21b80949ff
Compile with -Os as default. Change like "make OPT_FLAGS=..."
...
SWD/JTAG Bitbang is compiled with -O3 for good bitbang speed.
2021-04-20 18:20:41 +02:00
f55ad67b1b
adiv5: catch timeout on adiv5_ap_read_id and abort
...
This adds a TRY_CATCH around the adiv5_ap_read_id() in
adiv5_component_probe() and resets the DP when that happens.
It seems like the STM32WLE5 comes with the AP of the inactive core
enabled in a way that does not make it detectable, and the current code
times out and leaves the whole device hanging.
Catching the timeout and calling adiv5_dp_abort() seems to restore the
device to a useable state.
Tested on Seed LoRa-E5 (STM32E5JC).
2021-04-19 16:57:13 +02:00
806787529f
Use DMA for USBUSART TX/RX
2021-04-17 17:57:08 +02:00
cf5b4afb38
bmp_serial/linux: Honor opt_list_only (-l).
2021-04-17 16:19:57 +02:00
d6b24c00c8
Fixed STM32G43x/G44x option bytes support
...
Previously took L4 values so FLASH_SEC1R was not applied
2021-04-17 14:44:30 +02:00
99f9557cc0
Support for STM32G49x/G4Ax (category 4)
2021-04-17 14:44:30 +02:00
c85c946ce3
PRIx32 fix
2021-04-17 14:44:30 +02:00
9ec7d05d8d
Put null terminating characters when scanning for BMP probes on linux
...
This patch puts null terminating characters for the 'type',
'version', and 'serial' strings extracted from blackmagic probe
id strings on linux systems.
2021-04-17 14:41:28 +02:00
299da8627c
libftdi: Remove unneeded explicit path.
2021-04-17 13:35:21 +02:00
a6a8606edb
STM32L55: Detect, memory map, read and flash write. Options handling missing.
...
Only non-secure states considered!
2021-04-04 17:26:31 +02:00
739941dc5f
Verify right after programming
2021-03-31 13:06:52 +02:00
2982888b66
BMP_MODE_FLASH_WRITE_VERIFY combined operation
2021-03-31 12:07:53 +02:00
f85c54be97
Prepared -w option
2021-03-31 12:07:53 +02:00
6d6cfd6c98
Comprehensive STM32G03/4/5/6/7/8/B/C driver
2021-03-29 21:42:40 +02:00
58f153e12b
cortexm: Always halt and release reset before romtable scan
...
Only release from halt once after romtable scan
Should fix #836 .
2021-03-26 17:43:11 +01:00
a025c9a7bd
Revert "stm32f1: On ST parts there is no need to read IDCODE again."
...
Romtable partno is not unique for devices, e.g. in STM32F0
This reverts commit f89b07d892
2021-03-26 17:35:00 +01:00
f89b07d892
stm32f1: On ST parts there is no need to read IDCODE again.
...
IDCODE is already known from the Romtable
Probably this has the same effect as #836
2021-03-12 20:45:34 +01:00
e6a9a1a366
cmsis-dap: Get the firmware version.
2021-03-06 13:30:09 +01:00
7859a2aabd
adiv5_swd: Factor out creation of packet request.
2021-03-06 13:30:09 +01:00
cfb784d428
adiv5: Fix comments and debug output
2021-03-05 16:49:19 +01:00
3aa6f16964
serial_unix: Split timeout in seconds and microseconds
...
Macos exposed errors when tv_usec was > 1000000.
2021-03-05 16:49:19 +01:00
43770736f1
cl_utils: Rework Flash/Ram printout
2021-03-05 16:49:19 +01:00
560a046a22
Add support for NXP LPC802, LPC804, LPC832 and LPC834
2021-02-22 19:37:46 +01:00
0df44e205b
ADIv5: Abort Romtable scan also if CIDR0 is invalid after halting #832
...
STM32WLE5 has the same dual core chip as STM32WL5. For the second
core, the additional AP can be see, but access to e.g. CIDR0 for that
Romtable fails.
Aborting the scan too if again the second read of CIDR0 fails makes
sense anyways!
2021-02-19 18:48:02 +01:00
d70fa8c7f6
hosted: Remove restrictions when gathering information on the debugger
...
That way, we find RPI Pico pico-debug.
2021-02-15 17:47:29 +01:00
c776e7a9a6
swd_scan: Add '-m' as targetid argument to swd_scan to prepare multi-drop.
...
In a real multi-drop setup, the device to use must be specified.
2021-02-15 17:47:29 +01:00
8e2f6937d5
hosted: Run target specific monitor commands with -M "command" .
...
Lists available commands: "blackmagic -M help"
Quote multi argument monitor commands, e.g. STM32F1: blackmagic -M "option help"
2021-02-15 17:47:29 +01:00
165560edd8
cl_utils: target selection '-n' argument needs optarg.
...
foreach now returns the number of targets.
2021-02-15 17:47:29 +01:00
4eb336277c
native: Remove high current draw ( #814 )
...
Special iRST_SENSE handling does not apply at least for BMP 2.1c.
On V2.1c, iRST_SENSE was set as output high and xRST high shorted
iRST_SENSE to ground via Q2
FIXME: Check for older versions!
2021-02-15 15:00:19 +01:00
3b8502c2e5
add space in USB product string (be consistent with ../stm32/dfucore.c)
...
This changes the USB identification from
"Black Magic Probe(STLINK/V2) v..." to
"Black Magic Probe (STLINK/V2) v..."
Signed-off-by: Martin <Ho-Ro@users.noreply.github.com>
2021-01-29 14:47:28 +01:00
d4dc3b2717
The USB CDC is no modem and does not use the AT protocol
...
Signed-off-by: Martin <Ho-Ro@users.noreply.github.com>
2021-01-29 14:47:28 +01:00
42f590ce0b
fixing some memory map errors for stm32h7, PR #821
2020-12-23 20:10:39 +01:00
09c000eca8
hosted: Really handle setting tpwr on remote on the command line #817
...
Expect the command to fail, due to old firmware or remote not implementing
the power switch.
2020-12-19 16:36:09 +01:00
2b06f045c4
target: kinetis: add S32K148
...
This adds support for the NXP S32K148. This is an automotive-grade part
that is derived from the Kinetis line, so it has a very similar
interface to other parts in the family.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-12-16 12:49:23 +01:00
5f76169b95
hosted: remove ftdi include when built with BMP_ONLY #811
...
Signed-off-by: Sean Cross <sean@xobs.io>
2020-12-16 11:30:42 +01:00
98c92a6d18
hosted: Really fix the case of no serial number ( #807 )
2020-12-13 14:12:05 +01:00
aa0d8f4b5d
Merge pull request #783 from UweBonnes/frequency
...
Frequency
2020-12-12 19:50:53 +01:00
020600aa56
target/lpc546xx: fix lpc546xx flash support ( #801 )
...
**Summary**
Modifications to fix flash support on the lpc546xx:
- fix IAP entrypoint to be `0x03000204`, not the value at that address
- add a reset and attach sequence before erasing flash sectors. there's
little documentation around this, but experimentally, erasing sector 0
fails when the ROM bootloader is mapped to it (on reset). stepping the
chip once and attaching is enough to snap the chip out of it, permitting
flash erase on sector 0.
- add a few test commands to the lpc546xx table (read_uid, erase/write
sector, etc).
- write the magic CRC value when writing to sector 0
(`lpc_flash_write_magic_vect`).
- move the lpc546xx probe to before the lpc43xx probe, to prevent
getting the lpc546xx into Lockup when reading an illegal memory location
during lpc43xx probing
Fixes #786 .
I don't 100% understand the reset/load sequence of this part, but these
changes are sufficient to program and debug the part now.
I didn't do a detailed analysis of what pyocd (via st-link hardware
adapter) and segger jlink do to handle the same, but both of those
worked without modification, so there's some difference in the
sequence they're using.
**Testing**
Verified I can now successfully erase and write an executable in sector
0 (and other sectors).
Verified the new commands work correctly.
2020-12-12 19:48:05 +01:00
6dbb5ff7ee
Frequency: Implementing for jlink.
...
SWD frequency is fixed for jlink according to the docs from 2010.
2020-12-12 18:33:09 +01:00
fdc654cfb3
stlink: Implementation of frequency setting.
2020-12-12 18:33:09 +01:00
de26ba6f73
hosted: Add is_jtag to the info structure
...
Needed for different frequency setting procedures on some platforms.
2020-12-12 18:33:09 +01:00
28a966a3e6
frequency: Implement for ftdi.
...
For all 2232H types, use undivided 60 Mhz.
FIXME: Check FT2322C/D for unsymetric clock at 6 MHz!
2020-12-12 18:33:09 +01:00
13e8a262e4
SWJ Frequency: Implement for cmsis-dap
2020-12-12 18:33:09 +01:00
1ca9f234f7
Infrastructure for setting maximum SWJ frequency.
...
Implement for BMP/firmware on STM32.
2020-12-12 18:33:09 +01:00
7365a44989
hosted: Implement SWJ test mode (-T).
...
Continious read/write-back some core register as NOP operation to allow scope
measurement of SWJ timing.
2020-12-12 18:33:09 +01:00
f796b774bd
hosted: Fix info.serial if USB device has no serial number #807
2020-12-12 18:32:15 +01:00
518529a772
Support GD32E23x
2020-12-12 18:29:30 +01:00
14498decd9
HOSTED_BMP_ONLY/linux: Fix case when no serial device is connected #806
2020-12-12 15:06:26 +01:00
93d4c65948
Fix building with newer GNU make( #804 )
...
More recent versions of GNU make remove the `-` prefix from
`$(MAKEFLAGS)`, which breaks the build:
```bash
# output truncated to interesting parts
> make -C src --trace all_platforms
set -e ;\
mkdir -p artifacts/v1.7.1-91-g98b4ec5 ;\
echo "<html><body><ul>" > artifacts/index.html ;\
for i in platforms/*/Makefile.inc ; do \
...\
make w --trace --no-print-directory clean ;\
make w --trace --no-print-directory;\
...\
done ;\
echo "</ul></body></html>" >> artifacts/index.html ;\
cp artifacts/*.bin artifacts/v1.7.1-91-g98b4ec5
Building for hardware platform: f4discovery
make[1]: *** No rule to make target 'w'. Stop.
```
Per the
[documentation](https://www.gnu.org/software/make/manual/html_node/Options_002fRecursion.html ),
there's no need to manually apply insert `$(MAKEFLAGS)`, it should be
automatically included when using `$(MAKE)` when recursing.
I tested on my machine (make 4.2.1) and a docker image based on
ubuntu:trusty (make 3.81), both behaved the same (directories were not
printed when recursing by default);
2020-12-12 14:39:52 +01:00
b5172cf6df
Implement the 'find_debuggers()' function for hosted BMP on windows.
2020-12-11 18:36:48 +01:00
01f8628aed
Bugfix in detecting BMP probes by usb serial number.
2020-12-11 18:36:48 +01:00
170fe0c368
Remove spurious comment.
2020-12-11 18:36:16 +01:00
4c5ce0b16a
Hosted: Handle devices w/o serial number, e.g. GigaDevices GD-Link ARM/CMSIS-DAP
2020-12-11 18:36:16 +01:00
0f1fe9e438
hosted/linux: Find BMP devices without libusb.
2020-12-11 18:36:09 +01:00
bd5f4c6ed5
hosted: Consolidate ident output.
2020-12-11 17:55:31 +01:00
0870b778c0
hosted: Allow to build without libusb, libftdi and hidapi with HOSTED_BMP_ONLY=1
2020-12-11 17:50:16 +01:00
32db38ecf2
hosted/libusb: Move platform.c libusb related functions to own file.
2020-12-11 17:35:43 +01:00
41788f923b
ftdi/stlink/jlink: Provide dummy functions in the HOSTED_BMP_ONLY case
...
Do not allow multiple inclusion by not declaring the functions as static to
help keep code clean.
2020-12-11 17:31:25 +01:00
98b4ec58bc
Update to recent libopencm3 to undo unwanted change.
2020-12-07 21:51:22 +01:00
633c6a2e81
Recognize "J-Trace Cortex-M PRO V2" in hosted mode
2020-12-07 11:52:33 +01:00
17dfec3572
dfu/cdcacm: Consolidate usage of ST vs BMP serial number.
2020-12-06 15:18:08 +01:00
5c7e0eedb0
command.c: Consolidate "mon version" output
2020-12-06 15:18:08 +01:00
07c3699225
version.h: Remove from platform.h files
...
- Consolidate ident string generation
- Recompile only needed files
2020-12-06 15:18:08 +01:00
dd6aadc54d
jtag: Add verbosity about devices found.
2020-12-06 15:18:08 +01:00
0a7bfd5923
dfu_f4: Fix sector_erase.
2020-12-06 15:18:08 +01:00
e318f884bf
Change the type of 'cortexm_wait_timeout' to unsigned.
...
It makes sense that the timeout value is unsigned, it also
resolves build errors on some platforms.
2020-12-04 11:44:50 +01:00
c9a419e44b
Correct loss of sync protocol error #787
2020-12-04 11:33:23 +01:00
e3fd12ebc6
gd32f1/f3 detection and ram/flash autoset
2020-12-03 11:16:47 +01:00
575c25e570
Add support for STM32F1 clone with new AP_DESIGNER id
2020-12-01 10:23:16 +01:00
48a79ff9da
adiv5: More checks for a sensible DPIDR.
2020-11-29 21:11:11 +01:00
752bc26536
adiv5: Fix memleak with duplicated base.
2020-11-29 21:11:11 +01:00
acec489647
adiv5_jtagdp: Always set idcode.
2020-11-29 21:11:11 +01:00
9e1b7fdac0
jlink/swd_low_access: Fix data direction during response read phase.
2020-11-29 15:48:50 +01:00
8903026c14
jlink/swd: swd frequency is fixed, not need to set.
2020-11-29 15:48:50 +01:00
f45c56af83
adiv5/swdp: Check early for valid DP idcode.
2020-11-29 15:48:50 +01:00
3b6432912d
jlink: Catch another error with no target connected.
2020-11-29 15:48:50 +01:00
7df314e265
Firmware/Jlink: Fix double free when debug power-up fails ( #780 )
2020-11-29 15:48:50 +01:00
e1329499de
platform_adiv5_swdp_scan: Do not double free with early errors.
...
adiv5_dp_init() clean up itself if errors happen
2020-11-29 15:48:50 +01:00
bf548e92c0
swd: After write low_access, always append 8 clk to move data through SW-DP.
...
Especially needed when leaving the debugger or during debug unit power-up.
ARM Debug Interface Architecture Specification ADIv5.0 to ADIv5.2
tells to clock the data through SW-DP to either :
- immediate start a new transaction
- continue to drive idle cycles
- or clock at least 8 idle cycles
Implement last option to favour correctness over slight speed decrease
Implement only for adapters where we assemble the seq_out_parity in our code,
as on firmware, ftdi and jlink. Hopefully the high level adapters do it right.
Reverts 2c33cde63fcde7726b87
2020-11-27 22:26:48 +01:00
139e5d7e22
f4discovery: Compile time option to compile with ST bootloader
...
Just to keep things active. Prepare for F72 bootloader.
2020-11-27 22:26:48 +01:00
636bcee355
stlink/swlink: Remove the DFU upgrade utility.
...
Hopefully no old bootloaders are around. If otherwise, revert to last
commit before this and update the DFU bootloader.
2020-11-27 22:26:48 +01:00
27ef4569ca
stm32/dfucore.c: Use libopencm3 provided defines and functions.
2020-11-27 22:26:48 +01:00
9d55128ab8
cl_utils: Get voltage only once.
2020-11-27 22:26:48 +01:00
e6823f39de
Hosted: Print version with "-h" and "-t" option.
2020-11-27 22:26:48 +01:00
3ee31473c6
cortexm.c: LPC15xx has designer 43b and Partno 4c3
...
Thanks to JojoS!
2020-11-27 22:26:48 +01:00
62d9f60f03
hosted/firmware: Waits for read response as long as cortexm_wait_timeout.
2020-11-27 22:26:48 +01:00
26a23dd1cb
stlinkv2: Try harder to open an AP.
...
Problem seen on STM32L0 with probably long sleep periods.
2020-11-27 22:26:48 +01:00
19e1fddba2
adiv5: Remove unnescessary read.
2020-11-27 22:26:48 +01:00
cda83d3084
Fix memleaks.
...
Happened e.g. when Stlink could not enter debug or when cortexm_prepare timed out.
2020-11-27 22:26:48 +01:00
9ac5adfcef
adiv5: Additional decoding.
2020-11-27 22:26:48 +01:00
d78d7838d3
stm32f1: Always read DBGMCU_IDCODE for t->idcode ( #770 )
...
At least STM32F042 has 0x440 as romtable partno vs 0x445 as DBGMCU_IDCODE.
Thanks to Andrey Melnikov(aam335) for pointing out!
2020-11-27 22:26:48 +01:00
653d486ee2
cortexm: Store CPUID in target structure.
2020-11-27 22:26:48 +01:00
824a1d8abc
hosted/find_debuggers: Do not check hubs. Print class of devices unable to open.
2020-11-27 22:26:48 +01:00
e68dd25813
cl_utils: Clarify -d option is BMP/firmware only and deprecate -d.
2020-11-27 22:26:48 +01:00
f71e18948a
GPIO for SWD: Slow down edges on more platforms.
2020-11-27 22:26:48 +01:00
80154c5c7a
adiv5_swdp: Fix more memory leak.
2020-11-27 22:26:48 +01:00
35bcb4f7c6
Switch on the lpc546xx target
...
Enable the lpc546xx target. Tested on the LPCXpresso54628 dev board,
able to flash and debug.
2020-11-24 21:32:39 +01:00
e9c02296f2
target: kinetis: add S32K118
...
This adds support for the NXP S32K118. This is an automotive-grade part
that is derived from the Kinetis line, so it has a very similar
interface to other parts in the family.
Signed-off-by: Sean Cross <sean@xobs.io>
2020-11-14 13:06:23 +01:00
f18be6ef7a
Add support for Kinetis K12 and placeholders for other K-series MCUs
2020-11-07 12:44:05 +01:00
2c33cde63f
cortexm.c/cortexm_halt_resume: Add some clock cycles to always get CPU going ( #768 )
2020-11-01 21:53:23 +01:00
d75f3124b9
ftdi_bmp.c: Reapply fix from #715 : Check for libftdi 1.5
2020-11-01 12:09:27 +01:00
99142d1c0e
Add documentation details for building PC-hosted BMP in msys2.
2020-11-01 11:33:54 +01:00
1f7a716710
adiv5.c: Run cortexm_prepare on all suspected CortexM instances.
...
Gets all debug units of the second CPU of a STM32H745 visible.
2020-10-23 09:40:15 +02:00
18673d9a56
adiv5: Rework DP/AP refcounting.
...
ASAN non longer reports leaks with the STM32H745.
2020-10-23 09:40:15 +02:00
f76a7c4e92
adiv5: Release devices after scan.
...
Before, scanning only kept device stopped until POR or attach/detach cycle.
2020-10-23 09:40:15 +02:00
73e6b540b2
command: When debug channel is available, print morse messages readable.
2020-10-23 09:40:15 +02:00
776861c6a0
Makefile: Fix version.h generation for make all_platforms
...
Same fix as 0ae65cc10f
2020-10-23 09:40:15 +02:00
80ddafc2f8
Jtag/High Level : Transfer dp->dp_jd_index with every HL command.
...
- Add REMOTE_HL_VERSION, now at 1. Fall back to hosted/low-level
when wrong version is found and give hint to user.
2020-10-23 09:40:15 +02:00
59dc1b7eb4
cortex-m7: Give hint about buggy core revision.
2020-10-23 09:40:15 +02:00
976c763747
jtag remote: Start fixing handling M0 (second jtag) for LPC4322 in high-level
...
- LPC11: Only print none-null unknown idcodes.
2020-10-23 09:40:15 +02:00
0995fe1288
cmsis-dap: Various fixes
...
- decrease report size to 64, otherwise MIMRXT10x0-EVK crashed when
reading larger memory block
- dp_read_reg acts direct, fixing CortexM core register read.
- length of data to write with read_block.
2020-10-23 09:40:15 +02:00
f15b1d7763
cl_utils: Clip opt_flash_start only when not set.
2020-10-23 09:40:15 +02:00
c161521c26
cortexm: Designer ARM must be in the default path when probing.
2020-10-23 09:40:15 +02:00
cdd07544d5
Cortexm: Allow pure debug on devices not yet handled for flashing
...
- Recognize STM32L552 and MIMXRT10XX
- Fix another PIDR
- Fix bad debug print string.
2020-10-23 09:40:15 +02:00
3270138ec2
Revert 69e577c9243ce027b628e96881ce2416213fef43
...
What was thought to be a typo is apsel = 0xff for a dp access.
2020-10-23 09:40:15 +02:00
77c4f9d702
stlink: Rework README.md
...
- Document flashing BMP Firmware and reverting to ST firmware
- Consistant nameing
2020-10-19 14:13:29 +02:00
9cd3193a89
bmp_remote.c: Fix bug introduced with 8b929c12c9.
2020-10-17 12:49:37 +02:00
0ffb4f7b18
cortexm: Fix protected SAM detection
...
- Only run cortex_prepare() if reading cidr fails
- With Atmel DSU detected, run cortexm_probe()
2020-10-17 12:49:37 +02:00
5bc743d221
samd: Propagate security after setting security by chip reset.
2020-10-17 12:49:37 +02:00
8b929c12c9
hosted/jtag: Transfer jtag_devs to firmware.
2020-10-16 20:03:03 +02:00
3d92b82678
jtag: Use index and not device structure for jtag_dev_write_ir and jtag_dev_shift_dr
2020-10-16 20:03:03 +02:00
6e2a074064
bmp_remote: Deny high level JTAG for now.
...
jtag_devs and jtag_dev_count needs to be known on th firmware side
and remote_dp->dev needs to be filled with jtag_dev_t.
2020-10-16 20:03:03 +02:00
0f5fb6b9a0
remote: Initialise dp_read and low_access with SWD_INIT.
...
Before "mon s" after "mon j" failed.
2020-10-16 20:03:03 +02:00
752d14ca3e
remote.c: Add comments.
2020-10-16 20:03:03 +02:00
ba26adce53
remote.h: Remove typo.
2020-10-16 20:03:03 +02:00
7ccf0d3e03
jtag_dev_t: Make dev, idcode and desc less generic.
...
No codechange intended.
2020-10-16 20:03:03 +02:00
87b546777a
nrf51: Be more verbose about the protection status.
2020-10-16 12:16:33 +02:00
4108b649c2
stm32h7: Add support for new product lines
...
Add support for:
* STM32H7B3/B0/A3 (RM0455)
* STM32H723/33/25/35/30 (RM0468)
Successfully tested with:
* STM32H7A3ZIT (RM0455)
* STM32H747XIH (check for regressions)
2020-10-10 22:09:34 +02:00
817c62d7fd
Merge pull request #507 from UweBonnes/cortexm_romtable
...
Cortexm romtable
2020-10-08 10:53:17 +02:00
877b4be8ee
cortexm: Restrict probing by using the ap_designer.
...
More designers need to be observed and reported by users and added.
Request users to send needed data.
2020-10-07 20:12:35 +02:00
91d1ef8bf6
target/stm32: Use t->idcode with probe.
2020-10-07 20:12:35 +02:00
44bfb62715
Adiv5: Print Designer/Partno when device is not recognized
...
t->idcode is now 16 bit.
2020-10-07 20:12:35 +02:00
c456fc7f61
adiv5: Store AP designer and partno in the AP structure.
2020-10-07 20:12:32 +02:00
159196c2ad
Cortexm: Remove forced_halt.
2020-10-07 20:11:33 +02:00
9bb2807706
adiv5/romtable: Prepare CortexM devices to read the ROMTABLE
...
It seems, writing to DHCSR fails silent when the device is sleeping.
Reading DHCS during sleep may return nonsense.
Repeated write may at some point catch the device running and succeed.
With devices sleeping for long time and running on faster clock the
chance for a successful hotplug gets smaller.
- Try hard to halt a sleeping device
- Prepare vector catch and enable all debug units by TRACENA
- Release reset
- Apply device specific fixes
-- STM32F7: Store old value of DBGMCU_CR, enable debug in sleep in
DBGMCU before reading PIDR and restore DBGMCU on detach.
Signed-off-by: Uwe Bonnes <bon@elektron.ikp.physik.tu-darmstadt.de>
2020-10-07 20:11:17 +02:00
a254bc6308
Fix icdi usb error https://github.com/blacksphere/blackmagic/issues/740 https://github.com/blacksphere/blackmagic/pull/748
2020-10-07 18:08:04 +02:00
ceaee2a11e
hosted: Hint about BMPs in bootloader mode.
2020-10-07 17:12:22 +02:00
dc8924a2bc
stm32h7: Don't tc_printf from flash functions ( #747 )
...
* stm32h7: Don't tc_printf from flash functions
Receving an 'O' packet while flashing confuses GDB and then
weird stuff happens.
* Replace tc_printf with DEBUG_WARN
2020-10-05 10:45:18 +02:00
9bba3165fb
swdptap: Turnaround immediate after a reading with parity.
...
Thanks to JojoS.
Probably mostly cosmetic, but is keeps the device from driving SWDIO
until the next commands.
2020-10-02 10:51:14 +02:00
4d18496a6f
hosted: Allow to disable high level commands for BMP.
...
Useful for tracking low level problems on native with hosted.
2020-10-01 15:49:21 +02:00
014abf6cc9
adiv5.c: Reduce number of errors if reading cidr fails.
2020-10-01 15:33:28 +02:00
be40d2b851
adiv5: Check Debug Base Address early
...
Reduces printout when scanning the romtable
2020-10-01 15:22:17 +02:00
747336e927
f4discovery: Slow done JTAG pin slew rate to avoid ringing #742
2020-10-01 15:06:16 +02:00
38bc5bbf82
Add LPC546xx support #741 #553
2020-09-30 12:56:53 +02:00
2fdd94adeb
STM32F7: Add another missing Arch ID.
2020-09-24 16:20:34 +02:00
0ae65cc10f
src/Makefile: Fix version.h generation.
...
It seems, some git behaviour change got by unnoticed.
2020-09-22 19:02:26 +02:00
61d919c1ac
libftdi: Remove no longer needed workaround for travis CI.
2020-09-20 14:10:37 +02:00
77231e8972
serial_no: Fix error with "mon trace" #732
...
launchpad-icdi: Allow to set a serial number with make
2020-09-20 13:23:52 +02:00
bdb351a6ea
adiv5_swdp: On ACK_FAULT, error() and try again once #731
...
when writing CSW.
2020-09-18 20:07:32 +02:00
a4a934f461
Add comments for hardware revision of v2.1
2020-09-17 11:54:19 +02:00
Uwe Bonnes
Fabio Baltieri
Vestrel
fabalthazar
Stoyan Shopov
Thiadmer Riemersma
Martin
Alex Norman
Sean Cross
Noah Pendleton
Aaron Lindsay
Noah Pendleton
Emilio Lopes
mean
Jonathan Giles
jbuonagurio
Richard Meadows
David A. Aguirre Morales
Gareth McMullin
Eivind Alexander Bergem
jxltom