lp:1722512
* https://bugs.launchpad.net/kicad/+bug/1722512
- renamed connectivity.[h|cpp] to connectivity_data [.h|.cpp] so that the file name matches the main class name.
- GetNetItems() now returns a vector instead of a list
- fixed netcode propagation bug
- factored out EDIT_TOOL::m_offset, now selection offset is stored in SELECTION class
- added VECTOR2I-based Move/Flip/Rotate methods in BOARD_ITEM
- added selection of reference point
- added snapping when pasting
- some minor code refactoring
- disabled pasting between footprint and pcb editors due to model incompatibility
- support for background color setting
- removed several global config settings (such as g_Drc_On)
- wrapped most of global config settings in PCB_GENERAL_SETTINGS class
- reorganized PCB general options dialog to clearly mark which options concern only the legacy canvas
- new GAL feature for legacy users: double-click (or E) to change track width available as an option.
Fixes: lp:1530543
* https://bugs.launchpad.net/kicad/+bug/1530543
Fixes: lp:1707145
* https://bugs.launchpad.net/kicad/+bug/1707145
- added TOOL_INTERACTIVE::resetTransitions()
- made protected and moved TOOL_BASE::setTransitions() to TOOL_INTERACTIVE
- TOOL_MANAGER calls TOOL_INTERACTIVE::resetTransitions() instead of
setTransitions()
This patch does the following:
* extracts a method to determine the anchor point of the move
* improves the logic of the anchor point determination for selections of multiple objects which do not contain footprints
This patch adds a radiobox to allow the user to select a reference point for
the move. The additional options are: User Origin (set with <space>),
Grid Origin and Sheet Origin (effectively making it an absolute coordinate).
A checkbox is added (where it makes sense) to allow overriding which point
within the component is put on top of the designated coordinate.
Fixes: lp:1460460
* https://bugs.launchpad.net/kicad/+bug/1460460
These were backwards since internal angles are CCW due to the inverted Y
axis.
The hotkeys have NOT changed. This means 'R' is now clockwise and
'Shift+R' is anti-clockwise. This is the same as EEschema, but not the
same as Legacy mode.
This uses the two-point geometry manager to split the logic of the ruler
geometry and the preview item display. This allows the ruler to use that
manager's angle snap feature.
This allows to measure between features on a PCB. It uses a preview
EDA_ITEM in common, but due to the use of the IDs, it's currently
Pcbnew/Modedit only.
This also adds several "utils" for graphical functons useful when
drawing preview items on GAL canvases.
Fixes: lp:1467313
* https://bugs.launchpad.net/kicad/+bug/1467313
- The tools can now specify if the items in the selection must be editable/
deletable. This is groundwork to be able to select/delete DRC markers, which can't
otherwise be edited.
- Fixed disappearing of selected objects
SELECTION now holds EDA_ITEMs not BOARD_ITEMs so various places had to
change to casting the selected items to BOARD_ITEMs.
Fixed compilation warnings on clang (Tom)
Some grid/zoom tools are left in PCBNEW_CONTROL because they currently
depend on Pcbnew-specific class members. Once refactoring is done to
make it possible to use all zoom and grid controls outside of pcbnew,
these last tools can be moved to common to match their ACTIONs.
New virtual class ACTIONS is added as a member to EDA_DRAW_FRAME so
that the TOOL_DISPATCHER can have access to the appropriate derived
version of TranslateLegacyId()
This commit wires up the as-yet-unused "remove alternate" tool action
and uses it to select copper connections (normally 'U') before deleting
segments.
THis also reverses the sense of Delete and Backspace (Delete used to be
'remove' and Backpace was 'remove alt', now it is reversed). This means
that backspace is the key that removes a segment and Delete removes the
track. This is the same as legacy behaviour. Other delete actions are,
for now, the same between Delete and Backspace.
Fixes: lp:1517213
* https://bugs.launchpad.net/kicad/+bug/1517213
Provide a visual feedback to the user how each rotation
will affect the routing by immediately reflecting the
change in ratsnest orientation.
Signed-off-by: Aurabindo J <mail@aurabindo.in>
Fixes: lp:1663488
* https://bugs.launchpad.net/kicad/+bug/1663488
This makes "rotate" into two separate TOOL_EVENTs, which each have a
"multiplier" parameter.
Also added is a namespace for 'free functions' that use TOOL_EVENT
public interfaces (perhaps with other inputs too) to centralise some
decision-making and calculations.
Fixes: lp:1660731
* https://bugs.launchpad.net/kicad/+bug/1660731
In principle, this patch reverts 2eefa117. The difference is removal of
one unused method (SELECTION::clear) and fixing hidden overloaded
virtual methods warnings.
Fixes: lp:1657569
* https://bugs.launchpad.net/kicad/+bug/1657569
There used to be a number of TOOL_ACTIONs that had entries both in
SetTransitions() and the event loop, which seemed redundant and
troublesome.
Now it is not necessary anymore, transitions setup is enough to execute
associated actions.
The problem with simple deleting VIEW_ITEM_DATA upon VIEW_ITEM removal was
caused by the default copy constructors that copied pointers.
Once a copy of an item was destroyed, the VIEW_ITEM_DATA has been
destroyed, effectively invalidating m_viewPrivData for the other item.
This means that non-top-level tools, for example EDIT_TOOL and
PCB_EDITOR_CONTROL can submit their own menus to the top-level tool's
TOOL_MENU, which will then retain a reference to it and make it
available for the CONTEXT_MENU that is shown.
- Finalize transition to BOARD_COMMIT (removed all remaining uses of PICKED_ITEMS_LIST) and implicit view/ratsnest updates
- Simplified SELECTION class, it now can be directly added to a VIEW
- Removed unnecesary casts and templates
- Introduced C++11 features (range based for, lambdas) where they improve code readability
- Added non-undoable COMMITs, which can be used to propagate change notifications to interested listeners (e.g. ratsnest/view)
Following rev 6627 (git 2777182), if a non-duplicatable item was the object of
a Duplicate action, the original item would be picked up, potentially
misleading the user into thinking something was actually duplicated.
* No initial copied object changed (this was a serious bug to modify these objects. Previous version modified references and other texts using a very stupid algorithm).
It also fixes bug 1549231
* only new pads are numbered (therefore renumbering is used only in footprint editor)
* remove not working and useless feature in circular array: now only use number for pads (others options using alphabetical letters are removed: did not work corectly, and were useless)
* a more clear option is used to choose if the pads are numbered from a choosen value, or from the first avaible value
* Adding a warning messsage if a parameter is incorrect.
Modedit, GAL mode: fix a crash when a duplicated area includes the ref or value fields.
Add missing bitmap for pad enumerate.
fix bad flag for Portuguese language.
Fix a few typo in messages.
Text arrays can now use "%s" as a placeholder to be substituted with the array index.
Also expand menu options for move exact, arrays and duplicate.
Minor fixes for arrays - use proper unit parsing, add numbering start for circular arrays
Add circle radius indicator to array dialogue
- Removed the friends MODULE and FOOTPRINT_EDIT_FRAME from TEXTE_MODULE
(as in the @todo comment)
- Refactored the Rotate/Flip/Mirror for text in modules into the
TEXTE_MODULE class itself (members RotateWithModule, FlipWithModule,
MirrorWithModule)
- New behaviour in coloring text on screen: reference and value still
take the color from the MOD_TEXT_FR_VISIBLE and MOD_TEXT_BK_VISIBLE
visibles; other text takes the color of the layer containing it
(except when hidden, obviously) but still get its visibility
controlled by those visibles (probably the most intuitive and useful
behaviour)
- Still need to decide: should text on a layer be hidden when the layer
is? Probably yes (still to be implemented);
- Some comment fixed and many cast converted to static_cast
Modification point is selected basing on the number of selected items.
Rotation angle setting (Preferences->General) is taken into account while rotating.
- pcbnew.InteractiveSelection.Single for selecting a single item
- pcbnew.InteractiveSelection.Clear for clearing the selection
Made SELECTION_TOOL::clearSelection private.
Fixed crashes of ratsnest when a pointer for an item has changed after undo/redo operations.
Vias are properly removed from ratsnest (pcbnew/class_board.cpp).
RN_DATA::Update()/AddSimple() take BOARD_ITEM* as the parameter (instead of being split to versions with BOARD_CONNECTED_ITEM* and MODULE*), to make the code look clearer.
Modifications done using the EDIT_TOOL are saved using the default KiCad's undo buffer.
If there is only one item selected, info about the item is displayed in the bottom status bar.
Jeff Young
Seth Hillbrand
Ian McInerney
jean-pierre charras
Tomasz Włostowski
Maciej Suminski
Jon Evans
Jose I Romero
Kristoffer Ödmark
Michael Geselbracht
Fabrizio Tappero
Robbert Lagerweij
Russell Oliver
Oliver Walters
John Beard
Aurabindo J
Maciej Suminski
Simon Richter
decimad
Chris Pavlina
Simon Wells
Lorenzo Marcantonio