The primary display is the power factor, the secondary is the frequency.
This got mixed up, so change the order. We also need to fix the
conversion factor.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
is_power_apparent_power is index 0 of function 0x39, so it is better to
process it first and the later indices after that (we need to add
another one with a different patch later).
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Testing showed that AC current needs to be handled different from DC.
Note that ACA is still untested because of limited testing equipment.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
It was confusing to see the display value (5 digits) printed in debug
output as a float. Print it the same way as shown on the real device,
without comma, of course.
This also allows to simplify the code a little.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This g_close(), the only one in the whole code-base, would unnecessarily
raise the minimum glib version to 2.36.
Thanks to Daniel Glöckner for the report.
This fixes bug #724.
This function replaces the pattern of calling config_list() with
SR_CONF_DEVICE_OPTIONS to obtain a list of device options. Note
that this does not include the SR_CONF_{GET,SET,LIST} bitmask,
which is now retrieved for a specific key by calling
sr_dev_config_capabilties().
Refactor handling the size of modbus_devs, so it doesn't produce a build
warning and still allows the compiler to remove unused code.
This fixes bug #637. It could be reverted once modbus_devs
unconditionally has a member in the struct.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
In some situations, the reply to the *IDN? command contains an
additional trailing 0x01 byte for unknown reasons.
This issue seems to be reproducible by changing the voltage using the knobs
on the device, then turning on the output and turning it off again.
The next korad-kaxxxxp scan() operation would contain the trailing 0x01
byte, which would lead to the detection of the device in libsigrok no
longer working until the next power-cycle.
Work around this issue by treating both the ID string with and without
the trailing 0x01 byte as valid.
This is a desperate measure to improve the success rate of device
initialization even after it got into a bad state. Combine this
with a reduced USB timeout (1 second) so that if it fails, it fails
quickly. Also ignore USB errors from the initial dummy read of the
device test ID.
Detect whether the FX2 firmware of the LWLA device exhibits the
short transfer bug. If so, work around the problem by limiting
reads to at most 64 bytes at a time. This slows down the memory
read after acquisition quite noticably, but makes the device
usable even in adverse conditions.
Reduce the number of long registers read in bulk during status
polling from 10 to 5. The LWLA1034 driver used to do that already
in an earlier iteration, which was then changed to be more like
the original vendor software. The reason for bringing it back now
is that it reduces the response size to 40 bytes, which works
around the spurious 64 byte limit bug in the FX2 firmware of the
LWLA devices.
The sr_input_dev_inst_get API documentation guarantees an input is fully
initialized as soon as the device instance is returned. An sdi
implementation should not set sdi_ready any earlier.
This fixes parts of bug #387.
The sixth character from ISET? is read and discarded. If the device is
turned off and on again, this won't be there and causes 10 ms delay in
every ISET? Luckily, this value isn't queried that often. To get the
sixth byte, the *IDN? command has to be issued before ISET?.
==18779== 800,000 bytes in 196 blocks are definitely lost in loss record 29 of 29
==18779== at 0x4C29110: malloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==18779== by 0x4E635C3: receive (analog.c:319)
==18779== by 0x40870B: datafeed_in (session.c:316)
==18779== by 0x4E59D4E: sr_session_send (session.c:1201)
==18779== by 0x4E59F8B: sr_session_send (session.c:1159)
==18779== by 0x4E62595: send_chunk (wav.c:234)
==18779== by 0x4E62A06: process_buffer (wav.c:290)
==18779== by 0x40954A: load_input_file_module (input.c:123)
==18779== by 0x4097AB: load_input_file (input.c:157)
==18779== by 0x40531E: main (main.c:288)
==17549== 32 (16 direct, 16 indirect) bytes in 1 blocks are definitely lost in loss record 22 of 39
==17549== at 0x4C29110: malloc (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==17549== by 0x5359200: g_malloc (in /usr/lib64/libglib-2.0.so.0.4200.2)
==17549== by 0x536EE2D: g_slice_alloc (in /usr/lib64/libglib-2.0.so.0.4200.2)
==17549== by 0x5370165: g_slist_append (in /usr/lib64/libglib-2.0.so.0.4200.2)
==17549== by 0x4E595C3: sr_session_datafeed_callback_add (session.c:512)
==17549== by 0x409527: load_input_file_module (input.c:111)
==17549== by 0x4097AB: load_input_file (input.c:157)
==17549== by 0x40531E: main (main.c:288)
==7478== Invalid write of size 8
==7478== at 0x4E59182: sr_session_dev_remove_all (session.c:302)
==7478== by 0x4E591CD: sr_session_destroy (session.c:265)
==7478== by 0x4095D9: load_input_file_module (input.c:143)
==7478== by 0x4097AB: load_input_file (input.c:157)
==7478== by 0x40531E: main (main.c:288)
==7478== Address 0x7877eb8 is 88 bytes inside a block of size 96 free'd
==7478== at 0x4C2A37C: free (in /usr/lib64/valgrind/vgpreload_memcheck-amd64-linux.so)
==7478== by 0x4E5F454: sr_input_free (input.c:573)
==7478== by 0x4095C3: load_input_file_module (input.c:140)
==7478== by 0x4097AB: load_input_file (input.c:157)
==7478== by 0x40531E: main (main.c:288)
Do not use size_t for values whose width is defined by the device,
not the host. Also don't use size_t for simple indices with known
small range, unless type compatibility considerations apply.
Refactor the sysclk-lwla driver to separate the generic logic from
the model-specific implementation. Based on this, implement support
for the SysClk LWLA1016 device.
On some systems it can happen that the USB 'bus' number is a lot larger
than 64, but sr_usb_find() currently errors out if it is > 64.
Example:
Bus 250 Device 006: ID 1ab1:04ce 1ab1 DS1000Z Series[...]
Increase that limit so that the code will work everywhere. This bus number
is queried via libusb_get_bus_number() which returns an uint8_t, so we're
limiting to 255 here.
Thanks to 'ssi' on IRC for reporting the issue.
Apparently (some versions of) Mac OS X have the same problem with
usb_get_port_path() as FreeBSD does. Work around this in the same way.
Thanks to hanyazou@gmail.com for the patch!
This fixes bug #673.
The driver should now be able to cope with e.g. multiple ChronoVu LA8
and/or ChronoVu LA16 devices being connected to the same PC.
It now also provides the serial number and connection ID, which can be
used by frontends to differentiate multiple devices.
Also improve the scanopts / drvopts / devopts lists handling.
This fixes bug #504.
With the current driver API and the corresponding session event
handling, it is not possible to destroy and then re-create an
event source with the same key within the same main loop iteration.
The next generation driver API will fix this problem. But for now,
just change the driver to make do without that sort of thing. Also
increase the I/O timeout to 100 ms to be safer in the event of all
kind of delays the OS environment may induce.
This fixes bug #678.
Evaluate all 64 bit of the duration field in the capture status
record. Although unlikely in practical use, due to compression
it is possible for the duration in ms to exceed 32 bit.
zip_discard() was introduced in libzip 0.11, which some systems
do not have yet. Provide a fallback replacement for zip_discard(),
and reduce the requirement to libzip 0.10 again.
This fixes bug #674.
During initialization of the LWLA1034, read the 64-bit test word
twice and verify the result of the second read only. This better
matches what the original vendor software does.
Apparently, these four registers form an interface for indirect
access to another internal 64 bit wide memory. This is likely the
same memory as that accessed by the bulk transfer commands 7 and 8.
Added support for SR_CONF_REGULATION which returns value for CH1
Also VELLEMAN LABPS3005D (only device currently supported) sends single
'M' character in beginning of return value, which is specially discarded.
Trying to configure an invalid capture ratio would reset the
previously configured value. Instead, we should just reject the
new value and keep the original one.
Introduce a new API function sr_session_stopped_callback_set()
which can be used to receive notification when a session stops
running. This allows applications to integrate libsigrok event
processing with their own main loop, instead of blocking in
sr_session_run().
With this driver it is possible to set voltage target and current
limit. Also enabling and disabling the output is possible.
Analog output sends read back values from output. If output is
disabled analog outputs 0.00.
In protocol.c there is a g_usleep() call. This gives almost
every time enough time for PSU to parse and process input.
Multichannel devices aren't supported.
Instead of using a non-standard packed attribute, read the contents of the
probe EEPROM into a buffer and then process it using the R* macros.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Standard integer types may differ in size on different targets. Use fixed-size
types instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
SR_CONF_NUM_LOGIC_CHANNELS is defined as SR_T_INT32. Create the
GVariant with the correct type to avoid a type mismatch error in
sr_variant_type_check().
The resource API provides a generic means for accessing resources
that are bundled with sigrok, such as device firmware files. Since
the manner of resource bundling is platform-dependent, users of
libsigrok may override the functions used to open, close and read
a resource. The default implementation accesses resources as files
located in one of the XDG data directories or a directory defined
at compile time.
Use in-memory buffers instead of temporary files. This avoids
the need for low-level I/O on the FD returned by g_mkstemp().
Refactor the code accordingly. Also plug a number of leaks and
tighten the error checking.
Completely remove the old session save code that has been
superseded by the srzip output module. Also refactor a bit,
plug a number of leaks and tighten the error checking.
Introduce the sr_file_get_size() utility function to retrieve the
size of an open FILE stream. This is based on fseeko() followed by
ftello(), which are POSIX functions but quite portable in practice.
Since these calls operate on FILE streams instead of filenames, the
issue of filename encoding no longer arises.
Do not use Unix low-level I/O for reading a regular input file.
Read in the file header once and re-use the buffer for all input
modules participating in the scan. Also re-use a prefilled metadata
table instead of creating it anew for each input module tried.
This fixes parts of bug #423.
The list of fixed warnings:
src/output/srzip.c:285:3: warning: Value stored to 'ret' is never read
ret = zip_append(o, logic->data, logic->unitsize, logic->length);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
src/scpi/scpi.c:610:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/scpi/scpi.c:667:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/dmm/vc870.c:410:2: warning: Value stored to 'info_local' is never read
info_local = (struct vc870_info *)info;
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/conrad-digi-35-cpu/api.c:130:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/fx2lafw/api.c:658:2: warning: Value stored to 'timeout' is never read
timeout = fx2lafw_get_timeout(devc);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/protocol.c:941:3: warning: Value stored to 'retc' is never read
retc = SR_ERR_ARG;
^ ~~~~~~~~~~
src/hardware/gmc-mh-1x-2x/api.c:168:2: warning: Value stored to 'model' is never read
model = METRAHIT_NONE;
^ ~~~~~~~~~~~~~
src/hardware/ikalogic-scanalogic2/api.c:325:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/openbench-logic-sniffer/api.c:185:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/rigol-ds/api.c:813:3: warning: Value stored to 'devc' is never read
devc = sdi->priv;
^ ~~~~~~~~~
src/hardware/scpi-pps/api.c:405:2: warning: Value stored to 'ret' is never read
ret = SR_OK;
^ ~~~~~
src/hardware/yokogawa-dlm/api.c:239:2: warning: Value stored to 'ret' is never read
ret = SR_ERR_NA;
^ ~~~~~~~~~
Timer intervals shorter than about 100 ms are unnecessarily taxing
on system resources. Also, on systems like Windows the smallest
resolvable time unit without using high precision timers is about
15 ms. Regular timer intervals should be well above that value to
avoid being dominated by noise and round-off.
Firmware versions starting with 00.02.04 apparently cause the in and out
bulk endpoints to end up in a HALT state. This is likely related to the
larger transfer size quirk implemented in the Linux kernel for the Rigol
DS1000: this USBTMC implementation does not have that workaround.
Instead, if the firmware version is >= 00.02.04, both endpoints have the HALT
condition cleared on device close.
This fixes bug #354.
The wrong byte was being used to test for the nano indicator.
This resulted in reported resistance and capacitance readings being off
by orders of magnitude.
This fixes bug #657.
The check for p == q is basically checking whether p/q == 1. We should
be normalising the rational before it gets here though, so in this case
we should have p == q == 1 here.
scpi-pps at line 212 assumes that an SR_OK return means that the gvar
is valid, which leads to the following error:
** GLib:ERROR:/build/glib2.0-2.45.8/./glib/gvarianttypeinfo.c:184:g_variant_type_info_check: assertion failed: (0 <= index && index < 24)
GPIO direction should be set once right after exporting. There's no need
to reset it again - in fact it's a bug which causes the probe to be reset
every time the value is read/set and gives incorrect results when reading
the GPIO values with direction == 'in'.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Revision B of ACME hardware introduces probes with on-board at24cs02
EEPROM. Extend the ACME driver to support reading the contents of
the EEPROM via linux' sysfs interface.
Also: make the driver be able to tell the difference between revisions,
add new GPIO layout and set the shunt resistance for revB at probe
registration.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Only perform a single check at initialization time to see if the probe is
equipped with a power-switch. This is done in preparation for revision B
support which has this kind of information encoded in EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
After opening the USB device, set the device configuration to 1.
Actually, do it twice, just as the vendor driver seems to do. This
is supposed to trigger a lightweight reset of the device.
Originally, I omitted this reset sequence from the sigrok driver
because it simply did not work at all for me. However, it does seem
to work now, so that may have been a problem in libusb or the kernel
which is now fixed.
With some luck, this change may finally fix#327.
Use states SR_ST_ACTIVE and SR_ST_INACTIVE to indicate that the
device is open or closed, respectively. Do not use any of the
other state values. Improve the robustness of the open and close
methods in face of errors. Introduce a separate flag to indicate
that a running acquisition should be canceled.
Prepare the trigger masks at config_commit() time, so that the
trigger setup can be validated before starting an acquisition.
Accordingly, do actually report validation errors back to the
caller.
It turns out that g_stat() breaks apart when using 64 bit stat on
32-bit systems. Since the actual type of GStatBuf is decided when
glib/gstdio.h is included, it is thus possible for GLib itself to
be compiled with a different type than user code.
Ouch. Unfortunately going back to plain stat() also means that we
lose Unicode filename support on Windows.
Since Autoconf places some important feature flags only into the
configuration header, it is necessary to include it globally to
guarantee a consistent build.
Disallow polling for input/error and output-ready events at the
same time, and ensure only a single FD event source is installed.
Also, do not leak if the FD event source is removed by means
other than calling serial_source_remove().
On MinGW, two implementations of printf() are available: either
the Microsoft native one or a standard-conforming replacement from
gnulib. Since we build in C99 mode, headers such as <inttypes.h>
already select the standard-conforming variant. However, MinGW's
GCC does not seem to know about this and assumes MS-style format
syntax by default, which triggers a lot of wrong warnings.
Thus, on MinGW, explicitly decorate sr_log() with the gnu_printf
format flavor attribute. Also use GLib's printf replacements in
the logging implementation to make sure we link to a conforming
printf on any platform, independently of the compiler flags.
This gets rid of the mistaken -Wformat warnings for sr_log(), but
does not cover functions such as g_strdup_printf() which do not
explicitly specify the gnu_printf flavor in the format attribute.
This can be overcome by adding "-D__printf__=__gnu_printf__" to
CPPFLAGS, but it would be inappropriate for libsigrok to define
this on its own.
The confusingly named sr_log_logdomain_set() simply set a global
string prefixed to the log message by the default log callback.
This is pretty much useless, misleadingly named, and not used by
either sigrok-cli or PulseView.
A few of these were pretty serious, like missing arguments,
passing integers where a string was expected, and so on.
In some places, change the types used by the code rather than
just the format strings.
SR_LOG_DBG and above are targeted at developers, so it makes sense
to extend timestamp output to that. Also sanitize the calculation
of the timestamp components a bit.
Get rid of the specicialized sr_err(), sr_warn(), etc. functions.
Instead, define the logging helper macros in terms of sr_log(),
and remove the sr_log() helper macro so that no function is hidden
by a macro anymore.
Decorate sr_log() with G_GNUC_PRINTF to detect varargs errors. This
unearthed a gazillion warnings all over the place which will have
to be fixed.
Also convert the helper macros to ISO C99 __VA_ARGS__ style instead
of relying on a GNU C extension. Paste the log prefix directly into
the format string to make this work.
Some drivers, such as zeroplus-logic-cube, run everything they do
right away in dev_acquisition_start(), never installing any event
sources. Handle that evilness by returning from sr_session_run()
immediately if there are no sources.
Replace the custom session main loop with the GLib main loop.
This is phase one of the port, which leaves the session and
driver APIs unchanged while replacing the internals.
The Hung-Chang DSO-2100 is a parallel port PC oscilloscope sold back
in 1999 under brand names like Protek and Voltcraft.
This inital version of the driver has the following limitations:
- Hardcoded calibration values. All parameters are set to 50%.
- No support for auto triggering
- No support for TV sync trigger modes
- No support for the "scroll acquisition" mode
In scroll acquisition mode the device behaves more like a multimeter
and reports the current voltage of a probe on request. While in this
mode the sample rate is limited by the parallel port interface, it is
the only way to capture both channels at the same time (well, sort of).
Calibration would need auto triggering. The calibration values are very
temperature dependent and the device takes literally hours to reach its
final temperature. Every vdiv setting needs its own set of calibration
values. Without hardware modifications, the calibration settings wear
of in less than a second while waiting for a trigger because the
capacitors storing those values are not recharged in state 0x21.
Wolfram Sang
Daniel Elstner
Uwe Hermann
Martin Ling
Soeren Apel
Stefan Brüns
Tilman Sauerbeck
Hannu Vuolasaho
Petteri Aimonen
Matthieu Gaillet
jry
Bert Vermeulen
Aurelien Jacobs
Karl Palsson
Bartosz Golaszewski
Martin Lederhilger
Scott Allen
Daniel Glöckner