feaf626673
Add support for Atmel SAM3N devices.
2013-05-18 15:32:06 +12:00
cdaed128c1
stlink: add support for SRST handling
...
This enables SRST signals in open drain mode for both stlinkv1 and
stlinkv2 hardware platforms.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2013-05-14 12:34:53 +12:00
e0fc21a2a7
adiv5_swdp: allow to connect to a sleeping target by pulling SRST
...
This patch introduces a new command, "connect_srst [enable|disable]"
which allows to enable special mode in which SRST would be pulled low
before the SWD scan till attaching to a target.
Since on Cortex-Mx the SRST signal doesn't gate JTAG and SWD, it's
possible to connect to a target while holding reset, ask it to stop at
reset vector and only then deassert reset, thus allowing to attach to
the kind of firmware that goes immediately to sleep or disables
debugging by other means early on start.
Tested on an STM32VLDiscovery board with STM32F100 configured to go to
STOP mode and executing WFI in the very beginning of main().
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2013-05-14 12:32:44 +12:00
510d1c0dc8
Add support for burning flash on lpc4337.
2013-05-14 12:25:13 +12:00
4065169caf
Merge pull request #21 from fnoble/master
...
Python scripts shebang
2013-05-02 11:36:39 -07:00
7c3c9fdea3
Update python scripts to find user's preferred python binary through env.
2013-05-02 11:32:24 -07:00
56f44c39d9
nxp: support the lpc1114dip28 by Rickta59
2013-04-27 20:57:20 -07:00
e3f3171a33
usbuart: Fix build error and clean up whitespace.
2013-04-27 13:14:22 -07:00
43f7e7a3cf
Changes to the USBUART to make it less likely to drop characters at higher baud rates.
...
USB UART seems to work fine at 115.2Kbps or 230.4Kbps, but starts to drop characters
as the data rate goes higher. This commit changes the usbuart ISR to fill a software
FIFO, and adds a low priority timer interrupt to run deferred processing to drain a
FIFO and send USB CDCACM packets, rather than calling the usb send within the UART
ISR.
Tested on native platform, up to 1.5MBps.
2013-04-27 12:56:58 -07:00
f1ea5ed8f9
F4Discovery: Slow Down GPIO access a little, as off-board SWD otherwise needs _very_ good ground connection.
2013-04-23 13:43:43 -07:00
ad151fdca8
F4 Discovery: - Unconditionally use the System Bootloader - Use PC2/4/5/6 Pins for JTAG/SWD to avoid collision with eventual STLink Uart connection - Indicate Bootloader with blue LED
2013-04-23 12:14:18 -07:00
6659d87e9b
Remove DFU bootloader self protection.
...
It can still be enabled by building with -DDFU_SELF_PROTECT
2013-04-16 16:54:52 -07:00
126df7bb35
Allow extra LDFLAGS on command line. Use nano.specs for swlink.
2013-04-16 16:47:38 -07:00
45e02360b7
native: Fix up deprecated warnings.
2013-04-16 12:47:29 -07:00
89b908337d
Add missing #includes
2013-04-16 12:36:19 -07:00
67a96410e3
libftdi: Clean up warnings.
2013-04-16 12:33:28 -07:00
da448ec1a6
libftdi: Add 'flossjtag' cable.
2013-04-16 12:14:37 -07:00
6b7babf624
stm32f4: Add option erase command
...
--
Uwe Bonnes bon@elektron.ikp.physik.tu-darmstadt.de
Institut fuer Kernphysik Schlossgartenstrasse 9 64289 Darmstadt
--------- Tel. 06151 162516 -------- Fax. 06151 164321 ----------
>From d488dffe4dab4e5188c750489006260745a9e25a Mon Sep 17 00:00:00 2001
From: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
Date: Mon, 15 Apr 2013 15:26:58 +0200
Subject: stm32f4: Add option erase command
2013-04-15 10:22:17 -07:00
9c95f039cf
Make code compatible with newlib-nano and use it for stlink
...
With gcc-arm-none-eabi-4_7-2013q1-20130313 and -O2 I get
text data bss dec hex filename
45744 304 2376 48424 bd28 blackmagic
With -Os the results are even more impressive:
text data bss dec hex filename
37900 304 2376 40580 9e84 blackmagic
Since -Os might lower the debugging speed, do not enable it yet in the
absence of real measurements.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2013-04-14 11:48:59 -07:00
91b481731d
stm32f1/stm32f4: fix hardware CRC calculation
...
This was real-life tested on stm32f1 hardware including computation
for odd-sized ranges.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
2013-04-14 11:35:23 -07:00
7db6e3e00c
Revert "Revert "STM32: Use hardware CRC unit""
...
This reverts commit 58abbf7fc7
2013-04-14 11:28:46 -07:00
58abbf7fc7
Revert "STM32: Use hardware CRC unit"
...
This reverts commit 32b909067b
2013-04-04 21:37:51 -07:00
61d464bf09
dfu: Fix warnings.
2013-04-04 20:16:13 -07:00
d4411fc51f
Removed verison info from USB strings on native platform.
2013-03-31 12:18:11 -07:00
3a70b81cce
Add erase_mass command for stm32f4 devices.
2013-03-27 14:10:07 -07:00
d7a6f0165e
Accept new chip ID for stm32f4 and include flash layout for 2MiB parts.
...
Thanks to Mike Smith.
2013-03-27 11:24:43 -07:00
46898a71ce
Modified BMP Mini with extra connectors
2013-03-17 15:03:20 -07:00
2465846c0d
Updated project README.
2013-03-17 10:33:19 +13:00
44a03f31e1
Moved entropia design to contrib directory and added description.
2013-03-17 10:27:53 +13:00
6fb73e0a86
Add a version of BMP-mini optimized for manual production
...
This commit adds a variant of the Blackmagic Mini that uses only 0603
parts and standard connectors for better availability and easier manual
soldering.
Additionally, another voltage regulator has been used that is
cheaper, pin-compatible and has better characteristics.
2013-03-17 10:24:02 +13:00
87dad080e1
Fix build for f4discovery host.
2013-03-17 10:17:05 +13:00
931cd97f15
Removed stm32_can and usps_f407 platforms.
2013-03-15 20:50:55 +13:00
486c5de013
swlink: Add missing item to connector layout
2013-03-14 22:56:31 +01:00
920ced062e
SWLINK: Add variant for the STM8S Discovery board
2013-03-12 12:24:10 +01:00
e880c553fb
Restore trace timer interrupt handler.
2013-03-12 19:14:11 +13:00
7c2e994381
Split out platform specific bootloader parts to separate files.
2013-03-12 19:04:10 +13:00
55f161208d
Further split-up of DFU bootloader.
2013-03-12 15:00:15 +13:00
14e5e8b0b6
Separated clean and dirty bootloader sections.
2013-03-12 09:57:28 +13:00
7b10270007
Merge pull request #16 from zyp/master
...
Fix for broken USB flow control.
2013-03-08 15:18:12 -08:00
e8f9d52d2f
gdb_if: Fix USB flow control.
...
The introduction of the double buffering broke USB flow control, causing
loss of data when a new packet arrived with the previous still present in
the double buffer.
With this patch the endpoint is kept in NAK until the double buffer is empty.
2013-03-06 20:36:49 +01:00
530ee15153
Correct upload script for detection of F1/F4 start address.
2013-02-20 10:55:52 +13:00
d5be7b7a50
Merge pull request #11 from aibara/master
...
Another small fix for adiv5, ap_mem_write_bytes double increment analogous to previous fix for ap_mem_read_bytes
2013-02-18 00:51:45 -08:00
99ac73907f
Merge pull request #9 from jeffstaley/master
...
Bug fixes for lpc11xx code
2013-02-18 00:50:50 -08:00
acda4bd46c
Merge pull request #12 from UweBonnes/master
...
Make adaption to different STM32 boards easier
2013-02-18 00:49:35 -08:00
ff8de39774
usbuart: Don't try to send until configured. Enumeration may hang else
2013-02-15 17:55:36 +01:00
dee82a0d4f
Document changes between ST-Link V1 and V2 and implement needed changes
2013-02-15 17:39:27 +01:00
f8ea954275
STLINK: Add pointer to Discoveryboard modification instructions
2013-02-11 19:36:22 +01:00
71871b6bfd
Merge remote-tracking branch 'upstream/master'
...
Conflicts:
src/platforms/stlink/cdcacm.c
src/platforms/stlink/platform.c
src/platforms/stlink/platform.h
2013-02-07 12:09:51 +01:00
327ee49a67
usps_f407: add another platform
2013-02-03 14:22:14 +01:00
31f39339fd
stm32/usbdfu.c: Rearrange code to clarify the tasks to be done
2013-02-03 14:14:48 +01:00
Gareth McMullin
Paul Fertser
Allen Ibara
Fergus Noble
Gareth McMullin
Allen Ibara
Uwe Bonnes
Eric Brombaugh
Florian Larysch
Vegard Storheil Eriksen