Further "flatten" the DRAM layout's declaration for sample data. Declare
timestamps and sample data as uint16_t, keep accessing them via endianess
aware conversion routines. Accessing a larger integer in smaller quantities
is perfectly fine, the inverse direction would be problematic.
Keep application data in its logical presentation in C language struct
fields. Explicitly convert to raw byte streams by means of endianess
aware conversion helpers. Don't assume a specific memory layout for
C language variables any longer. This improves portability, and
reliability of hardware access across compiler versions and build
configurations.
This change also unobfuscates the "disabled channels" arithmetics in
the sample rate dependent logic. Passes read-only pointers to write
routines. Improves buffer size checks. Reduces local buffer size for
DRAM reads. Rewords comments on "decrement then subtract 64" during
trigger/stop position gathering. Unobfuscates access to sample data
after download (timestamps, and values). Covers a few more occurances
of magic numbers for memory organization.
Prefer masks over shift counts for hardware register bit fields, to
improve consistency of the declaration block and code instructions.
Improve maintenability of the LA mode initiation after FPGA netlist
configuration (better match written data and read-back expectation,
eliminate magic literals that are hidden in nibbles).
Move the 'devc' parameter to the front in routine signatures for the
remaining locations which were not adjusted yet. Reduce indentation of
continuation lines, especially in long routine signatures. Try to not
break string literals in diagnostics messages, rephrase some of the
messages. Massage complex formulae for the same reason.
Whitespace changes a lot, word positions move on text lines. See a
corresponding whitespace ignoring and/or word diff for the essence of
the change.
The driver got extended in a previous commit to accept any hardware
supported samplerate in the setter API, although the list call does
suggest a discrete set of rates (a subset of the hardware capabilities).
Update a comment to catch up with the implementation.
Drop the 250kHz item, it's too close to 200kHz. Add a 2MHz item to
achieve a more consistent 1/2/5 sequence in each decade. Unfortunately
50MHz and an integer divider will never result in 20MHz, that's why
25MHz is an exception to this rule (has been before, just "stands out
more perceivably" in this adjusted sequence).
Running several firmware uploads in quick repetition sometimes failed.
It's essential to stop the active netlist from preventing the FPGA's
getting reconfigured (FTDI to FPGA pins are so few, and shared). Delays
in a single iteration of the initiation sequence improves reliability.
Retries of the sequence are belt and suspenders on top of that.
Before the change, failure to configure was roughly one in ten. After
the change, several thousand reconfigurations passed without failure.
Use symbolic identifiers to select firmware images, which eliminates
magic 0/1/2 position numbers in the list of files, improves readability
and also improves robustness. Move 'devc' to 'ctx' and before other
arguments in routine signatures while we are here.
FPGA configuration (netlist upload) of ASIX SIGMA devices is rather
special a phase, and deserves its own state in the device context's
"state" tracking. Not only is the logic analyzer not available during
this period, the FTDI cable is also put into bitbanging mode instead
of regular data communication in FIFO mode, and netlist configuration
takes a considerable amount of time (tenths of a second).
Use common support for SW limits, and untangle the formerly convoluted
logic for sample count or time limits. Accept user provided samplerate
values when the hardware supports them, also those which are not listed.
The previous implementation mapped sample count limits to timeout specs
which depend on the samplerate. The order of applications' calls into
the config set routines is unspecified, the use of one common storage
space led to an arbitrary resulting value for the msecs limit, and loss
of user specified values for read-back.
Separate the input which was specified by applications, from limits
which were derived from this input and determine the acquisition phase's
duration, from sample count limits which apply to sample data download
and session feed submission after the acquisition finished. This allows
to configure the values in any order, to read back previously configured
values, and to run arbitrary numbers of acquisition and download cycles
without losing input specs.
This commit also concentrates all the limits related computation in a
single location at the start of the acquisition. Moves the submission
buffer's count limit container to the device context where the other
limits are kept as well. Renames the samplerate variable, and drops an
aggressive check for supported rates (now uses hardware constraints as
the only condition). Removes an unused variable in the device context.
Introduce a 4MiB session feed submission buffer in the device context.
This reduces the number of API calls and improves performance of srzip
archive creation.
This change also eliminates complex logic which manipulates a previously
created buffer's length and data position, to split the queued data when
a trigger position was involed. The changed implementation results in a
data flow from sample memory to the session feed which feels more natural
during review, and better lends itself to future trigger support code.
Use common SW limits support for the optional sample count limit. Move
'sdi' and 'devc' parameters to the front to match conventions. Reduce
indentation in routine signatures while we are here.
This implementation is prepared to handle trigger positions, but for now
disables the specific logic which checks for trigger condition matches
to improve the trigger marker's resolution. This will get re-enabled in
a later commit.
Add more symbolic identifiers, and rename some of the existing names for
access to SIGMA sample memory. This eliminates magic numbers and reduces
redundancy and potential for errors during maintenance.
This commit also concentrates DRAM layout related declarations in the
header file in a single location, which previously were scattered, and
separated registers from their respective bit fields.
Extend comments on the difference of events versus sample data.
Move the FPGA commands (which can access registers, and sample memory)
declarations before the register layout declaration. Which then no
longer separates the registers declarations from their bit fields.
Update comments on the register set while we are here.
Eliminate a few magic numbers in FPGA commands, use symbolic identifiers
for automatic register address increments, and DRAM access bank selects.
Improve grouping of related declarations in the header file.
Slightly rephrase and comment on the FPGA configuration of the ASIX
SIGMA logic analyzer. Use symbolic pin names to eliminate magic numbers.
Concentrate FPGA related comments in a single spot, tell the Xilinx FPGA
from FTDI cable (uses bitbang mode for slave serial configuration).
This fixes typos in the PROG pulse and INIT check (tests D5 and comments
on D6). Also removes the most probably undesired 100s timeout in the
worst case (100M us, 10K iterations times 10ms delay). Obsoletes labels
for error paths. Drops a few empty lines to keep related instruction
blocks together. Includes other style nits.
Stick with the FTDI library for data acquisition, and most of all for
firmware upload (bitbang is needed during FPGA configuration). Removing
this dependency is more complex, and needs to get addressed later.
Re-use common USB support during scan before open, which also allows to
select devices if several of them are connected. Either of "conn=vid.pid"
or "conn=bus.addr" formats are supported and were tested.
This implementation detects and displays SIGMA and SIGMA2 devices. Though
their function is identical, users may want to see the respective device
name. Optionally detect OMEGA devices, too (compile time option, off by
default), though they currently are not supported beyond detection. They
just show up during scans for ASIX logic analyzers, and users may want to
have them listed, too, for awareness.
This implementation also improves robustness when devices get disconnected
between scan and use. The open and close routines now always create the
FTDI contexts after the code has moved out of the scan phase, where common
USB support code is used.
This resolves bug #841.
Eliminate an unnecessary magic number for the maximum filename length of
SIGMA netlists. Use a more compact source code phrase to "unclutter" the
list of filenames and their features/purpose. Move the filesize limit to
the list of files to simplify future maintenance.
The UT32x driver requires a user spec for the connection. The device
cannot get identified, that's why successful open/close for the port
will suffice. Lack of an input spec as well as failure in the early
scan phase will terminate the scan routine early.
When we reach the end of the scan which creates the device instance
and registers it with the list of found devices, the port already
is closed and the list of devices will never be empty. Remove the
redundant close call and the dead branch which frees the serial port.
src/hardware/siglent-sds/protocol.c: In function 'siglent_sds_get_digital':
src/hardware/siglent-sds/protocol.c:382:35: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (data_low_channels->len <= samples_index) {
^
src/hardware/siglent-sds/protocol.c:391:36: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (data_high_channels->len <= samples_index) {
^
src/hardware/siglent-sds/protocol.c:417:32: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
for (long index = 0; index < tmp_samplebuf->len; index++) {
^
In file included from src/hardware/siglent-sds/protocol.c:37:0:
src/hardware/siglent-sds/protocol.c: In function 'siglent_sds_receive':
src/hardware/siglent-sds/protocol.h:28:20: warning: format '%li' expects argument of type 'long int', but argument 3 has type 'uint64_t {aka long long unsigned int}' [-Wformat=]
#define LOG_PREFIX "siglent-sds"
^
./src/libsigrok-internal.h:815:41: note: in expansion of macro 'LOG_PREFIX'
#define sr_dbg(...) sr_log(SR_LOG_DBG, LOG_PREFIX ": " __VA_ARGS__)
^
src/hardware/siglent-sds/protocol.c:564:6: note: in expansion of macro 'sr_dbg'
sr_dbg("Requesting: %li bytes.", devc->num_samples - devc->num_block_bytes);
^
src/hardware/siglent-sds/protocol.c: In function 'siglent_sds_get_dev_cfg_horizontal':
src/hardware/siglent-sds/protocol.h:28:20: warning: format '%lu' expects argument of type 'long unsigned int', but argument 3 has type 'uint64_t {aka long long unsigned int}' [-Wformat=]
#define LOG_PREFIX "siglent-sds"
^
./src/libsigrok-internal.h:815:41: note: in expansion of macro 'LOG_PREFIX'
#define sr_dbg(...) sr_log(SR_LOG_DBG, LOG_PREFIX ": " __VA_ARGS__)
^
src/hardware/siglent-sds/protocol.c:933:2: note: in expansion of macro 'sr_dbg'
sr_dbg("Current memory depth: %lu.", devc->memory_depth_analog);
^
Changing triggers (e.g. from low to high) would sometimes cause the
acquisition to seemingly "hang" due to missing variable initializations
(in reality the device would wait for incorrect triggers and/or on
incorrect channels).
This fixes bug #1535.
Prefer the common conversion helper for little endian 16bit signed data.
The previous local implementation only worked for positive values, and
yielded incorrect results for negative temperatures.
This fixes bug #1463.
Since we've now seen lots of devices in the wild that come with the
"HCS-" prefix in the ID, it's probably safe to assume all of them
could have it.
This fixes bug #1530.
The previous implementation got stuck in an infinite loop when data
acquisition started, but the device got disconnected before the data
acquisition terminates. An implementation detail ignored communication
errors, and never saw the expected condition that was required to
continue in the sample download sequence. Unbreak that code path.
Even though the devices/websites/manuals usually say 0..30V, the
hardware actually accepts up to 31V, both via serial as well as by
simply rotating the knob on the device (and our driver already
reflects that).
The same is true for current, it's usually 0..5A as per docs, but many
(probably all) devices accept 5.1A via serial and knob.
Thus, set the max current of all devices to 5.1A (or 3.1A for 3A
devices). We're assuming they all have this property, and we've seen
this in practice on at least three different versions of the device.
On a recently acquired Korad KA3005P power supply, the ID supplied by the
device is not known by libsigrok.
$ sigrok-cli --driver=korad-kaxxxxp:conn=/dev/ttyACM0 --scan
sr: korad-kaxxxxp: Unknown model ID 'KORAD KA3005P V4.2' detected, aborting.
This fixes bug #1522.
Thanks to bitaround@gmail.com for the amperage fix.
The DMMs report as an event to which mode the user switched (by turning the
rotary switch): "*0", "*1", etc.
Most other DMMs have few modes, but the U127x DMMs have up to 11 different
modes (i.e., "*10" is a valid event).
Gerhard Sittig
Frank Stettner
Tobias Faeth
Sergey Rzhevsky
Richard
Uwe Hermann
Florian Schmidt
Jan Metzger
Christian Fruth
Peter van der Perk
Tom Matthews
v1ne
Elen Eisendle
Andreas Sandberg
Daniel Trnka
David Sastre Medina
jirjirjir