Also don't load the footprints up front. The whole purpose of the
footprint-info stuff is to have enough info about the footprints to
filter them *without* loading. After that just load individual
footprints as we need them.
Fixes https://gitlab.com/kicad/code/kicad/issues/6177
wxTextFile uses wxFile which uses write syscalls which means its unbuffered.
This makes file IO more expensive against network shares where it will flush far too aggressively.
wxTextFile is fine for reads however.
- pcbnew should use status bar on success like eeschema
- Add a helper to clear msgpanel and set it in one go to avoid redraw delays due to doing processing in between
- remove outdated code or comment coming from old drawing code using wxDC
- move zoom values lists to zoom_defines.h
- fix incorrect zoom max and min values (gal scaling factor limits).
We had some spurious bugs where both ends would get dragged to a
single point (making them disappear). While I never caught it
in the debugger, I'm guessing that the flags weren't getting
cleared properly or were getting overwritten or something. Anyway,
it now uses std::pair instead.
Fixes https://gitlab.com/kicad/code/kicad/issues/6550
Fixes https://gitlab.com/kicad/code/kicad/issues/6431
1) make sure we get the default netclass when we want it
2) escape for HTML (particularly important for "<invalid>", but also
for reporting user rule names, netclass names, etc.)
1) Separate out CONSTRAINT types
2) Filter both source and dest pads/vias for drilled holes when doing
hole-to-hole checks. We were checking the items being put into the
DRC RTree, but not the items we were scanning.
3) Add hole clearance to Board Setup Constraints panel.
Fixes https://gitlab.com/kicad/code/kicad/issues/6546
Fixes https://gitlab.com/kicad/code/kicad/issues/4683
So the new steals-focus protection stuff works well when there's a
focused control, but not as well when there's a modal dialog up which
happens not to have a focused control (or worse, a focusable control).
This adds a second mechanism for also checking to see if a modal dialog
is up (something that wxWidgets, true to form, makes very difficult).
Fixes https://gitlab.com/kicad/code/kicad/issues/6520
Rotate text using the Rotate90() function which gets the orientation
right.
Also, when calculating the center point for rotation, don't include
labels if the selection contains other stuff. It just makes the
rotation odd, and tends to cause walking when continuing to rotate
(due to keep-upright being non-symmetrical).
Fixes https://gitlab.com/kicad/code/kicad/issues/git
Copy to clipboard save items (using S expr description) using wide strings
(not UTF8 encoding).
But Paste from clipboard was not converting the wide string to UTF8 string
when getting the stored data to send it as std::string to the S expr reader.
Fixes#6449https://gitlab.com/kicad/code/kicad/issues/6449
It shows much more detail. Removes some nag dialogs and places
hypertext links in others.
Also fixes the auto-layer-showing to correctly show Edge.Cuts or
F.CrtYd or B.CrtYd for errors relating to them.
Fixes https://gitlab.com/kicad/code/kicad/issues/6446
1) Generalize SCH_ITEM owners (SCH_COMPONENT, SCH_SHEET, and now
SCH_GLOBALLABEL)
2) Generalize hypertext items
3) Use SCH_FIELD autoplace infrastructure for placing intersheet
references
4) Use textVar infrastructure for buildin intersheet references.
As an important side-effect this also fixes the undo issues with
intersheet refs.
On non-Unix, the platform selection is in platform.h, not on the command
line using the preprocessor macros from wx-config.
<wx/setup.h> relies on the platform being selected correctly, if it is
included directly, it cannot determine the correct configuration with
Visual Studio.
wxWidgets 3.1.5+ on Linux will compile with the Wayland EGL
canvas as the backend instead of the X11 backend. This requires a
version of GLEW compiled with the proper EGL defines and a different
header/code for certain parts that are X11 GLEW specific.
This introduces an in-tree version of GLEW that will be built with the
GLEW_EGL flag then statically linked into the KiCad executables when
EGL support is needed.
It was causing problems with surprising behaviour and issues with
allowing spaces in existing labels. We'll work on something better
for 7.0....
Fixes https://gitlab.com/kicad/code/kicad/issues/6073
1) Make sure that layer dependencies don't prevent us from drawing
drill marks.
2) Don't draw pad shapes when their particular layer isn't enabled
(a side effect from the above)
3) Allow the printout painter to set a different hole colour (the
special case for through-hole pads was handled twice anyway -- once
in LoadColors() and once in draw( D_PAD ).
4) Replace the call to getDrillSize() which handles swapping in the
small mark size if set.
Fixes https://gitlab.com/kicad/code/kicad/issues/4847
The groundwork has now been laid for per sheet instance data. Initially
this only supports sheet page numbers but could be expanded to include
other per sheet instance information.
ADDED: Support for user defined schematic page numbers.
Setting a line thickness = 0 for graphic objects (circle, rect, line) is
allowed but creates issues for circles that were plotted a non filled shapes
but having a outline thickness = 0.
Two main changes: netclass values need to go through the DRC engine
so they can interact with other rules. They're also now dependent
on the layer being routed as well as the start object.
Also make the controls adjust to each other better. For instance,
copy-track-width needs to turn off when you select a particular
track width, and a particular track width needs to zero out when
you choose copy-track-width.
Fixes https://gitlab.com/kicad/code/kicad/issues/5951
This will always show 1 unit from each system, with the primary unit
being the current frame unit and the secondary unit being the
most recent unit used from the other system. These are saved in
the settings, so they are saved between runs.
* Make the ruler able to switch to mils after creation
* Cleanup an unused flag in Pcbnew dimensions
* Move unit changed notification into EDA_DRAW_FRAME so more
frames to use it.
* Allow switching units when GerbView ruler tool is active
Switch Eeschema to use the built-in printing routines
because its precisions are close to those and it is
cleaner.
Give mils a precision of 2 decimal places to match
the precision shown in inches.
This uncovered a memory corruption bug in MODULE's move operator,
several bugs in MODULE's move and copy constructors, and a bug in
BOARD's GetItem() call.
It also bumps the file format for saving/restoring groups inside
footprints.
Using CopyFile() that can collide with a windows header create hard to
understand errors, including link errors.
Renaming this function avoids these strange errors.
Previously, init order depended on the ordering of the
tool state map, which is opaque from the point of view of
registration. This makes it challenging to make one tool's
init depend on another. With this change, registration
order defines init order.
They're only on screen when they're being used, and we don't have
a GAL available to calculate their actual extents from (since their
text scales with zoom).
Fixes https://gitlab.com/kicad/code/kicad/issues/5845
in most of files, including wx.h is not necessary, when only 2 or 3 wx files must be included.
Moreover, on windows, including wx.h sometimes create compil warnings about
shadowed vars defined in some specific windows headers.
When invoking "Break Track" from the RMB context menu, Pcbnew
gets and uses the current position of the mouse to figure out where to
break the track. The problem is that the mouse has to be moved to select
the "Break Track" menu item, and the mouse position used is wrong. This
can result in the break in the wrong location or not happening at all.
CHANGED: This commit determines if the "Break Track" was invoked from a
context menu or a hotkey. If a hotkey, it uses the current mosue position.
If a context menu, it uses the original postion of the mouse when the menu
was opened.
plotter.h contains now only a header common to all plotters.
The code does not actually change, but it allows modifying a specific plotter
without recompiling most of kicad files.
Also simplifies groups so that other areas of code that have to know
about them at least don't have to know as much. One of the simplifications
is to not worry so much about empty groups until save time; others are in
the access logic to parent groups.
Also simplifies user model slightly by removing Merge and Flatten
(which are just ungroup/group and ungroup/ungroup/.../group).
Also allows multiple groups to have the same name. This is useful when
using groups for a classification system.
Fixes https://gitlab.com/kicad/code/kicad/issues/5788
CHANGED: GetDocumentExtents() in 'eda_draw_frame.h' now has a bool
parameter "aIncludeAllVisible" with a default value "true" which makes
it behave as it did before adding parameter. If "aIncludeAllVisible"
is false, the returned bbox ignores some items depending on which
program it is running in.
CHANGED: Made "Zoom to Objects" use only PCB edge in Pcbnew. This
allows text, notes, etc outside the PCB edge to be excluded in the
zoom calculation.
CHANGED: Added "Zoom to Objects" to Pcbnew main menu, and to RMB context
menus for Eeschema and Pcbnew.
Fixes https://gitlab.com/kicad/code/kicad/issues/5787
The infobar changes the size of the visible screen, so adding/removing
it will shift the screen center, causing the position of onscreen
objects to move up/down. This changes the sizing to pin the bottom
corner position when showing/hiding the infobar
Fixes https://gitlab.com/kicad/code/kicad/issues/5776
ADDED memberOf() function for DRC rule expressions.
Also fixes a bug in several of the pickers where the event wasn't
being correctly passed.
Fixes https://gitlab.com/kicad/code/kicad/issues/5647
This changes the file format. All previous copper layers that had a user
defined name are forced back to the canonical name and the user defined
name is stored as an optional quoted string in the layer definition and
only used for UI and plotting purposes. All copper object layer names
are now the canonical name for internal file use.
ADDED: Nine new user definable non-copper layers that can be optionally
added to the board layer stack.
CHANGED: All board layers can now be renamed by the user.
CHANGED: User defined layer names can now contain space characters.
Fixes https://gitlab.com/kicad/code/kicad/issues/1969
ViewGetLOD() returns the minimal value of a zoom to show an item.
However a zoom is a double, and using int as minimal value does not
allows setting a correct value in some cases.
These settings objects could be created in a constructor/destructor
so we should catch the exception since those are noexcept.
Also change the settings trace to match the other kicad traces
as KICAD_SETTINGS
Also improves the SNR and consistency of the menu item text. For
instance, a position is rarely useful, while relative sizes can be.
Also removes some unnecessary repitition, such as "Graphic Rectangle"
when "Rectangle" communicates the necessary information.
Also fixes a bunch of naming issues, primarily with lowercase for
protected variables, but also some for consistency with other parts
of the code.
Also changes the zone fill radio buttons in Board Setup to be more
generic referring to legacy vs. current, and to have tooltips.
Fixes https://gitlab.com/kicad/code/kicad/issues/5583
CHANGED: The margin used in 'Zoom to Fit' is now 2% instead of 10%.
ADDED: Added 'Zoom to Objects' to Eeschema which does not include
the page and border in the bbox calculations.
CHANGED: Removed pre-existing code that tweaked the center to account
for the scrollbars. It actually made the view off center. Removing it
results in perfectly centered zooms.
Fixes https://gitlab.com/kicad/code/kicad/issues/5145
This is a board file format change to account for the new properties.
Also, we now only store the critical information about the dimension's
geometry in the board, rather than storing every drawn line.
The DIMENSION object is now an abstract base, and ALIGNED_DIMENSION
is the implementation that exists today (we will add more dimension
types in the future)
You can now enable and disable snap to grid when drawing/editing across
all apps. You can also tie snap to grid to the visibility of the grid
to allow rapid enable/disable via grid display.
There was a regression in v6 where the zoom to selection toolbar
item wasn't canceling the tool when pressed and the tool was active
(it was in v5). This implements a more generic framework for canceling
tools on button presses.
Fixes https://gitlab.com/kicad/code/kicad/issues/5103
Also moves to WX_GRID to get rid of some wxGrid bugs, and moves the
provision of attrs to the GRID_TABLE (as those applied to the grid
are ignored when a table is specified).
Fixes https://gitlab.com/kicad/code/kicad/issues/5260
For instance, we get things like high-contrast-mode from the pad
dialog when rendering a pad preview, but we want the colours from the
parent PCB_BASE_FRAME.
windowClosing() calls Destroy() when the wxCloseEvent has no veto.
This is fine for usual EDA_BASE_FRAME frames, but not for frames shown in modal mode.
In modal mode, windowClosing() should not call Destroy(), because the calling frame
expects the instance not deleted after closing.
(the caller has to call Destroy() only once the frame can be actually deleted)
The center point on polygons now maintains the axis of the dragged line
and, optionally with Ctrl pressed, maintains the slope of the adjacent
segments as well.
This also fixes a longstanding issue that prevented the ctrl-snapping
from using the original point rather than the last updated point when
constraining.
Fixes https://gitlab.com/kicad/code/kicad/issues/2465
This commit adds support for display origin transforms to the PCB_BASE_FRAME
class. This instantiates a PCB_ORIGIN_TRANSFORMS object, and overrides the
GetOriginTransforms method in the EDA_DRAW_FRAME class to reference it.
The formatting of the status line has been updated to display coordinates
relative to the user-selected origin, and with the coordinates increasing
in the user-selected direction.
This commit adds the user configuration options to support display
origin transforms to the PCB_DISPLAY_OPTIONS class. This data is
configured by the "Origins & Axes" preferences panel added in a
later commit.
This commit modifies the UNIT_BINDER class to invoke the ORIGIN_TRANSFORMS
methods to support Display Origin Transforms.
The EDA_DRAW_FRAME class is modified to instantiate an ORIGIN_TRANSFORMS
object providing null transforms. A function is provided to allow the
UNIT_BINDER to find the ORIGIN_TRANSFORMS object in an overrideable manner.
This commit adds the ORIGIN_TRANSFORMS class to support Display Origin
Transforms in all KiCad applications.
Functions are provided to perform four basic types of origin coordinate
transforms:
* Transform a relative coordinate from internal to display form
* Transform a relative coordinate from display to internal form
* Transform an absolute coordinate from internal to display form
* Transform an absolute coordinate from display to internal form
These functions are supported for data types "int", "long long int",
and "double". The default implementations for all but "int" simply
return their input unchanged; the implementation for "int" invokes
the implementation for "long long int".
The expectation is that the different KiCad applications will create
derived classes from this base class and override the functions as
needed. Protected template functions are provided for the standard
translations to maintain consistency within the derived classes.
Display warning infobar in the board/schematic setup when no project
is loaded, since most of the settings in those dialogs are saved in
the project and not in the board/schematic file.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/4868
Short net names are not unique; full names with paths must be used.
Added a grid cell renderer that does the escaping, to make it easier
to display net names in grid cells.
Once you unescape a net name, you can't go back to the escaped form
because you can't assume which `/` should be {slash} and which `/`
Because of this, we cannot use Unescape/Escape on the data model in
the netclass setup panel, and instead do the Unescape in the view.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/5331
This time remove the push/pop from the picker tools as that's
responsible for the issue of trying to re-activate the move action
when its popped. Instead do the push/pop from the client code
of other actions that need it, and not at all from the move-with-
reference action.
Fixes https://gitlab.com/kicad/code/kicad/issues/5336
* Make the app progress indicator only have the indeterminate state
when the taskbar indicator is used (causes an uused variable warning
on wx<3.1)
* Remove unused dry run variable in pcb_netlist.h
* Remove unused forceDropAnnotations from the paste special dialog
since the dialog only controls keeping them.
wxScrolledCanvas is not properly exported, so when we
add a wxGrid it has a chance of creating linker errors.
Including the wx/grid.h ensures that the linker does not
see two conflicting symbols between gal and the other
place where wxGrid is used.
ADDED: Allow DXF/SVG graphics to be imported as a group
Also, cleanup the placement routine to allow the edit tool's flip
and rotate routines to be used when placing the items.
The use of printf, wxLogDebug, and std::err/std::out causes excessive
debugging output which makes finding specific debugging messages more
difficult than it needs to be.
There is still some debugging output in test code that really needs to
be moved into a unit test.
Add debugging output section to the coding policy regarding debugging
output.
Flags != language See http://www.flagsarenotlanguages.com We now use
local, untranslated language names for all languages.
Languages that have not been updated in >5 years and have less than 15%
of available strings translated have been removed from the menu options.
If a translator steps up to update the .po files, we can re-add them
This leaves the decision to check/enable menu items to the main UI
conditions, and only the menu has control over showing/hiding the menu
items. Also rip out a special case for the preferenes item that isn't
needed on OSX anymore since all the main menus have been moved to
ACTION_MENUs now.
* Frames moved: cvpcb, cvpcb footprints frame, gerbview, pagelayout editor
This also introduces new EDITOR_CONDITIONS that are used to set the
conditions of very common editor settings.
Also, some IDs were converted to tools in the pagelayout editor.
This allows for the tool framework to keep track of a universal
set of conditions for the UI state (enabled/checked/shown) for
controls of actions. It removes the need for the main menubar
menus to be CONDITIONAL_MENUs and be rebuilt on each open,
and instead makes the updates of the check and enabling of
items handled in the native wxWidgets way.
This commit switchs the 3d viewer and kicad project manager window
over to this system.
This introduces layer handling to a lot of the geometry routines.
Many of them don't do much with it now, but it does help multi-layer
zones and will help when padstacks are implemented.
The variables in the common settings struct are only updated on
save, so Python must use the ones from Pgm to get its values.
This does lead to the observation that Python's changes to the
variables do affect KiCad (they can break resolvers). So apparently
it can mess with us but we can't mess with it easily.
Also, improve the environment variable tracing infrastructure to capture
more changes.
The base GAL has the linewidth property already, and its
accessor will only return the base version. This was causing
problems with the Cairo printing GAL, since that setter wasn't
using the base class version. Also, this removes the print-specific
setter, since the actual setting of line width shouldn't be done
there and is instead done where the drawing happens.
Fixes https://gitlab.com/kicad/code/kicad/issues/5089
This ensures the colors used by the status text pane in the preview
widget are the same as the canvas, so there is a seemless transition
between the two.
Additionally, remove the scrollbars from the symbol preview widget
in the place symbol dialog - they are pointless.
Before this, the environment variables inside Python wouldn't reflect
the updates to them made after the interpreter was started in Pcbnew.
This will call into Python and set the variables when they are changed,
since Python can't synchronize itself when running in an embedded
interpreter.
Fixes https://gitlab.com/kicad/code/kicad/issues/5071
ADDED: Progress indicator in the taskbar
This adds a progress indicator to the Windows and macOS taskbar
icons to display the progress of some operations.
Note, this requires wxWidgets 3.1+
KiCad stores 3D cache files but never gets rid of any of them.
This patch adds a new function called 'CleanCacheDir()'. Any cache
files older than the passed 'number of days' parameter are deleted.
Fixes https://gitlab.com/kicad/code/kicad/-/issues/1928
Store list of previously open projects only in kicad.json
Keep all management of open projects in SETTINGS_MANAGER
Also add kicadSettings() for convenience
On platforms with limited framebuffer attachments, like GC7000L
driven by the open source etnaviv driver, we can still use
GPU acceleration by drawing directly to the main buffer.
EDA_DRAW_PANEL_GAL::onPaint checks if an overlay target is
available in the GAL, and if not, redraws the whole view if the
overlay target should be dirty.
Clearing of the overlay target is a no-op if there is no overlay
buffer.
Signed-off-by: Lukas F. Hartmann <lukas@mntre.com>
The fix convert all std::string storing a path to wxString (unicode support)
wxString were already used at many place to store paths, but not all.
For internal calculations mixing char strings and wide char strings is a recipe
for bug: any missing conversion between UTF8 and wxString breaks paths.
By default KiCad will now print each polygon point on its own line.
This adds to the vertical distance for large polygons but makes revision
control much cleaner as single point addition to a polygon does not
propagate to a diff over the full polygon.
Users/developers who want to save the files using the 4-points per line
have the ADVANCED_CONFIG setting 'CompactSave' which will provide the
original save method
This way, when the user changes their color theme, any sheets
that did not have a specific color set will change with the theme.
Also add a button to clear color overrides from a sheet, because
any schematics that have been saved before this change will have
the colors set to something other than UNSPECIFIED.
This API doesn't transfer ownership, so no smart pointers are required --
this just needlessly tightens requirements on the user of the interface.
(Fixes five instances of MSVC C26410 warning)
This is particularly important to keep the user from having to
enter overly verbose statements such as:
A.Type == 'via' && A.Via_Type == 'buried'
when:
A.Via_Type == 'buried'
is perfectly clear.
- convert expression string tokens to single-quote-delimited
- fix bug where netclass assignments weren't getting updated after
board setup dialog
- move property manager rebuild to lazy evaluation
- improve performance with wider use of const&
- retire DRC_SELECTOR stuff
- use wxString for GUI stuff (particularly translated stuff)
- fix EqualTo() to return false instead of asserting when op types
don't match
- fix buffer overruns with fixed-size string buffers
- make expression function calls case-insensitive
- integrate expression errors into rule parser
- produce more and better error messages
- keep BOARD_ITEM ptrs const as long as possible
- fix a couple of uninitialized variables
Jeff Young
Wayne Stambaugh
lê văn lập
Marek Roszko
Jon Evans
jean-pierre charras
Ian McInerney
qu1ck
Werni
Simon Richter
Oleg Endo
Seth Hillbrand
Mikolaj Wielgus
Thomas Pointhuber
Michael Kavanagh
Tomasz Wlostowski
Franck Jullien
PJM
Mario Luzeiro
Roberto Fernandez Bautista
Fabien Corona
Reece R. Pollack
Qbort
Joshua Redstone
bjpiccioni
Peter Montgomery
mntmn