The dynamic ratsnest is shown while moving items but this needs to be
hidden after cancelling. Previously this was handled by the
SelectionClear event but we've changed this to (correctly) keep the
previous selection when canceling.
Fixes: lp:1831350
* https://bugs.launchpad.net/kicad/+bug/1831350
When using "Place Text" the crosshair was freezing if cancelled before
placing text.
After the crosshair freezes, the next uses of the "Place Text" or
"Add Dimension" caused the crosshair to jump to the screen location
where the previously the crosshair was frozen.
Cancelling the "Add Dimension" caused the crosshair to jump to the
screen location where the crosshair was when cancelled on the next use
of the "Place Text" or "Add Dimension".
Fixes: lp:1822578
* https://bugs.launchpad.net/kicad/+bug/1822578
It was confusing that the primary frames registered their tools
differently than the other frames. In addition, since the other
frames also added their own tools, foo_actions::RegisterAllTools()
didn't really register all tool but rather those used by the
principal frame (PCB_EDIT_FRAME, SCH_EDIT_FRAME, etc.)
Give the user the option of cancelling a file open if there are
segment zones; otherwise they're converted to polygon fills.
Fixes: lp:1823087
* https://bugs.launchpad.net/kicad/+bug/1823087
This behavior existed in 5.0.x but did not properly exit the edit tool
in 5.1. This removes stops the edit tool when we begin dragging a track
using the interactive router.
Fixes: lp:1820312
* https://bugs.launchpad.net/kicad/+bug/1820312
Reverting changes causes the item to become invalid. This can cause
issues when we have dangling pointers for the VIEW routines left over.
Until we implement a method of passing the reverted element back up to
the calling routine, we need to remove the selection for each Revert()
call.
Fixes: lp:1821909
* https://bugs.launchpad.net/kicad/+bug/1821909
When removing a point from the polygon, the vertex is removed before it
is tested for validity. If it fails validation, the edit is reverted
and the point count doesn't change, so the view update only modifies the
existing points. But the revert may also have changed the shared
pointer to the point array, invalidating the view's copy.
Fixes: lp:1821909
* https://bugs.launchpad.net/kicad/+bug/1821909
A zone refill display progress bar is shown when deselecting the zone after geometry changes.
However, on Linux, there are some artifact between the progress bar refresh and the board view refresh:
the filled areas are incorrectly shown: the insulated islands remain displayed,
although they are removed from the actual filled areas list
So it is disabled until a fix is found.
Previously, in many cases the selected zone was refilled on exit selection, even if the zone was not modified.
This is annoying, because the zone fill can be really time consuming, and cannot be called without a good reason.
Now the refilling is made only if a zone parameter is actually modified.
Highlight connections is meant to show the copper connections on a
board. We remove the non-copper pads from our selection when attempting
to source the net for highlighting.
Fixes: lp:1815898
* https://bugs.launchpad.net/kicad/+bug/1815898
Choosing the drag origin should not be dependent on the snap settings in
pcbnew. Snap settings are sensible when you are designating a target
only. Additionally, when dragging a module, we do not want the
footprint's pads to be used as targets for snapping.
Fixes: lp:1814402
* https://bugs.launchpad.net/kicad/+bug/1814402
Snapping to item options were partially disconnected when unifying
framework. This re-attaches the options and adds the additional option
for graphical items.
Fixes: lp:1801377
* https://bugs.launchpad.net/kicad/+bug/1801377
Rather than selecting an arbitrary track to snap, we select the closest
track to our point, allowing the via to be placed along the full track
length.
Fixes: lp:1813324
* https://bugs.launchpad.net/kicad/+bug/1813324
Prior to placing the via, we check if the resulting via will pass too
close to different nets on different layers.
Fixes: lp:1718827
* https://bugs.launchpad.net/kicad/+bug/1718827
When creating the zone cutout, we delete the old zone and add a new one
with each cutout. This requires resetting the source zone and clearing
our previous selection if we would like to continue using the cutout
tool on the new zone.
Fixes: lp:1812339
* https://bugs.launchpad.net/kicad/+bug/1812339
There is some odd interaction in the default copy constructor for
TOOL_EVENT using boost::optional under gcc. Avoid this by explicitly
constructing the event needed for cut
Fixes: lp:1812848
* https://bugs.launchpad.net/kicad/+bug/1812848
- Added ignore netcode option to CONNECTIVITY_DATA::GetConnectedItems()
- PlaceModule() now ensures the module added to the board (and thus to the connectivity database) has correct bounding box necessary for R-trees to work
- Use recursive connected pad search so that the new net is propagated to all pads
Fixes: lp:1787961
* https://bugs.launchpad.net/kicad/+bug/1787961
When renumbering pads, you can click on a pad the second time to restore
the pad to its original value. This did not allow a user to then place
the removed number on the correct pad (assuming a mistake). This commit
ensures that removed pad numbers are remembered and allow the user to
place in the correct pad.
The local/dynamic ratsnest needs to calculate on a per-pad basis as the
module is always listed as having a visible ratsnest. This fixes the
finalized ratsnest viewed when routing as well as the show local
ratsnest regression.
Fixes: lp:1811010
* https://bugs.launchpad.net/kicad/+bug/1811010
Frame refresh in wxWidgets sets the focus back to indeterminate state
and prevents hotkey action until the focus is captured again. Using
canvas update is the correct method to update the canvas display after
modifying zones/similar
Fixes: lp:1810993
* https://bugs.launchpad.net/kicad/+bug/1810993
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Checks for ratsnest enabled prior to calculating and displaying the
local/dynamic ratsnest. Calls the ratsnest clear from selection clear
Notably, it appears that the tool actions do not chain transitions for
the same event. So only a single action (first specified) will be
executed when an event fires unless the actions are executed by separate
tools.
Fixes: lp:1809752
* https://bugs.launchpad.net/kicad/+bug/1809752
This fixes the handling of align/distribute tool when called on locked
items. Locked items cannot be moved but they may be used for the target
of an align/distribute operation.
Fixes: lp:1808238
* https://bugs.launchpad.net/kicad/+bug/1808238
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
Graphic lines and polygons are drawn to fit specific areas for which it
is helpful to have the endpoint controlled by the cursor even when
constraining the angle.
Fixes: lp:1805502
* https://bugs.launchpad.net/kicad/+bug/1805502
* Do not compile dxf old files.
* import gfx, gal mode: make absolute placement working.
* Import gfx in legacy canvas: use it and make interactive placement working
* Take imported line width in account. Ensure DXF line thickness is OK.
* handling empty files in legacy mode.
The client filter might add items in the case where locked pads are
filtered. We need to handle this case when requesting selection by
adding new items to the m_selection
Fixes: lp:1802686
* https://bugs.launchpad.net/kicad/+bug/1802686
When we draw a path, we usually want to close the path when clicking on
the end of another line. This uses grid helper to ensure this
progression happens as expected.
When updating the status of the ratsnest, we mark its target layer as
dirty to ensure the revised data are used to draw/clear the ratsnest
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit 50eedcf0b3)
The ratsnest layer needs to be always enabled in GAL rather than taken
from the board settings. This also adds a finalize handler to the
picker tool that allows a picker-caller to perform a specific action
when the picker tool exits. In this case, we use it to clear the local
ratsnest selections back to the default.
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit c0d9b9ab81)
When the local ratsnest tool is used, it should toggle the state based
on the global ratsnest visibility. After changing state, the layer
cache is marked as well.
Possibly related to lp:1800301
(cherry picked from commit 22fbf30f22)
Distinguish between the snap-from and snap-to items. Previously, we
used the SELECTED or DRAGGED flags but the flagging arcitecture was
inherently fragile. This specifies items directly that should not be
used as snap targets.
Fixes: lp:1802795
* https://bugs.launchpad.net/kicad/+bug/1802795
Filtering based on selection ignores the use case where we are measuring
to a selected item. This utilizes the dragged flag to prevent snapping
based on the current state of the item drag.
Fixes: lp:1801089
* https://bugs.launchpad.net/kicad/+bug/1801089
When snapping, we should allow any point identified as a snappable
point. The additional consideration for corners might be used for
alignment in the future.
Fixes: lp:1802741
* https://bugs.launchpad.net/kicad/+bug/1802741
Separate out zone edges (which are quite specific, and should
win over most other things) from zone fills (which are pretty
generic and should only be considered when there's nothing else).
Also excludes zone fills when the zones aren't being shown as
filled.
When processing the selection filter, items were deselected before being
reselected after passing through the filter. This adjusts the logic to
only deselect those items that are filtered out.
Refactor the polygon event loop into its parent function to allow access
to the params structure. Active layer now updates the drawing layer for
add/cutout zones.
Fixes: lp:1797483
* https://bugs.launchpad.net/kicad/+bug/1797483
When using the board edit, align tool automatically moved footprints
instead of pads but distribute tool did not. This standardizes the
behavior.
Fixes: lp:1796997
* https://bugs.launchpad.net/kicad/+bug/1796997
If the user is carefully selecting the zone edge, we do not filter the
zone preemptively from our disambiguation list in the same manner as we
do for selecting on zone copper.
Fixes: lp:1796719
* https://bugs.launchpad.net/kicad/+bug/1796719
Disabling the grid should leave the snapping in place. But our disabler
returned the current point as closest, effectively always ensuring the
cursor position was the closest snap. This only uses grid when
requested.
This is temporary until we figure out a way to do multiple constraint
handling in GRID_HELPER or the EC_* class. This will work as long as
the EC constraint helper places the endpoint on either the primary or
aux grid.
Fixes: lp:1796540
* https://bugs.launchpad.net/kicad/+bug/1796540
Get the board settings when changing the drawing layer. These include
default line thickness that should be updated.
Fixes: lp:1796489
* https://bugs.launchpad.net/kicad/+bug/1796489
When drawing the crosshair should track the element while the mouse
provides the position to calculate the next snap.
Fixes: lp:1796524
* https://bugs.launchpad.net/kicad/+bug/1796524
The dimension tool is used to measure physical dimensions on the board
therefore it should be able to snap to any other object, not just those
on its own layer set as is the case for other items.
This also deals with a corner snap case for constraints by first
snapping, then constraining, then aligning to grid. This ensures OoO
for alignment from least to most constraining.
When considering potential targets for snap points, we need to exclude
the currently selected item as this will mean that we always snap to
ourselves when editing an existing item.
Fixes: lp:1796507
* https://bugs.launchpad.net/kicad/+bug/1796507
When drawing segments, the segment will be NULL'd after committing, at
which point we lost our snap layer. Choosing snap layers from the
current drawing layer is a more robust method.
Fixes: lp:1796467
* https://bugs.launchpad.net/kicad/+bug/1796467
Deselection by clicking on a zone makes working with plane zones easier
by allowing the selected item to de-selected by clicking on a zone.
Once the selection is cleared, the zone may be re-selected as normal.
Clicking on non-zone items while a separate item is selected will still
select the new non-zone item without requiring a second click.
This shows the snap indicator even when the item we are snapping to
occurs on a grid point, giving the user an indication that the point is
correctly connected.
Many items require precise, non-grid movement. Adding the ability to
flag a non-grid option will permit this behavior.
This is a required precursor commit to fixing lp:1738818 and lp:1771683
The computeAnchors function is used to find best drag locations for
items being moved. All movable PCB items should be handled.
Fixes: lp:1794304
* https://bugs.launchpad.net/kicad/+bug/1794304
When requesting to move a footprint based on the pad, the pad layers
should determine the snapping. This extracts layers from the selected
pad before allowing the filtering for locked pads
Fixes: lp:1787627
* https://bugs.launchpad.net/kicad/+bug/1787627
Since we are handling snapping in the grid helper, we don't need to
enable it in the cursor position return. This allows the grid helper to
use the frame position while optionally snapping to segments.
Put the cursor and pan control TOOL_ACTIONs in ACTION,
and refer to them in that way.
The handlers are currently identical in Pcbnew and Cvpcb,
and Gerbview (and all canvases) can benefit from them as well
if they are in libcommon. Also saves duplicated code.
Fixes: lp:1795855
* https://bugs.launchpad.net/kicad/+bug/1795855
This ensures that when starting to draw a zone or graphic element, the
preview is drawn in the same color/on the same layer as the element that
will be created. Previously, beginning a graphic polygon while a copper
layer was active would result in the preview being drawn in the color of
the active copper layer.
Polygon corners were enabled in the footprint editor but the logic
didn't extend to the board editor. This revises the logic to look for
DRAWSEGMENTs and only reference the PCB_MODULE_EDGE_T where needed to
create a new segment in the footprint.
Fixes: lp:1782966
* https://bugs.launchpad.net/kicad/+bug/1782966
Allows selection of polygons and zones by their visible area. Will only
select polygons/filled areas when they are unobstructed by other
elements in the footprint/pcb. Also adds a "skip heuristics" modifier
key for clicking (ALT) that allows the full disambiguation list to be
displayed without removing less-likely elements. This dovetails the
zone/polygon selection as it allows selecting even when areas a fully
overlapped.
Fixes: lp:1753153
* https://bugs.launchpad.net/kicad/+bug/1753153
SEGZONEs are no longer created by pcbnew but may exist in older boards.
This allows deleting the old fills in a manner similar to the deletion
in Legacy canvas.
Fixes: lp:1794571
* https://bugs.launchpad.net/kicad/+bug/1794571
SEGZONE types were confusingly named PCB_ZONE_T. Zones in pcbnew are
now _only_ PCB_ZONE_AREA_T, so we name segzone types PCB_SEGZONE_T to be
clear.
This also removes processing of the SEGZONEs from connectivity
calculations.
Unselecting performs two functions: unselecting and unhighlighting.
Some items may be deselected but still live in the temporary highlighted
layer (e.g. selecting a footprint and exchanging it). Since there is no
harm in unselecting an unselected item, we can allow it to proceed
without the check.
Jeff Young
jean-pierre charras
Seth Hillbrand
Ian McInerney
Jon Evans
Martin McNamara
MaPePeR
Tomasz Włostowski
Wayne Stambaugh
Maciej Suminski
John Beard