Most drivers have a forward declaration to their sr_dev_driver struct at
the beginning of the driver file. This is due to historic reasons and often
no longer required. So remove all the unnecessary forward declarations.
Some drivers still require the forward declaration, but only reference the
driver struct from within the driver scan() callback. Since the driver
struct is passed to the scan callback replace the references to the global
variable with the local parameter. In some cases this requires adding the
parameter to some of the helper functions that are called from the scan()
callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
To capture more than 16MSamples the hardware run length encoding option
must be enabled, or captured data present errors.
RLE encoding/decoding is done in hardware. Data streamed to the USB interface
is not encoded.
This commit enables RLE encoding for captures longer than 16MSamples.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
This commit expands support for acquisition using an external clock,
now allowing the user to select the clock edge.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
For low sampling speeds (up to 25MHz) DSLogic offers a streaming mode where
samples are sent directly to the USB interface, like a fx2lafw device.
For high sampling speeds (up to 400MHz) only buffer mode is supported.
This commit allows the user to set which mode should be used. The configuration
is done by using SR_CONF_CONTINUOUS.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
The DSLogic provides two FPGA images: one for 3.3V and the other for 5V logic.
The DSLogic Pro allows to set an arbitrary voltage threshold via USB command.
This commit adds support for the DSLogic to load the FPGA image according to
an user-selectable voltage threshold.
For the DSLogic Pro, one of two fixed voltage thresholds are set, depending on
the user-selected value.
Tested with DSLogic and DSLogic Pro.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
Tested-by: Andrew Bradford <andrew@bradfordembedded.com>
This commit implements DSLogic trigger functionality.
The following triggers are working:
- trigger on rising edge
- trigger on falling edge
- trigger on any edge
- trigger on logic one
- trigger on logic zero
Pre-trigger capture ratio is also working.
Signed-off-by: Diego Asanza <f.asanza@gmail.com>
Tested-by: Andrew Bradford <andrew@bradfordembedded.com>
The demo device has support for specifying the number of analog and logic
channels it should have. Currently this does not work correctly if one of
them is set to zero. Being able to set the number of channels to zero for
one of the channel types is quite useful for corner case testing though.
Make the following modifications to handle it correctly:
1) If the channel count is zero no channel group for that channel type
should be created since a channel group needs at least one channel.
2) Drop the check if logic_unitsize is less or equal to zero in
prepare_data() since this condition will always be true if the number of
logic channels is zero and it is not possible to create a demo device with
only analog channels.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Now that the signature of std_init() matches that of the driver init()
callback we can remove all wrapper functions around std_init() and use it
directly as the init() callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
std_init() checks if the pass in struct sr_dev_driver is non-NULL and
prints a error message and returns an error if it is NULL.
std_init() is exclusively called from driver init() callbacks for which the
core already checks if the struct sr_dev_driver is non-NULL before invoking
the callback. This means the check in std_init() will always evaluate to
false. So drop this check.
This also means that the prefix parameter that was used in the error
message is no longer needed and can be removed from the function signature.
Doing so will make the std_init() function signature identical to the
init() callback signature which will allow to directly use it as such.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The std_init() callback has the order of the first two paramters opposite
to the init() callback. This is primarily due to historical development.
Since the std_init() function is usually called from a driver's init()
callback aligning the order will allow direct register pass through rather
than having to swap them around. It also allow to eventually use the
std_init() function directly as the init() callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The zeroplus-logic-cube driver uses libusb_get_device_list() but neglects
to call the matching libusb_device_list_free() on the error path. This will
leak the memory allocated for the list as well as all the devices.
To address the issue use sr_usb_open() instead of open-coding its
functionality. sr_usb_open() correctly handles freeing the device list.
The issue was discovered using the following coccinelle semantic patch:
// <smpl>
@@
identifier devlist;
expression ctx, ret;
statement S;
@@
(
libusb_get_device_list(ctx, &devlist);
|
ret = libusb_get_device_list(ctx, &devlist);
if (ret < 0) S
)
... when != libusb_free_device_list(devlist, ...)
*return ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The victor-dmm driver uses libusb_get_device_list() but neglects to call
the matching libusb_device_list_free() on the error path of libusb_open().
This will leak the memory allocated for the list as well as all the
devices.
To address the issue use sr_usb_open() instead of open-coding its
functionality. sr_usb_open() correctly handles freeing the device list.
The issue was discovered using the following coccinelle semantic patch:
// <smpl>
@@
identifier devlist;
expression ctx, ret;
statement S;
@@
(
libusb_get_device_list(ctx, &devlist);
|
ret = libusb_get_device_list(ctx, &devlist);
if (ret < 0) S
)
... when != libusb_free_device_list(devlist, ...)
*return ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The testo driver uses libusb_get_device_list() but neglects to call the
matching libusb_device_list_free() on the error path. This will leak the
memory allocated for the list as well as all the devices.
To address the issue use sr_usb_open() instead of open-coding its
functionality. sr_usb_open() correctly handles freeing the device list.
The issue was discovered using the following coccinelle semantic patch:
// <smpl>
@@
identifier devlist;
expression ctx, ret;
statement S;
@@
(
libusb_get_device_list(ctx, &devlist);
|
ret = libusb_get_device_list(ctx, &devlist);
if (ret < 0) S
)
... when != libusb_free_device_list(devlist, ...)
*return ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
lascar_scan() calls libusb_get_device_list() but never the matching
libusb_free_device_list(). This will leak the memory allocated for the
device list as well as all the devices. To fix this add the missing
libusb_free_device_list().
While we are at it also make sure to handle errors returned by
libusb_get_device_list().
The issue was discovered using the following coccinelle semantic patch:
// <smpl>
@@
identifier devlist;
expression ctx, ret;
statement S;
@@
(
libusb_get_device_list(ctx, &devlist);
|
ret = libusb_get_device_list(ctx, &devlist);
if (ret < 0) S
)
... when != libusb_free_device_list(devlist, ...)
*return ...;
// </smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Some drivers check in some of their driver callbacks if the driver has been
initialized and return an error if it has not.
For the scan() callback the sigrok core checks if the driver has been
initialized and if not returns an error. So it is not possible that the
scan() callback gets called if the driver is not initialized. Without the
scan() callback succeeding it is not possible to get a reference to a
device which is associated with the driver, so it is not possible that any
of the device specific callbacks is called without the driver first being
initialized either.
In conclusion these checks are not necessary since they never evaluate to
true and can be dropped. If they should ever become necessary they should
be done in the sigrok core so all drivers and all callbacks are equally
handled.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Lars-Peter Clausen
Uwe Hermann
Stefan Brüns
Diego Asanza
Bert Vermeulen