src/hardware/saleae-logic-pro/protocol.c:389:12: warning: 'set_led' defined but not used [-Wunused-function]
static int set_led(const struct sr_dev_inst *sdi, uint8_t r, uint8_t g, uint8_t b)
^
CC src/hardware/saleae-logic-pro/api.lo
src/hardware/saleae-logic-pro/api.c: In function 'dev_acquisition_handle':
src/hardware/saleae-logic-pro/api.c:332:9: warning: missing initializer for field 'tv_sec' of 'struct timeval' [-Wmissing-field-initializers]
struct timeval tv = {};
^
In file included from /usr/include/x86_64-linux-gnu/sys/time.h:27:0,
from include/libsigrok/libsigrok.h:24,
from src/hardware/saleae-logic-pro/protocol.h:25,
from src/hardware/saleae-logic-pro/api.c:23:
/usr/include/x86_64-linux-gnu/bits/time.h:32:14: note: 'tv_sec' declared here
__time_t tv_sec; /* Seconds. */
^
The asix-sigma driver was reported to fail in combination with newer
libftdi versions, because the firmware upload routine opened again an
already opened device, and then failed to claim the interface. Which was
not fatal before with previous libftdi versions.
Remove the redundant open call. Remove the local FTDI context variable,
which brings the firmware upload routine in line with all other calls
that communicate to the USB device.
This fixes bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
The asix-sigma driver supports different samplerates, which will involve
different firmware images and will affect the number of available logic
channels as well as their memory layout in downloaded sample data.
Make sure to only store the configuration's parameters after the setup
of that configuration has successfully completed, and make sure to store
a consistent set of parameters. Specifically don't change the number of
channels when the firmware upload failed.
This fixes part of bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
The firmware upload code paths in the asix-sigma driver used to return
either the SR_OK code, or the magic number 0 for error conditions. Which
happens to be identical and cannot be told apart by callers.
Provide proper SR_ERR return codes for error conditions, such that
callers can tell whether the firmware upload succeeded.
This fixes part of bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
../src/hardware/hung-chang-dso-2100/api.c: In function ‘config_commit’:
../src/hardware/hung-chang-dso-2100/api.c:562:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
state = 0x01;
~~~~~~^~~~~~
../src/hardware/hung-chang-dso-2100/api.c:563:2: note: here
default:
^~~~~~~
../src/hardware/hung-chang-dso-2100/api.c:565:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret != SR_OK)
^
../src/hardware/hung-chang-dso-2100/api.c:567:2: note: here
case 0x01:
^~~~
The previous implementation used to provide datafeed packets which
contain logic data in positions that correspond to disabled channels.
Do mask out logic data of disabled channels in the memory image before
it is sent to the session's datafeed. This implementation works fine for
those situations where either all logic channels are enabled (default
configuration) or when only the upper channels get disabled (which can
be considered a typical use case).
For those configurations where enabled channels follow disabled channels
(i.e. setups with gaps in the sequence of enabled channels) behaviour
will be unexpected: Neither is the mask adjusted to contain gaps, nor
will enabled channels get mapped to result in a dense representation.
The respective code paths are marked with TODO comments.
Add a comment to discuss a non-obvious generator call for analog data in
the acquisition start routine, while we are here.
The generator logic determines how many samples per group (analog and
logic) need to get produced, then keeps iterating until each group has
reached the specified count. Different groups can generate different
numbers of samples per iteration, they have their own stride.
It's essential to check whether all channels in a group are disabled, to
then completely skip the respective half of the generation loop. Without
this check, the group would be expected to generate data but it won't,
which results in an endless loop. This was observed with analog channels.
There was another issue with logic channels. Unexpected logic data was
seen in the output although neither logic channel was selected.
This commit fixes bug #923.
Skip the emission of session datafeed packets for disabled analog
channels.
Implementation detail: Allow for quick lookup of the channel that is
associated with an analog generator, as the data generation routines
only pass generator references in later calls.
This fixes part of bug #923 (which initially is about unexpected
logic data while analog channels were affected in similar ways).
After the requested number of samples was sent, another session df
packet was emitted with one sample for the analog channels, which
contained the most recent result of averaging. Make this emission
depend on the "averaging requested?" flag.
This fixes bug #930.
The 'demo' driver supports scan options to adjust the number of
supported channels, and runtime control for the enabled state of
channels.
Starting with zero analog channels created (scan option) resulted in a
runtime assertion. Creating but disabling analog channels (GUI checkbox,
CLI option) resulted in unexpected output for disabled channels.
Move the creation of a hash table out of the conditional loop that
iterates over created analog channels. Which results in the table's
always being valid, and iteration during data acquisition yields no
analog output as is expected.
This fixes bug #625.
A previous implementation of the demo driver supported the creation of
larger channel counts yet only enabling part of them by default. This
was kind of pointless, I just was not aware of the available scan
options.
Drop the "enabled channels" limitation, enable all channels that get
created (like the implementation before the experiment did), and create
as many channels as was compiled in by default or later got specified
by scan options.
Before firmware upload some models (e.g. the original DSLogic or the
DSLogic Pro) don't have any USB manufacturer or product strings set, so
they wouldn't be detected.
Previously the USB communication code was split between api.ci,
dslogic.c and protocol.c, with protocol internals split between
both. This patch puts all the protocol handling code into one
source file reducing the number of internal interfaces and making
the code more readable.
Previously the USB communication code was split between api.c
and protocol.c, with protocol internals split between both. This
patch puts all the protocol handling code into one source file
reducing the number of internal interfaces and making the code
more readable.
Handle the case when the sample data memory was filled and has wrapped
around during acquisition. Download the respective part of the data
which is reliably available, only skipping a single 1KB row which might
contain either old or new data while it's not certain which it would be.
This will be essential when triggers later become available. Right now
it copes with user requests for sample counts that exceed the total DRAM
capacity. Instead the maximum available amount of data is provided.
Of course acquisition no longer gets stopped when the end of DRAM is
reached.
Correctly determine the size of a download chunk for the last DRAM row
that's involved in the recent data acquisition.
This commit is based on work done by jry@.
This addresses bug #838 (trailing garbage).
It's assumed that the previously downloaded excess data was "swallowed"
by the sample count enforcement logic that was applied earlier, so the
(remainder of the) issue could have gone unnoticed, unless some other
termination condition than sample count was used.
Configure the samplerate clock and channel count during acquisition
start in identical ways for 50MHz, 100MHz, and 200MHz modes.
This part was inspired by work done by jry@ yet was addressed in
different ways (no exception, do everything in every mode the same way).
Eliminate a portability issue in the previous implementation. Make sure
to send the configuration bytes in the correct order to the hardware.
Don't typecase a struct reference to a bytepointer and hope that the
internal memory representation might fit the external hardware's idea.
Add a comment about sample memory organization in a central spot. This
concentrates knowledge which otherwise would be spread across several
locations all over the driver's codebase, yet is essential to have at
hand during maintenance.
All of the information was determined/updated by jry@ with the help of
Ondrej at Asix when he did lots of fixes and improvements to asix-sigma.
The Asix Sigma hardware does not support a sample count limit. Instead
this optional input parameter gets mapped to a sample time, and some
slack for hardware pipelines and compression gets added. When data
acquisition completes and sample data gets downloaded, chances are that
there is more data than requested by the user.
Do enforce the optional sample count limit. Stop sending data to the
sigrok session when the configured number of samples was sent.
This commit is based on work done by jry@.
This fixes bug #838.
Enhance how the data acquisition is stopped. Wait for the hardware to
flag the successful completion of data retrieval as well as flushing
through hardware pipelines.
Use symbolic identifiers for the mode register's fields (for read as
well as write access).
This commit uses part of a code update to better match the documentation
done by jry@, but not all of it to reduce the size of the commit.
Minor adjustment for improved readability. Don't hide assignments in
variable declarations. Move initialization of some variables closer to
related evaluation or subsequent processing. Break a complicated looking
roundup expression into several short steps.
Fix how the READ_ID register index was passed to the hardware access.
Addresses are sent in nibbles, so shift by eight is wrong here. No harm
was done, as the register's index is zero.
The Asix Sigma driver is aware of three firmware images, which are
required for acquisition with up to 50MHz, 100MHz, and 200MHz. The
previous implementation always downloaded the corresponding firmware
image whenever the sample rate has changed, which was redundant.
Skip the download when the new samplerate uses the same firmware as the
previously selected samplerate did. This results in faster responses in
the GUI when the samplerate selection changes.
Move assignments out of the variable declaration block for improved
readability while we are here.
The hardware provides captured data at a maximum rate of 16bits per 20ns
(50 MHz). For samplerates of 100 and 200 MHz one individual 16bit entity
contains multiple samples for a reduced number of channels. The bits of
several sample points are interleaved within the 16bit entity.
This commit is based on work done by jry@ who fixed a lot of issues with
the help from Ondrej at Asix.
This fixes bug #840.
Adjust the interpretation of acquired sample data such that regardless
of 50/100/200MHz samplerate the assignment of LA pins to sigrok channels
remains stable.
Introduce helper routines to access the sample data that is provided by
the ASIX hardware, as well as the buffer which accumulates logic data
before it gets sent to the session's datafeed.
This hides endianess issues from call sites, and prepares access to
memory layout which varies with sample frequencies.
This commit is based on work done by jry@.
This works around bug #359. Triggers currently are not operational for
Asix Sigma. Don't claim support in the driver so that UIs won't use the
feature. Yet allow research in this issue, by concentrating the switch
for the feature's support in a central location.
Add/update a comment and unobfuscate an error code path while we are here.
Both the .c and the .h file declared the same identifiers for USB
properties of ASIX hardware with identical values. Remove the .c
incarnation and keep the .h content, as the names are used in api.c
as well as protocol.c sources.
Introduce a separate routine which maps sample counts and sample period
to an elapsed sample time after which acquisition shall get stopped.
Add some more time to make sure the most recent captured data has passed
the hardware pipeline and is available for download.
This commit is based on work done by jry@.
When "tsdiff < EVENTS_PER_CLUSTER" we don't want "tsdiff - EVENTS_PER_CLUSTER"
(a negative number) to be treated as (int).
Submitted-By: jry <jrysig@gmail.com>
[ gsi: massaged for mainline submission ]
Bump the number of supported logic channels from 8 to 128. This is
mostly motivated to test the 64 channels limit which some of the
components/subprojects of the sigrok project might have (input/output
modules, user interfaces).
Only automatically enable the first 8 of the 128 total logic channels,
i.e. default to the previous behaviour. Prepare to only enable part of
the set of analog channels, but stick with their being active by default
as well.
Factor out the choice for the default logic pattern, too. This allows
for easier adjustment of the default configuration, when settings are
concentrated in a single spot.
Extend the demo driver, add another waveform choice for logic channels.
Create a "cable squid" logo representation which occupies a large number
of channels.
This pattern occupies 128x128 pixels. Unlike the 'sigrok' pattern it
gets repeated when more channels are involved, but is not shifted in the
repetition.
The handling of the digital channels for this series is somewhere
between that of the DS1000D series (PROTOCOL_V2) and the MSO1000Z
(PROTOCOL_V4).
The :LA command set is similar to that of V4, but the LA data has to be
requested with :WAV:SOUR:LA and arrives in interleaved form like V2.
None of these changes should affect other models. They only affect the
case of PROTOCOL_V3 with digital channels, which occurs only for the
MSO2000A series.
Fixes#933.
We'd already had this problem elsewhere and thus have this wrapper function
that does this where necessary. It just wasn't in use on these two call sites,
which was causing timing problems when used over tcp-raw or VXI transports.
With trigger enabled, and with PulseView, a second (or more) acquisition
starts immediately instead of blocking. It's mandatory to try several times
to have a correct behavior.
According to http://mygizmos.org/ols/Logic-Sniffer-FPGA-Spec.pdf section 2.3.1
p.8, the Openbench Logic Sniffer must be reset before each arm command.
This fixes bug #809.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Openbench Logic Sniffer reset is a little more complex than a simple send.
To avoid code duplication, this patch adds a new function dedicated to
this task.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
This changes the fx2lafw code to only enable the wide_sampling (16bit)
method, if at least one of the higher eight channels is enabled. This
has the benefit, that we can use higher samplerates on 16bit LA
devices if we use only the first eight channels.
The wide sampling is also enabled if we have one or more analog
channels.
Signed-off-by: Jan Losinski <losinski@wh2.tu-dresden.de>
Uwe Hermann
Richard
Jan Luebbe
Gerhard Sittig
Joel Holdsworth
Soeren Apel
Angus Gratton
Martin Ling
Johannes Römer
Gwenhael Goavec-Merou
Marc Schink
Bert Vermeulen
Jan Losinski