When removing a point from the polygon, the vertex is removed before it
is tested for validity. If it fails validation, the edit is reverted
and the point count doesn't change, so the view update only modifies the
existing points. But the revert may also have changed the shared
pointer to the point array, invalidating the view's copy.
Fixes: lp:1821909
* https://bugs.launchpad.net/kicad/+bug/1821909
This inserts a translation map in the layer names so that the old stable
files with Italian/French layer names get updated to the standard
English layer names (instead of not opening).
Fixes: lp:1370575
* https://bugs.launchpad.net/kicad/+bug/1370575
Save/restore default netclass.
Read layers back in with correct syntax ('.' between keyword and layer name).
Write layers to project file.
Read/write layer enablement bits.
Don't set solder paste margin min to 0 (most of them are negative).
Fixes: lp:1811990
* https://bugs.launchpad.net/kicad/+bug/1811990
the filled areas can use a hatch pattern (crossing lines) using square holes.
The zone filler removes too small holes (truncated holes) from hatch pattern.
It avoid to create small holes when a hole pattern is truncated by the filled area base shape.
Tab through the grid vertically, then horizontally, as the fields
are laid out with "related" fields (like the co-ords) vertically.
Also neaten headers.
Fixes: lp:1821887
* https://bugs.launchpad.net/kicad/+bug/1821887
Commit 6006703798 fixed a crash but broke the filled zones changes detection.
Filled zones were always seen as not up to date due to the fact the filled areas were cleared too early.
The up to date detection is also optimized: the old filled polygons are no longer stored.
Instead of, the MD5_HASH is calculated and stored before clearing the filled polygons.
Autosave was not working correctly, partly due to different
implementations in eeschema and pcbnew and partly due to a mistaken
refactor at some point during v5 development. This unifies the expected
autosave prefix to _autosave- for both pcbnew and eeschema. It also
unifies the expected suffix for the backup files to -bak.
Fixes: lp:1820433
* https://bugs.launchpad.net/kicad/+bug/1820433
A zone refill display progress bar is shown when deselecting the zone after geometry changes.
However, on Linux, there are some artifact between the progress bar refresh and the board view refresh:
the filled areas are incorrectly shown: the insulated islands remain displayed,
although they are removed from the actual filled areas list
So it is disabled until a fix is found.
When dragging, you will seldom want to snap to the original item. This
commit prevents the "size of track" snap to the original item and
replaces it with an auxilary grid origin for the snap. This means
effectively that the snap will happen to grid for the original item
unless the cursor is closer to the original item line than it is to the
grid crossing.
Fixes: lp:1820248
* https://bugs.launchpad.net/kicad/+bug/1820248
Previously, in many cases the selected zone was refilled on exit selection, even if the zone was not modified.
This is annoying, because the zone fill can be really time consuming, and cannot be called without a good reason.
Now the refilling is made only if a zone parameter is actually modified.
The bounding box calculation needs to be fast and is threaded in many
places in pcbnew. We cannot invalidate items (the function is const but
this wasn't caught at compile-time for some reason) when getting the
bbox. This shouldn't be an issue as the m_BezierPoints is rebuilt each
time the curve is updated, so rebuilding during the bbox seems extra.
Fixes: lp:1819984
* https://bugs.launchpad.net/kicad/+bug/1819984
Removing existing fills will prevent re-drawing invalid polygons before
they are ready. This seems to happen on Macs more easily due to redraw
timing.
Fixes: lp:1819553
* https://bugs.launchpad.net/kicad/+bug/1819553
Allows 0 to 4 chamfered corners, not only one.
A custom shape allow this kind of shape. However because it is a primitive,
it is easier to edit and it support thermal reliefs.
This was due to the stub removal tests if a stub end is outside a solid area to remove it.
There is a corner case: is the stub end is exactly on a solid area outline extra segment
created by Fracture() used in calculations.
The stub removal tests are now made before fracturing.
Fixes: lp:1819317
https://bugs.launchpad.net/kicad/+bug/1819317
The module refdes always increment by one. This is problematic
for two reasons:
* It doesn't work when more than one FP is selected (say you have
C1 and C2, you get C1, C2, C2, C3)
* It messes with simple panellisations
The 5.0.x behaviour is to not renumber in Pcbnew, so revert to
that behaviour.
Better refdes incrementation can come post 5.1, as this will need
new strings and UI.
Fixes: lp:1819106
* https://bugs.launchpad.net/kicad/+bug/1819106
Disable the text update event for the orientation cutom value field before
updating it when the radio buttons are selected. This allows to use the
conventional EVT_TEXT handler, rather than KEYDOWN, which has two effects:
* Tabbing though the dialog no longer sets custom orientation
* Click-driven clipboard actions trigger the update correctly.
Introduce a helper function in validators.h to assist in updating
validated fields without triggering further events.
Fixes: lp:1819006
* https://bugs.launchpad.net/kicad/+bug/1819006
When checking for closed outlines, we generate a board area using the
pcb structure. We now also check for overlapping outlines due to
lp:1818163 However, the DRC maintained its previous outline before
generating the new one, causing an overlap error.
This regenerates the board outline from zero for each DRC run.
Fixes: lp:1819012
* https://bugs.launchpad.net/kicad/+bug/1819012
pcbnew refreshes the viewItem for the worksheet multiple times. This
requires setting the filename to get parameters displayed on the
worksheet correctly.
Fixes: lp:1819000
* https://bugs.launchpad.net/kicad/+bug/1819000
Depending on thermal reliefs size, the polygons could be self intersecting,
and these self intersecting polygons are unexpected in zone calculations.
Other fix: the width of thermal stubs is clamped to the size of pads.
Previously, a bug in clamping calculations prevents constraining thermal stubs width.
Fixes: lp:1818752
https://bugs.launchpad.net/kicad/+bug/1818752
Set the focus to some control in the copper zone, non-copper zone, and
keep out zone dialogs required for the default button action to work
properly. This only seem to affect windows dialogs.
Fixes lp:1818397
https://bugs.launchpad.net/kicad/+bug/1818397
wxWidgets has several bugs that result in cell editors being closed
right after they're opened. There are two wxWidgets hacks to
partially address this: the SetInSetFocus() hack, and a slow-click
hack. We used to try and work-around these bugs ourselves for
single-click access, but this changelist moves those over to
wxWidget's slow-click hack.
Fixes: lp:1817965
* https://bugs.launchpad.net/kicad/+bug/1817965
Added checks to StrCmpNum() function in common/sting.cpp to prevent
iterating past the end of the sting. Also removed length of string
parameter since it did not seem to be used anywhere.
Fixes lp:1818157
https://bugs.launchpad.net/kicad/+bug/1818157
* fp editor: ensure axis are drawn after switching the backend
* DIALOG_PNS_SETTINGS: ensure violate DRC option is correctly enabled/disable when opening the dialog.
Violating the DRC cannot happen in shove or walk around mode as we use
the DRC to calculate these actions. The tooltip explains this as well
but we need to explicitly disable the checkbox to prevent users from
thinking that they can complete DRC violating tracks in other modes.
Introduce a shortcut method to set tab ordering and use it in
the dialogs that override the tab traversal orders:
* Eeschema sheet properties
* Pcbnew Move exact
* Pcbnew Move relative
Also set some initial focus fields in the same dialogs.
Tidy a few includes.
Fixes: lp:1816009
* https://bugs.launchpad.net/kicad/+bug/1816009
Includes Edit Text and Graphics Properties and Edit Track and Via
Properties. It's also no longer board-specific as it turns out the
board timestamp is always 0 anyway.
When moving user user units out of the global, we missed that Python
calls were using it. This re-adds a function to retrieve user units
allowing the python scripts to show users dialogs in their preferred
units.
The default hot key definition for toggle high contrast mode was 'H'.
On windows, the menu accelerator handler code was grabbing the character
so it would not appear in the filter text control. This is expected
because the windows wxWidgets code hooks this at the application level
so that once a menu accelerator key is found, all further event handling
for that key stops. Changing the hot key definition to 'Ctrl+H' resolves
the issue.
Fixes lp:1803556
https://bugs.launchpad.net/kicad/+bug/1803556
The best size was calculated from a default size.
This default size (calculated by wxWidgets) was fully broken with some texts in a few languages.
So now this best size does not use this default size.
Fixes: lp:1816315
https://bugs.launchpad.net/kicad/+bug/1816315
gal: pixel alignment for Cairo.
gal: pixel alignment for OpenGL
Cleanup of pixel alignment patches
gal/opengl: more pixel alignment patches:
- works on Retina displays now
- pixel alignment for circles
- correct 1-pixel strokes
- fixed unfinished 1-pixel line ends
GAL: Restore antialiasing options in Cairo
GAL: Fix arc drawing
Removes DrawArcSegment, which drew arcs whose edge was optionally
stroked (a feature that we did not use). Fixes Cairo arc drawing issue
where arcs were not visible in pcbnew.
gal: further cleanup
gal: removed unused shader parameter
Auto-selecting of the first grid element is performed in the footprint
editor to facility rapid editing. Rapid editing of the 3d-model fields
is not as useful and requires multiple esc-keys to cancel. This limits
the auto-edit to only the reference tab.
Fixes: lp:1815456
* https://bugs.launchpad.net/kicad/+bug/1815456
Highlight connections is meant to show the copper connections on a
board. We remove the non-copper pads from our selection when attempting
to source the net for highlighting.
Fixes: lp:1815898
* https://bugs.launchpad.net/kicad/+bug/1815898
Items that are located at the edge of or outside of integer limits will
not be shown on screen as they don't fit in the VIEW RTree. This
prevents them from being edited and can corrupt data output. Instead,
we place them at the largest value that is representable on the RTree
(INT_MAX/SQRT(2)). This allows the user to correctly utilize DRC as
well as interact with and remove the offending items.
Fixes: lp:1815642
* https://bugs.launchpad.net/kicad/+bug/1815642
The parent window was always the board edit frame,
but this is incorrect when this dialog is called from the Plot dialog.
Fixes: lp:1815530
https://bugs.launchpad.net/kicad/+bug/1815530
When adding colors to length tuner, we depend on the window background
color, which can be set by the user, resulting in an unreadable text.
This uses the HSL conversion to detect which shade it should use for the
coloring.
Also adds test cases for round-trip HSL and HSV conversion
Fixes: lp:1814530
* https://bugs.launchpad.net/kicad/+bug/1814530
Update 3D model panel on initial dialog load to reflect the current
visibility state of the 3D model.
Fix a few minor footprint properties dialog spacing issues.
Fixes lp:1815184
https://bugs.launchpad.net/kicad/+bug/1815184
Fix wxGrid column minimal widths on Windows in dialogs (just fixing the size is not enough).
WX_GRID::GetVisibleWidth(): make width bigger for labels, because they usually use a bold font.
(However, the fix is just a workaround: a better code is welcome)
Using the normal command, oval holes are "drilled" by a route command.
Some board houses do not accept this normal command.
In this case, the drill dialog allows using an other Excellon drill command (a slotted hole).
Note also some board houses do not understand this alternate command!
GTK does not handle enlarged text layouts automatically, so we need to
get the screen size before choosing the correct grid width for the
dialog
Fixes: lp:1788495
* https://bugs.launchpad.net/kicad/+bug/1788495
When doing a global edit of the tracks and vias, we need to allow for
the possibility that the track size doesn't change and that this is
explicitly allowed without DRC error.
The using the "first available" numbering option, force an
artifical linear numbering scheme starting at '1'.
Start the pad name provider at the 0'th pad index.
Also adds a few related tests and adjusts tests affected by
this change to reflect that the offset still applies.
This can be expanded in future to be more general by skipping
pad (which would allow a custom start and numbering scheme
while still avoiding duplication), but for now,
this does what the UI says and avoids string changes in 5.1rc.
Fixes: lp:1814918
* https://bugs.launchpad.net/kicad/+bug/1814918
Fixes: lp:1814917
* https://bugs.launchpad.net/kicad/+bug/1814917
* Make LIB_TABLE_BASE::GetCount() return unsigned. This is more
consistent with the behaviour of STL containers (especially the
boost::ptr_vector this is really accessing). Sadly
wxGridTableBase() forces an int, so a cast is still required
at the WX interface.
* Make LIB_TABLE_BASE::At() return a reference. First, this is more
consistent with normal STL indexing operator[]'s, and secondly, it
allows an idiomatic const index method (so you can access const
LIB_TABLE_ROWs from a const LIB_TABLE_BASE).
The motivation is to allow use of this class and LIB_TABLE_ROW
in a test program, where the LIB_TABLE_BASE is const.
Libpolygon can provide its own includes via target_include_dirs PUBLIC.
This means any linking targets do not need to specifiy them manually.
As common requires polygon, the polygon dep is also now no longer
required downstream of libcommon, as it's transisitvely implied
by libcommon's target_link_libraries.
This resolves a circular dependency previously detected and also
simplifies CMakeLists.
The bitmap definitions (BITMAP_DEF and so on) do not
have any dependencies on other libs, including WX. This
means the bitmaps library can be isolated from the other
dependencies.
Common now depends on bitmaps, and libraries that depend
on common can pick it up from the common target_link_libraries,
as it is PUBLIC. This means a lot of targets no longer
need manual bitmap linkage.
This avoids a circular dependency that was previously reported
by static analysis.
Avoiding pulling in WX and other headers into the include
tree of each bitmap .cpp is a huge speed up (around 10x) in
compilation, and the generated static library is also 10x
smaller (20MB vs 200MB)
Add common as a link library to pnsrouter,connectivity.
THese library do still use common code (including bitmaps,
via base_screen.h) and this allows them to pick up the libcommon
includes correctly.
In countries using a comma as floating point separator, the --min-distance="0.0100 mm" was passed as --min-distance="0,0100 mm"
This is incorrect and broke the command line.
Fixes: lp:1814559
https://bugs.launchpad.net/kicad/+bug/1814559
Circles and Squares are handled correctly. Octagons are converted to
circles. Pad 1 is identified by the "1" string in the Eagle name.
Fixes: lp:1784126
* https://bugs.launchpad.net/kicad/+bug/1784126
Fixes and issue where forces were calculated using the current track
width even in differential placer mode where the tracks are specified by
the differential pair width.
Fixes: lp:1814480
* https://bugs.launchpad.net/kicad/+bug/1814480
When creating new lib table rows, the pointer becomes managed by the new
table through the boost::ptr_vector. The row is non-copyable, however,
so we lose the reference as soon as it goes out of scope. Creating a
clone provides a new pointer that is moved into the table on creation.
Fixes: lp:1792456
* https://bugs.launchpad.net/kicad/+bug/1792456
Choosing the drag origin should not be dependent on the snap settings in
pcbnew. Snap settings are sensible when you are designating a target
only. Additionally, when dragging a module, we do not want the
footprint's pads to be used as targets for snapping.
Fixes: lp:1814402
* https://bugs.launchpad.net/kicad/+bug/1814402
When the user cancels the footprint load, we should assume they are
canceling the placement of a new footprint. This also adds sanity check
when populating the list
Fixes: lp:1814181
* https://bugs.launchpad.net/kicad/+bug/1814181
It was a regression from 5.02 version.
The block of new footprints to place has now its reference point (the point that is on the graphic cursor) fixed.
This is the first footprint loaded from the list.
This breaks the following functions out to a general-purposed refdes utils
header:
* MODULE::GetReferencePrefix()
* kicad_string.h RefDesStringCompare()
This acheives:
* Slimming of MODULE interface
* Placement of refdes code in common rather than pcbnew
** Testing of this code in qa_common
* Tighter and smaller includes for code that only needed refdes functions
Note: there are failing tests commited (as expected failures). These
are the cause of lp:1813669 and will be fixed as a follow-up commit.
This is not logic specific to MODULE. Breaking it out to
kicad_string.h acheives:
* Slimming of the MODULE interface
* Enables reuse of the function
* Enables testing of the function
Also add a test under qa_common for this function.
The CONFIG_SAVE_RESTORE_WINDOW class does not need to be tied
to the array dialog, put it in common/widgets.
Also do a refactor and tidy-up of the the class, use a union for (slightly)
better type-safety and syntax (a variant would be better but that's C++17).
Also enable integral field save/restore from text boxes.
Fully initialise the CREATE_ARRAY_DIALOG_ENTRIES object,
and use these values for the dialog on first open. Currently,
the initial values aren't all initialised, and none are used, as the
valid flag is not set. This means there are poor defaults in some
fields.
Also more declarations and defintions of CREATE_ARRAY_DIALOG_ENTRIES
to the .cpp, as these do not need to be exposed in the header,
even privately.
The original item is part of the array, so give it a number
and put it in the right place (all current array tools have
a null transform for the first item, but it's not part of the
contract. For example, a circular array with an angle offset
might want to move the first point).
The numbering axis priority (h then v or v then h), and alternate
reversing are not actually numbering parameters, they are part of
the geometry of the array (the items are physically in different
orders).
So enable these options, even when numbering is disabled.
Also fix broken logic about when numbering scheme is enabled
(it still applies even if the numbering offset is fixed.)
The current module cannot be queried for existing pads as we
add them (because we never commit, until we finish the whole array).
Instead, pre-gather the names and check as we add, skipping any existing
names.
Note: this will not prevent arrays becoming "mis-ordered", but there
is not a lot we can do to prevent all possible errors.
Fixes: 1808706
* https://bugs.launchpad.net/kicad/+bug/1808706
The same principle could be used to skip existing ref-des'es on PCBs.
The geometry and numbering logic is separate to the dialog, and
can be separated for clearer logic and better testability.
Moreover, refactor it to avoid any dependency on pcbnew
classes, so it can be move to common for potential re-use in
eeschema and friends in future.
Also convert all wxPoint logic in these classes to VECTOR2I and
fix some function visibilities.
Add some unit tests of the ARRAY_OPTIONS geometry and numbering.
Snap/Grid modifier follow preferences from 05483a06c6. Brings Shift/Alt
modifiers into alignment with drawing tools. Shift modifier still
conflicts when choosing end item with the complete track click-modifier.
This will be addressed in v6 with a larger preference setting.
Snapping to item options were partially disconnected when unifying
framework. This re-attaches the options and adds the additional option
for graphical items.
Fixes: lp:1801377
* https://bugs.launchpad.net/kicad/+bug/1801377
kicad2step has a tolerance level that sets whether two points are at the
same location or not. This allows KiCad to access these levels to some
degree, permitting a looser interpretation of a closed board outline.
The selection for interactive drag uses cursor position off grid to
choose the element for dragging. We pass the same value into the start
dragging routine to choose the correct end of the element.
Fixes: lp:1813665
* https://bugs.launchpad.net/kicad/+bug/1813665
Rather than selecting an arbitrary track to snap, we select the closest
track to our point, allowing the via to be placed along the full track
length.
Fixes: lp:1813324
* https://bugs.launchpad.net/kicad/+bug/1813324
Some microwave inductor lengths cause invalid outputs
for the calculations, which causes jagged outputs.
* If the request length is such that four arcs and no straight
segments is too long
* If the length is such that an N-turn coil is too short, but
an N+1-turn coil is too long. This can happen when the coil
count is small.
This patch doesn't fix the underlying geometric issue here - fixing
the first requires a numerical method, and fixing the second probably
needs an iterative approach. Both of these could benefit from
a refactor.
However, this patch does prevent the tools producing invalid outputs,
which can sometimes be quite subtle mistakes if the "jags" are small.
Fixes: lp:1792119
* https://bugs.launchpad.net/kicad/+bug/1792119
Phoenix doesn't have the same initialization as wxpython3 and so the
namespace doesn't get the wxApp() initialized to the existing instance.
In python, this is worked around by starting a new wxApp.
Unfortunately, this appears to overwrite the existing global instance
variable. The issue _appears_ to be in Phoenix but for now we work
around it by saving and resetting the instance pointer in the main app.
The downside is that Python likely won't be able to respond to events
from C++
Fixes: lp:1809913
* https://bugs.launchpad.net/kicad/+bug/1809913
In the past, the ZONE_CONTAINER::GetPosition() member
returned a reference to a wxPoint, in accordance with the
BOARD_ITEM interface. This meant that ZONE_CONTAINER had
to reinterpret_cast a VECTOR2I (its internal position data) to wxPoint,
which was possible only due to fortunate memory layout.
This interface was changed to return wxPoints by value in
commit a4528988ca, and the normal (wxPoint) cast was used instead.
Thus, we can now also remove the dire warnings and static_asserts
used to ensure the now-unused old method was correct.
Introduce the concept of a DRC_PROVIDER which allows
to separate the various DRC functions to their own
areas. This allows, amongst other things, a slimmer core
DRC class, and allows DRC functions to be separately testable.
The courtyard DRCs (overlap, missing and malformed)
are the first victims, so instrumentation can be added to this function.
Add some unit tests on this DRC function, as well a few re-usable PCB-based
utility functions in a library (qa_pcbnew_utils) that could be shared between
unit tests and other utilities.
This separates the "newMarker" functions from the DRC class. These
are moved to a new class, DRC_MARKER_FACTORY, which is now responsible for
constructing suitable markers from BOARD_ITEMS.
The reasons for this are:
1) Allow DRC related functions to access theese functions without having
to bake these functions into the main DRC class.
2) Thereby simplify the DRC class interface
3) As DRC_MARKER is now a small class with public interfaces, it's
possible to put unit tests on these functions.
The motivation here is to allow to start to split out pieces of DRC
into separate classes.
Prior to placing the via, we check if the resulting via will pass too
close to different nets on different layers.
Fixes: lp:1718827
* https://bugs.launchpad.net/kicad/+bug/1718827
Previously, when the 3D viewer is opened, each board edition creates a 3D view refresh, that usually takes a bit of time.
Now the refresh is postponed until the 3D viewer has the focus.
When creating the zone cutout, we delete the old zone and add a new one
with each cutout. This requires resetting the source zone and clearing
our previous selection if we would like to continue using the cutout
tool on the new zone.
Fixes: lp:1812339
* https://bugs.launchpad.net/kicad/+bug/1812339
Plotting mask layers, we expand by a minimum width before performing a
boolean add of the separate regions. The boolean add has a separation
condition that includes equality. Since we are looking for the
complement of the mask, we would like the equality applied to the other
side. Removing a unit value provides the separation.
Fixes: lp:1698457
* https://bugs.launchpad.net/kicad/+bug/1698457
When loading an existing file, a missing value in the soldermask min
width value should not be interpreted as a default value but rather as a
0 value. This corrects an issue introduced by 4d709d2392
When prompting for a new footprint library, we need to treat the input
as a file for creation rather than a directory for selection.
Otherwise, users cannot specify the name of their new footprint library
independently of the existing directory names.
Fixes: lp:1812135
* https://bugs.launchpad.net/kicad/+bug/1812135
There is some odd interaction in the default copy constructor for
TOOL_EVENT using boost::optional under gcc. Avoid this by explicitly
constructing the event needed for cut
Fixes: lp:1812848
* https://bugs.launchpad.net/kicad/+bug/1812848
the stroke mode was always activated, even in fill mode. creating incorrect size shape for null length track segments.
Fixes: lp:1812532
https://bugs.launchpad.net/kicad/+bug/1812532
This issue created memory leak and not working wxComboboxes (for instance after modifying the language selection).
Now, these wxComboboxes are created only once, never recreated.
Also: minor cosmetic enhancement in footprint editor main toolbar
(the save footprint icon is modified if the footprint is saved to the board or to the library)
- Added ignore netcode option to CONNECTIVITY_DATA::GetConnectedItems()
- PlaceModule() now ensures the module added to the board (and thus to the connectivity database) has correct bounding box necessary for R-trees to work
- Use recursive connected pad search so that the new net is propagated to all pads
Fixes: lp:1787961
* https://bugs.launchpad.net/kicad/+bug/1787961
When renumbering pads, you can click on a pad the second time to restore
the pad to its original value. This did not allow a user to then place
the removed number on the correct pad (assuming a mistake). This commit
ensures that removed pad numbers are remembered and allow the user to
place in the correct pad.
When adding an element to a module, we don't need to update the relative
coordinates. Doing so can cause changes when writing to file depending
on rotation and position.
Fixes: lp:1810870
* https://bugs.launchpad.net/kicad/+bug/1810870
If the user does not build the GITHUB plugin (deprecated), we cannot use
it in our footprint load and should remove the define to ensure
accidental use is caught at compile time.
The config was saving a canvas type EDA_DRAW_FRAME member not always accurately initialized.
And the last canvas opened frame setup was saved, not necessary a frame having a canvas type that can be set by user.
This is a broken feature especially because the footprint viewer has a fixed canvas setting.
No net zones, by definition, do not connect to any other element.
Therefore, the entire net is an island and should not be removed by the
knockout section
Fixes: lp:1811239
* https://bugs.launchpad.net/kicad/+bug/1811239
Use the AddFileExtListToFilter() to also generate the
wildcard for "all files". This is because:
* Users can use AddFileExtListToFilter for the all files WC
with the same interface as for any other extensions.
* Users do not need to worry about wxGetTranslation, as the
_() is applied in the same way as the other *Wildcard() helpers,
and it is a function just like the others, so it is consistent
* There is a testable interface to document the expected result.
The test is added.
The local/dynamic ratsnest needs to calculate on a per-pad basis as the
module is always listed as having a visible ratsnest. This fixes the
finalized ratsnest viewed when routing as well as the show local
ratsnest regression.
Fixes: lp:1811010
* https://bugs.launchpad.net/kicad/+bug/1811010
Non-connected zones are, by definition, not connected, therefore, we
should not knock out thermal reliefs under any case
Fixes: lp:1810989
* https://bugs.launchpad.net/kicad/+bug/1810989
Frame refresh in wxWidgets sets the focus back to indeterminate state
and prevents hotkey action until the focus is captured again. Using
canvas update is the correct method to update the canvas display after
modifying zones/similar
Fixes: lp:1810993
* https://bugs.launchpad.net/kicad/+bug/1810993
When routing in high-contrast mode, the user may wish to place items
that are primarily on a different layer while remaining in high contrast
mode. This fixes a regression from 4.0.7
Fixes: lp:1804309
* https://bugs.launchpad.net/kicad/+bug/1804309
The standard DIM() macro was not typesafe as it happily deferred errors
to runtime that can be caught at compile time. Replacing it with a
generic C++11 constexpr allows for typecasting, comparison and compile
time error checking.
Devolve the logic as to whether a pad should be numbered or not
to a pad utility function. Add a very simplistic test for this
function (demonstrating how to test BOARD_ITEMs in general).
Fixes: lp:1804787
* https://bugs.launchpad.net/kicad/+bug/1804787
It is very difficult to select 0-width lines and they aren't physical on
the board. Items with this setting in Eagle should revert to the
default in KiCad.
Fixes: lp:1808584
* https://bugs.launchpad.net/kicad/+bug/1808584
Cairo supports antialiasing when rendering but can be slow when set to
sub-pixel mode. This bumps the minimum version of Cairo to 1.12
(available in 14.04 LTS as well as mingw) to support three antialias
settings (fast, good, best) that offer speed/appearance tradeoffs.
This can provide a higher-quality eeschema render as it works on a
per-element basis as opposed to the OpenGL per-screen antialias.
Currently, GAL is initialised to NONE (i.e. off). This causes
issues when Legacy canvas is broken (i.e. GTK3).
This changes the default to GAL Cairo, both in PCB_EDIT_FRAME
init, and in the config load.
Now, when the user starts with no config, they are prompted for
a choice: OpenGL or Cairo, and one of them will be set up, with
Cairo as fall back.
Users on platforms that still support legacy can go to it as normal
from the menu, but it will not be the default in any circumstance.
Fixes: lp:1809997
* https://bugs.launchpad.net/kicad/+bug/1809997
Where we can get away with lower segment counts (localizing an anchor),
we keep the low-def 16 segment count. Intermediate values and values
that are visible to the user are set to high definition. Most are
simply hints to the inflation correction but where they show, the user
show see smooth lines.
Most rounding operations have been shifted to an absolute error
calculation and the ability to adjust zone segment counts has been
removed in 5.1. The remaining elements that use fixed segment counts
are either 18 (DRC) or 32 (plotting). This aligns the punchout segment
count with the higher (32) definition value
wxChoice centers the selection on GTK. So when switching from a
mid-list item to an item at the top, the list is always cut off for
choice lists located on the top toolbar. Using a combobox provides a
drop-down that allows easier access to all elements in the box.
Fixes: lp:1808569
* https://bugs.launchpad.net/kicad/+bug/1808569
The hotkey name "Help (this window)" does not describe what the hotkey
and associated action does. It displays the current hotkey list, so the
action name should reflect that behavior
Moving pcbnew error strings that may be seen by the user to translated
strings. Strings that denote unexpected cases are moved to debug logs
as they are essentially asserts that should never be shown. The
exceptions are the messages shown when files are loaded. All unknown
items should show an error here.
Checks for ratsnest enabled prior to calculating and displaying the
local/dynamic ratsnest. Calls the ratsnest clear from selection clear
Notably, it appears that the tool actions do not chain transitions for
the same event. So only a single action (first specified) will be
executed when an event fires unless the actions are executed by separate
tools.
Fixes: lp:1809752
* https://bugs.launchpad.net/kicad/+bug/1809752
This make the use of legacy canvas on GTK3 a default-off
advanced config. Legacy is substantially broken on GTK3
and is of basically no use at all to general users on this
platform.
If the program starts with legacy canvas in the config,
it is forced into a GAL mode, as otherwise it could happen
that the user is stuck and unable to get into pcbnew to change
the setting.
Fixes: lp:1803156
* https://bugs.launchpad.net/kicad/+bug/1803156
While not technically allowed, overlapping polygons can be drawn in
pcbnew. Gerber polygons are strictly simple, however, so we need to
fracture prior to exporting to avoid invalid gerbers.
Rather than depend on proper unlocking for each exit, we move the
connectivity lock mutex into an RAII-type configuration that
automatically unlocks on exit.
Layer bit sets get chosen for the layer name, starting with the copper
layers and then the technicals. Additionally, multi-layer pads are
appended with an indicator that additional layer bits are set.
Fixes: lp:
* https://bugs.launchpad.net/kicad/+bug/
When importing footprints, some are generated with non-standard (e.g.
"mod") extensions. As a last option, we allow the * wildcard to select
these files for import.
Use TesselatePolygon() to draw polygons in Gerbview instead of GLU tesselation, much slower.
Add helper methods in GAL to know if the current GAL engine is Cairo, OpenGL or something else,
useful to optimize drawing code.
This fixes the handling of align/distribute tool when called on locked
items. Locked items cannot be moved but they may be used for the target
of an align/distribute operation.
Fixes: lp:1808238
* https://bugs.launchpad.net/kicad/+bug/1808238
Instead of a nag screen for locked items, we allow first the unlocked
items to be deleted and then, with a repeated request, the locked items.
This adds a popup cursor window informing the user of the option for
repeating the delete
Fixes: lp:1806507
* https://bugs.launchpad.net/kicad/+bug/1806507
Previous version had minimum width to account for it being difficult to
click on small lines. This should not be used for filled polygons
Fixes: lp:1808141
* https://bugs.launchpad.net/kicad/+bug/1808141
Simply calling it Alternative Delete was hiding its behavior. This gives
a descriptive tooltip and command name allowing users to more easily
find the equivalent to the "Ripup" command
This updates some of the footprint wizard values to use the default KLC
values for silkscreen, fab, courtyard and text.
Also updates the default QFN settings to create a valid footprint
Make sure the view is rebuilt before selecting the new footprints
so that they're shown only in the selection overlay.
Don't start the drag until the dialog is closed so we don't have
a bunch of extraneous mouse warping.
Fixes: lp:1775265
* https://bugs.launchpad.net/kicad/+bug/1775265
This allows people to continue to use the edge-width as a proxy
for board edge clearance until we implement board edge clearance
as a real feature.
Fixes: lp:1797787
* https://bugs.launchpad.net/kicad/+bug/1797787
Graphic lines and polygons are drawn to fit specific areas for which it
is helpful to have the endpoint controlled by the cursor even when
constraining the angle.
Fixes: lp:1805502
* https://bugs.launchpad.net/kicad/+bug/1805502
IsPolygonFilled() replaces the hard coded comparisob with Edge_Cut in code.
For now the polygon is not filled only on Edge_Cut layer.
But in the future, it could be an option for other layers.
Commit 1858b7dca corrected the handling of polygons on the edge cut
layer for board items. This adjusts for the possibility of polygons
in modules on the edge cut layer by applying the module offset/rotation
to the polygon elements.
Like circles, polygons are self-closed elements that define an outline.
This allows them to be used as such for board outlines and cutouts.
Fixes: lp:1795563
* https://bugs.launchpad.net/kicad/+bug/1795563
This allows too turn it on for work without an additional patch.
Also fix a bug in the disable code - when the SVG is enabled,
allow to select SVG files.
When loading the load using the UI, netclasses and net info are
synchronized to the board object after parsing the file. This needs to
happen automatically when loading the board via the Python interface as
well.
Fixes: lp:1806506
* https://bugs.launchpad.net/kicad/+bug/1806506
In DRAWSEGMENT polygonal shape: the commit tried to use triangulation (CacheTriangulation) to draw the shape (similar to zones).
It was much faster than using GLU tesselator (one order of magnitude).
Unfortunately, CacheTriangulation() works only with simple polygons, not with any polygon.
And simplifying a polygon with a lot of vertexes is very time consuming.
So using CacheTriangulation() is now removed and GLU tesselator is used as previously.
Fixes: lp:1806411
https://bugs.launchpad.net/kicad/+bug/1806411
SVG import need some refinements to be efficient, so it is disable for v 5.x.
Will be re-enabled later.
Enabling SVG import is *only* for developers, not for users.
* Do not compile dxf old files.
* import gfx, gal mode: make absolute placement working.
* Import gfx in legacy canvas: use it and make interactive placement working
* Take imported line width in account. Ensure DXF line thickness is OK.
* handling empty files in legacy mode.
This adds a check for contiguous board outlines to the DRC. It also
uses the calculated outline to ensure that traces are not crossing the
outlines.
Fixes: lp:1648055
* https://bugs.launchpad.net/kicad/+bug/1648055
Rather than duplicating the connectivity calculations in determining
whether a track is dangling, we utilize the current database to find the
number of connected items for an anchor item when feasible.
Multiple anchors such as tracks still need additional logic.
Fixes: lp:1805479
* https://bugs.launchpad.net/kicad/+bug/1805479
The client filter might add items in the case where locked pads are
filtered. We need to handle this case when requesting selection by
adding new items to the m_selection
Fixes: lp:1802686
* https://bugs.launchpad.net/kicad/+bug/1802686
When changing the track width, we need to allow that the track's route
will change based on DRC, so force a move without changing position.
Fixes: lp:1785057
* https://bugs.launchpad.net/kicad/+bug/1785057
When we draw a path, we usually want to close the path when clicking on
the end of another line. This uses grid helper to ensure this
progression happens as expected.
When updating the status of the ratsnest, we mark its target layer as
dirty to ensure the revised data are used to draw/clear the ratsnest
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit 50eedcf0b3)
JP notes that there is an issue with comma-based decimal locales and the
SaveSelection that is addressed by having a LOCALE_IO call in a limited
block.
This changed the copy timing of the clipboard and the interaction with
KDE Klipper again. To address this, we isolate the clipboard open call
to the end of the routine and force a round-trip of the clipboard data
before exiting.
Klipper seems to poll at odd times. When we copy to wxTheClipboard
in one locale and Klipper extracts data in a different locale, it throws
an XError. We don't need the extra LOCALE_IO calls as Format() uses its
own LOCALE_IO setting.
Fixes: lp:1800648
* https://bugs.launchpad.net/kicad/+bug/1800648
The ratsnest layer needs to be always enabled in GAL rather than taken
from the board settings. This also adds a finalize handler to the
picker tool that allows a picker-caller to perform a specific action
when the picker tool exits. In this case, we use it to clear the local
ratsnest selections back to the default.
Fixes: lp:1800301
* https://bugs.launchpad.net/kicad/+bug/1800301
(cherry picked from commit c0d9b9ab81)
When the local ratsnest tool is used, it should toggle the state based
on the global ratsnest visibility. After changing state, the layer
cache is marked as well.
Possibly related to lp:1800301
(cherry picked from commit 22fbf30f22)
This parameter defines the working area (full page) size.
The fix is not perfect, because it does not take in account the page size.
However it is similar to the "old" initialization, before Eeschema GAL.
In Eeschema, a reasonable boundary size is used.
Distinguish between the snap-from and snap-to items. Previously, we
used the SELECTED or DRAGGED flags but the flagging arcitecture was
inherently fragile. This specifies items directly that should not be
used as snap targets.
Fixes: lp:1802795
* https://bugs.launchpad.net/kicad/+bug/1802795
Filtering based on selection ignores the use case where we are measuring
to a selected item. This utilizes the dragged flag to prevent snapping
based on the current state of the item drag.
Fixes: lp:1801089
* https://bugs.launchpad.net/kicad/+bug/1801089
When snapping, we should allow any point identified as a snappable
point. The additional consideration for corners might be used for
alignment in the future.
Fixes: lp:1802741
* https://bugs.launchpad.net/kicad/+bug/1802741
Factor out save current canvas view to image file code from symbol editor
code so it can be used anywhere.
Add ability to save to any image format supported by wxBitmapType. See
https://docs.wxwidgets.org/3.0/gdicmn_8h.html#a90a1eb6d85b5044a99b706fd979f27f5.
Currently only PNG output is implemented.
Please note that there is a minor bug that appears to be due to the
scroll bars which causes unfilled areas on the right and bottom edges
of the image. This always existed in the save symbol editor view
image but it was not as noticeable because by default the background
color is white. It is very noticeable in the footprint editor with
a black background.
The usual smattering of coding policy and comment fixes.
Fixes lp:1802127
https://bugs.launchpad.net/kicad/+bug/1802127
If checkboxes don't have individual IDs FormBuilder won't assign
them and the event table ends up connecting each checkbox to all
of the checkbox handlers in the dialog.
Fixes: lp:1801746
* https://bugs.launchpad.net/kicad/+bug/1801746
Importing Eagle files allowed for invalid zone values for clearance and
minimum width that triggered asserts in the 3d-viewer.
Fixes: lp:1801188
* https://bugs.launchpad.net/kicad/+bug/1801188
Fedora packaging errors with ambiguous python shebang since current
rawhide (30).
So we should remove it as the footprint wizards are not to be executed
standalone.
Variable netBuffer contains all NET_INFO items, whereas max_netcode
value is determined only basing on pad nets. After a netlist update
there still might be a NETINFO_ITEM that is not assigned to any pad and
has a net code higher than calculated max_netcode. Such situation
results in a out-of-bounds access in sortNetsByNodes().
Separate out zone edges (which are quite specific, and should
win over most other things) from zone fills (which are pretty
generic and should only be considered when there's nothing else).
Also excludes zone fills when the zones aren't being shown as
filled.
Display GALs had an incorrect world unit value set. Now the world unit
value says how many internal units are in an inch, in accord with the comments
in the GAL header. Bitmap drawing code relied on the information about DPI,
so scaling worked differently for display and print GALs.
It is possible for an async thread to simply be deferred if not
specifically set to async. In which case, until the return value is
requested, the loop may simply wait.
By decoupling from std::thread, we can avoid the wait/sleep cycle in
checking the std::atomic completion variable. The std::future variables
are immediately returning without the additional atomic check cycle.
This minimizes the thread usage, particularly during online actions such
as moving items and routing.
UpdateRatsnest: Minimized the number of atomics by utilizing future
promise. Avoided updating node-less nets. Node-less nets are common in
the dynamic ratsnest because the net vector is created from the board
nets by value but only populated with a subset. So the dynamic ratsnest
calculation always saw every net as dirty and spun up extra threads.
searchConnections: ParallelThreadCount is no longer lower bounded.
Small item counts are handled inline rather than with a separate thread.
When processing the selection filter, items were deselected before being
reselected after passing through the filter. This adjusts the logic to
only deselect those items that are filtered out.
Some windows machines seem prone to sleeping for excessive times. When
called in the main thread, this may prevent the system from responding
to Windows 'Are you alive?' calls.
TF.FileFunction,Copper,L1,Top,Signal is now TF.FileFunction,Copper,L1,Top
This param is not useful, and probably never correctly set by users, because is is not used by Pcbnew.
(It is used only for dsn export)
The implementation relied on the fact that PyString_AsString is returning NULL
for invalid inputs (and causing an error condition), which is then fixed by the
call to FROM_UTF8. Now, we will simply return an empty string if Py_None is
returned by a python fuction, which resemebles the old behaviour of those methods
Rather than forcing each thread to iterate over the full nets list to
find the dirty items, we collect the dirty items first before asking the
threads to address them. This prevents thread spinning. We also
amortize the cost of calculating on an 8-net per thread basis rather
than 2.
Locks protect the std::set in each item. Devolving the mutex to the
CN_ITEM allows multiple threads to make simultaneous connections to
different items where they do not conflict.
The connectivity files were unwieldy. This separates them logically
into data, algo and items where the items classes are those that hold,
surprise, surprise, the items, lists and clusters.
Refactor the polygon event loop into its parent function to allow access
to the params structure. Active layer now updates the drawing layer for
add/cutout zones.
Fixes: lp:1797483
* https://bugs.launchpad.net/kicad/+bug/1797483
Dynamic casts should only be used when we explicitly check for the
resulting pointer to be NULL. Where we know the class is castable we
can use static_cast, save on overhead and ensure our resulting pointer
is non-null.
When using the board edit, align tool automatically moved footprints
instead of pads but distribute tool did not. This standardizes the
behavior.
Fixes: lp:1796997
* https://bugs.launchpad.net/kicad/+bug/1796997
The evaluation of count_if resulted in a 0 or 1, leading to segment zone
fills always running on single processor and the progress bar showing
incorrect status. Likely infrequently hit as only affected segment
fills.
Block rotate and mirror now work like they do in Pcbnew (that is
they're treated as part of the block move/duplicate/whatever
rather than finishing it).
Fixes: lp:1780794
* https://bugs.launchpad.net/kicad/+bug/1780794
If the user is carefully selecting the zone edge, we do not filter the
zone preemptively from our disambiguation list in the same manner as we
do for selecting on zone copper.
Fixes: lp:1796719
* https://bugs.launchpad.net/kicad/+bug/1796719
The board design settings file keeps our default values for various
thicknesses. We use this to replace a number of magic numbers with the
defined value to help self-document the code.
The check against S_POLYGON was always false because we set the default
type to S_SEGMENT. This unifies the magic numbers to the board design
settings file
Disabling the grid should leave the snapping in place. But our disabler
returned the current point as closest, effectively always ensuring the
cursor position was the closest snap. This only uses grid when
requested.
This is temporary until we figure out a way to do multiple constraint
handling in GRID_HELPER or the EC_* class. This will work as long as
the EC constraint helper places the endpoint on either the primary or
aux grid.
Fixes: lp:1796540
* https://bugs.launchpad.net/kicad/+bug/1796540
We no longer require this as we calculate the number of segments based
on the maximum deviation rather than fixed numbers.
Fixes: lp:1780518
* https://bugs.launchpad.net/kicad/+bug/1780518
Get the board settings when changing the drawing layer. These include
default line thickness that should be updated.
Fixes: lp:1796489
* https://bugs.launchpad.net/kicad/+bug/1796489
When drawing the crosshair should track the element while the mouse
provides the position to calculate the next snap.
Fixes: lp:1796524
* https://bugs.launchpad.net/kicad/+bug/1796524
The dimension tool is used to measure physical dimensions on the board
therefore it should be able to snap to any other object, not just those
on its own layer set as is the case for other items.
This also deals with a corner snap case for constraints by first
snapping, then constraining, then aligning to grid. This ensures OoO
for alignment from least to most constraining.
When considering potential targets for snap points, we need to exclude
the currently selected item as this will mean that we always snap to
ourselves when editing an existing item.
Fixes: lp:1796507
* https://bugs.launchpad.net/kicad/+bug/1796507
When drawing segments, the segment will be NULL'd after committing, at
which point we lost our snap layer. Choosing snap layers from the
current drawing layer is a more robust method.
Fixes: lp:1796467
* https://bugs.launchpad.net/kicad/+bug/1796467
Deselection by clicking on a zone makes working with plane zones easier
by allowing the selected item to de-selected by clicking on a zone.
Once the selection is cleared, the zone may be re-selected as normal.
Clicking on non-zone items while a separate item is selected will still
select the new non-zone item without requiring a second click.
Updating connectivity should not need to iterate over the full item list
in each thread. Instead, we collect the dirty items first and then
iterate only over the dirty list.
Our connectivity data threads the ratsnest update based on the number of
nets that have changed. If we are only changing one net (the case when
routing) then making a full thread to update the net is pointless
because we wait for the thread to finish before continuing. This spins
that off to an inline lambda for single updates while still making
threads for multiple ratsnest changes.
This shows the snap indicator even when the item we are snapping to
occurs on a grid point, giving the user an indication that the point is
correctly connected.
Many items require precise, non-grid movement. Adding the ability to
flag a non-grid option will permit this behavior.
This is a required precursor commit to fixing lp:1738818 and lp:1771683
The computeAnchors function is used to find best drag locations for
items being moved. All movable PCB items should be handled.
Fixes: lp:1794304
* https://bugs.launchpad.net/kicad/+bug/1794304
When requesting to move a footprint based on the pad, the pad layers
should determine the snapping. This extracts layers from the selected
pad before allowing the filtering for locked pads
Fixes: lp:1787627
* https://bugs.launchpad.net/kicad/+bug/1787627
Since we are handling snapping in the grid helper, we don't need to
enable it in the cursor position return. This allows the grid helper to
use the frame position while optionally snapping to segments.
Put the cursor and pan control TOOL_ACTIONs in ACTION,
and refer to them in that way.
The handlers are currently identical in Pcbnew and Cvpcb,
and Gerbview (and all canvases) can benefit from them as well
if they are in libcommon. Also saves duplicated code.
Fixes: lp:1795855
* https://bugs.launchpad.net/kicad/+bug/1795855
This ensures that when starting to draw a zone or graphic element, the
preview is drawn in the same color/on the same layer as the element that
will be created. Previously, beginning a graphic polygon while a copper
layer was active would result in the preview being drawn in the color of
the active copper layer.
Adds Cut/Copy/Paste and Revert for footprints; introduces a new
shared Revert Changes? dialog; hooks up Add Library for footprints,
standardizes the Save As terminology.
Polygon corners were enabled in the footprint editor but the logic
didn't extend to the board editor. This revises the logic to look for
DRAWSEGMENTs and only reference the PCB_MODULE_EDGE_T where needed to
create a new segment in the footprint.
Fixes: lp:1782966
* https://bugs.launchpad.net/kicad/+bug/1782966
Allows selection of polygons and zones by their visible area. Will only
select polygons/filled areas when they are unobstructed by other
elements in the footprint/pcb. Also adds a "skip heuristics" modifier
key for clicking (ALT) that allows the full disambiguation list to be
displayed without removing less-likely elements. This dovetails the
zone/polygon selection as it allows selecting even when areas a fully
overlapped.
Fixes: lp:1753153
* https://bugs.launchpad.net/kicad/+bug/1753153
Seth Hillbrand
jean-pierre charras
Jeff Young
Jon Evans
Michael Kavanagh
John Beard
Wayne Stambaugh
Tomasz Włostowski
Thomas Pointhuber
Maciej Suminski
D4p0up
nats
Nick Østergaard
Roman Beranek