1845d71f00
jtag_scan: Deliver full idcode to the handler.
2021-08-15 16:43:29 +02:00
c7bc4b6a5d
Bug fix in Flash erase function for LPC MCUs.
2021-08-13 16:18:53 +02:00
72bd825a60
Add support for NXP LPC11xx XL series, add 'readuid' command for some MCUs of the LPC11xx series where it was missing; add comments mapping Device IDs to part descriptions.
2021-07-31 16:08:34 +02:00
0c63903071
adiv5: Recover from bad AP access.
...
E.g. AP1 on a STM32WLE5 points to a ROM table, but access to the ROM table
via AP1 hangs forever.
- Substantial reduce timeout when wait for a response. Valid access should
succeed fast.
- Abort AP access to free DP for other accesses
- Don't throw exception, only set dp->fault
- React on higher level
2021-07-15 15:06:54 +02:00
5ea01030e2
Add nRF51 command for (only) erasing the UICR registers
...
Original implementation by: Benjamin Vedder <benjamin@vedder.se>
2021-06-07 13:50:36 +02:00
4b8c4990dc
Fix warning about unused variable in adiv5.c
...
This happens if the platform has debugging support but debugging
is not enabled.
2021-06-03 12:56:41 +02:00
711a87f7ba
Fix some warnings when compiling with -Wshadow
...
There are still a few more places that would need to be corrected
before -Wshadow could be added by default.
2021-06-03 12:55:28 +02:00
891633322a
lpc: Care for protected pages on LPC80x devices.
2021-06-01 16:23:19 +02:00
f7b4697280
lpc11xx/lpc8c04: Do not expose two top system flash sectors.
2021-06-01 16:23:19 +02:00
42ebcac329
efm32_devices: Rearrange struct efm32_device_t to save flash space.
2021-06-01 16:23:19 +02:00
21a702dc1e
lpc: More verbosity and more definitions
2021-06-01 16:23:19 +02:00
87acd99fe4
cortexm: For Cortex-M0+ devices, probe also for lpc11 to detect LPC80 #884
2021-05-18 12:24:00 +02:00
517d5b5b31
rp: Show spinner only when called from monitor command.
2021-05-16 11:26:14 +02:00
0ab10fee0b
rp: Increase timeout for flash_range_program
...
If the RP2040 is using the ring oscilator (ROSC) rather than the crystal
oscilator (XOSC) then flashing program will take much longer. As the XOSC is not
enabled at boot we should not assume it will be enabled before the debugger is
connected (or indeed at all), thus should use the longer timeout during load
commands.
2021-05-16 11:26:14 +02:00
ff30259354
rp: Add more debug logging during flash
2021-05-16 11:26:14 +02:00
e453740aca
rp: Increase spinner timeout to 500ms
...
Increasing spinner timeout to 500 means `tc_printf` is not called during
the `_flash_range_erase`. This is important as `_flash_range_erase` is
used when loading. This fixes the issue:
https://github.com/blacksphere/blackmagic/issues/875
Also adding spinner timeout counter to reduce bus traffic.
2021-05-16 11:26:14 +02:00
67c9003522
rp: Flush cache after erase and write
...
The RP2040 datasheet suggests that _flash_flush_cache and _flash_enter_cmd_xip
should be called after erasing and writing to flash.
2021-05-16 11:26:14 +02:00
f880734050
Fix compiling for native probe
2021-05-16 11:26:14 +02:00
e4421799ba
More header cleanup
2021-05-15 12:54:51 +02:00
f9414d5826
cmsis-dap: Handle ADI DP22 devices on probes not multidrop capable.
2021-04-26 18:18:18 +02:00
1f67bab475
nxpke04: Move unsafe_enables to target bool union.
2021-04-25 16:03:23 +02:00
f87dff8d83
kinetis: Remove static variables, add word union to target_s.
...
Add a word union to target structure to hold a single word variable.
2021-04-25 16:03:23 +02:00
ac7c1057cc
efm32/samd/samx5x: Remove static allocates strings. Allocate in priv_storage.
...
Static allocated variables in the different targets eat up common RAM and
will collide in chains with multiple similar targets.
2021-04-25 16:03:23 +02:00
cddf02f174
samx5: Verbose error reports on protected devices.
2021-04-25 16:03:23 +02:00
8c8aa980cf
adiv5: Detect unprotected SAMD5x only once
2021-04-25 16:02:20 +02:00
1b26ff560d
rp.c: Add reset_usb_boot as monitor command
2021-04-24 14:48:58 +02:00
52bffa70cf
rp: Handle flash.
...
- Beware, after reset, only a valid flash payload get mapped to XIP!
Only 0 is read from flash when flash image is not valid
2021-04-21 21:55:03 +02:00
2b0e255c40
cortexm: timeout and debug for run_stub()
2021-04-21 21:50:38 +02:00
61efe26348
swdp_scan: Break infinite loop after Dormant->SWD transition.
2021-04-21 21:50:38 +02:00
fa5e69e3be
RP 2040: Special handling for rescue DP
...
As the rescue DP provided no AP, trigger the reset with attach().
However attach will indicate failure also reset/halt has succeeded.
2021-04-21 21:50:38 +02:00
ea92c8b8c8
cmsis-dap: Allow to use adiv5_swdp_scan.
2021-04-21 21:50:38 +02:00
23f942ac8c
Raspberry RP2040: Recognize. No flash handling yet.
2021-04-21 21:50:35 +02:00
04d1c9805b
swd: Remove swd_proc and swdptap.h.
2021-04-21 21:50:04 +02:00
b6fbf86743
Extend ADIv5_DP_t for low level routines needed for multi-drop.
...
Will replace swd_proc
2021-04-21 21:50:04 +02:00
5abb288c7a
hosted: Provide the DP functions in swd_proc.
2021-04-21 21:50:04 +02:00
fa561c8d66
adiv5_swdp: Starting point to handle multi-drop
...
- RP2040 show both DPs
- Multidrop test with STM32L552 and STM32H745 allows selection
with "-m 0x4500041" (H7), "-m 1" (L552) or "-m 0x01002927" (RP2040)
2021-04-21 21:50:04 +02:00
be3bfc48a8
cortexm: M33 has up to 8 hardware breakpoints
2021-04-21 21:22:59 +02:00
b1ac4187b9
Fix some formatting strings for 32-bit compile
2021-04-21 21:22:59 +02:00
beaccf2714
target: stm32l4: add support for STM32WLxx
...
This adds support for the STM32WL series in stm32l4.c. These parts have
the same flash registers layout as the L4 series, but a different base.
Since there are already two sets of registers in this target file, this
adds support for register maps that can be customized for each device
ID.
2021-04-20 18:42:36 +02:00
f55ad67b1b
adiv5: catch timeout on adiv5_ap_read_id and abort
...
This adds a TRY_CATCH around the adiv5_ap_read_id() in
adiv5_component_probe() and resets the DP when that happens.
It seems like the STM32WLE5 comes with the AP of the inactive core
enabled in a way that does not make it detectable, and the current code
times out and leaves the whole device hanging.
Catching the timeout and calling adiv5_dp_abort() seems to restore the
device to a useable state.
Tested on Seed LoRa-E5 (STM32E5JC).
2021-04-19 16:57:13 +02:00
d6b24c00c8
Fixed STM32G43x/G44x option bytes support
...
Previously took L4 values so FLASH_SEC1R was not applied
2021-04-17 14:44:30 +02:00
99f9557cc0
Support for STM32G49x/G4Ax (category 4)
2021-04-17 14:44:30 +02:00
c85c946ce3
PRIx32 fix
2021-04-17 14:44:30 +02:00
a6a8606edb
STM32L55: Detect, memory map, read and flash write. Options handling missing.
...
Only non-secure states considered!
2021-04-04 17:26:31 +02:00
6d6cfd6c98
Comprehensive STM32G03/4/5/6/7/8/B/C driver
2021-03-29 21:42:40 +02:00
58f153e12b
cortexm: Always halt and release reset before romtable scan
...
Only release from halt once after romtable scan
Should fix #836 .
2021-03-26 17:43:11 +01:00
a025c9a7bd
Revert "stm32f1: On ST parts there is no need to read IDCODE again."
...
Romtable partno is not unique for devices, e.g. in STM32F0
This reverts commit f89b07d892
2021-03-26 17:35:00 +01:00
f89b07d892
stm32f1: On ST parts there is no need to read IDCODE again.
...
IDCODE is already known from the Romtable
Probably this has the same effect as #836
2021-03-12 20:45:34 +01:00
7859a2aabd
adiv5_swd: Factor out creation of packet request.
2021-03-06 13:30:09 +01:00
cfb784d428
adiv5: Fix comments and debug output
2021-03-05 16:49:19 +01:00
Uwe Bonnes
Thiadmer Riemersma
Björn Mellström
James Turton
Fabio Baltieri
fabalthazar