The code earlier was in a single .h file, so it's now separated into a C file
and H file
Signed-off-by: Kumar Abhishek <abhishek@theembeddedkitchen.net>
If a channel in the higher-than-8-bit group is enabled then use
16-bit captures. Otherwise just do 8-bit captures.
Signed-off-by: Kumar Abhishek <abhishek@theembeddedkitchen.net>
Starting with Linux kernel version 4.9, BeagleLogic attributes
setting does not require root permissions.
Signed-off-by: Kumar Abhishek <abhishek@theembeddedkitchen.net>
This is unlike the previous behavior to return 8 channels and then
use logic_channels to get all the 14 channels
Signed-off-by: Kumar Abhishek <abhishek@theembeddedkitchen.net>
Values like '-0.1' would be parsed as being positive, as the integral
type does not discern +0 and -0. Also allow values without leading
integral value, to match behaviour of strtod/sr_atof.
This was leading to an invalid threshold config value and indirectly
to frontend issues.
Slightly modified patch from James Churchill <pelrun@gmail.com>, thanks!
The previous implementation unconditionally submitted analog data
whenever values could get extracted out of received serial packets.
This commit checks the channels' enabled state before submission. Care
is taken to obey the user's acquisition limits, exclusively counting
submitted not received values.
Upon reception of serial data from the ES51919 LCR chipset, the data for
channels P1 and P2 was extracted from the packet, and unconditionally got
sent to the sigrok session.
Do check the channels' enabled state before submission. This fixes for
serial-lcr what recently got reported for a Brymen DMM. Tested with
$ sigrok-cli -d peaktech-2170:conn=/dev/ttyUSB0 --channels P2
and other --channels specifications.
The es51919_serial_clean() routine is called by std_dev_clear_with_callback().
Common code unconditionally frees the 'priv' part. The cleanup callback only
shall release descending resources which are local to the callee and opaque
to the caller.
This fixes a double free error. Tested with PeakTech 2170.
$ sigrok-cli -d peaktech-2170:conn=/dev/ttyUSB0 --show
When the acquisition was stopped before a configured limit was reached,
no sample data was retrieved. This is because the api.c stop routine did
unregister the receive callback.
Pass the stop request to the receive routine instead when stop is called
while the acquisition is still running. Have sample data downloaded very
much like it's done for reached limits, and existing logic will run the
stop routine again after state was advanced to "idle".
Extend the 'state' tracking while we are here, mark sample download as
well (that was omitted in the previous implementation). Though the
omission was non-fatal. Move the release of 'dram_line' to some earlier
location (as soon as the resource is not needed any longer), before some
rather complex calls to other routines will execute.
Reported-By: Michael Kaplan <M.KAPLAN@evva.com>
Move the check for the capture ratio being 0..100 into the wrappers,
drop unneeded helper functions, fix incorrect variable types, minor
other consistency fixes.
This makes the code more consistent with the rest of the code-base
and also allows std_gvar_min_max_step_array() to work here.
Without this change:
src/hardware/scpi-pps/api.c: In function ‘config_list’:
src/hardware/scpi-pps/api.c:570:40: warning: passing argument 1 of ‘std_gvar_min_max_step_array’ from incompatible pointer type [-Wincompatible-pointer-types]
*data = std_gvar_min_max_step_array(ch_spec->voltage);
^~~~~~~
In file included from src/scpi.h:30:0,
from src/hardware/scpi-pps/api.c:23:
src/libsigrok-internal.h:964:19: note: expected ‘const double *’ but argument is of type ‘const float *’
SR_PRIV GVariant *std_gvar_min_max_step_array(const double a[3]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/scpi-pps/api.c:573:40: warning: passing argument 1 of ‘std_gvar_min_max_step_array’ from incompatible pointer type [-Wincompatible-pointer-types]
*data = std_gvar_min_max_step_array(ch_spec->frequency);
^~~~~~~
In file included from src/scpi.h:30:0,
from src/hardware/scpi-pps/api.c:23:
src/libsigrok-internal.h:964:19: note: expected ‘const double *’ but argument is of type ‘const float *’
SR_PRIV GVariant *std_gvar_min_max_step_array(const double a[3]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
src/hardware/scpi-pps/api.c:576:40: warning: passing argument 1 of ‘std_gvar_min_max_step_array’ from incompatible pointer type [-Wincompatible-pointer-types]
*data = std_gvar_min_max_step_array(ch_spec->current);
^~~~~~~
In file included from src/scpi.h:30:0,
from src/hardware/scpi-pps/api.c:23:
src/libsigrok-internal.h:964:19: note: expected ‘const double *’ but argument is of type ‘const float *’
SR_PRIV GVariant *std_gvar_min_max_step_array(const double a[3]);
^~~~~~~~~~~~~~~~~~~~~~~~~~~
This ensures consistent handling of the SR_CONF_SCAN_OPTIONS and
SR_CONF_DEVICE_OPTIONS (with sdi NULL or non-NULL) config keys
and also reduces copy-pasted boilerplate in the drivers a bit.
This function does not handle channel-group specific items, that's
very driver-specific and thus left to the individual drivers.
Also move some generic checks and error messages from the drivers into
the sr_config_list() wrapper.
The HW simply stops sending data on overflows, so if we receive no data
in one second, we abort the acquisition. We also need to allocate more
buffers to support higher sample rates.
Until now, clear_helper() callbacks for std_dev_clear_with_callback()
were expected to g_free(devc), but not all of them did that.
Have std_dev_clear_with_callback() unconditionally g_free(sdi->priv)
(i.e., devc), regardless of whether a clear_helper() callback was
provided or not. It was doing g_free(sdi->priv) when no callback
was provided already anyway.
This makes the individual drivers' clear_helper() implementations
shorter and prevents errors such as missing g_free(devc) calls.
This works, because all drivers either call std_dev_clear_with_callback()
directly, or indirectly via std_dev_clear().
This also allows us to remove some no-longer needed dev_clear()
and clear_helper() implementations that only did g_free(devc)
in favor of std_dev_clear().
Be explicit and consistent in the drivers about which dev_clear function
will be called to avoid confusion and inconsistencies.
Drop some open-coded implementations of std_dev_clear().
Drop unneeded log messages, add some others that might be useful,
document which ones we're intentionally not emitting.
Don't log "$operation successful" type of messages in most cases,
that's too verbose; logging failures only is sufficient there.
baylibre-acme: Don't log "No such file or directory" messages during scan,
this triggers on all kinds of unrelated devices (e.g. "AMDGPU i2c bit
bus 0x91" in this case):
sr: [...] baylibre-acme: Name for probe 1 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0040/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 2 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0041/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 3 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0044/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 4 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0045/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 5 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0042/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 5 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-004c/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 6 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0043/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 6 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0049/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 7 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0046/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 7 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-004f/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 8 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-0047/name”: No such file or directory
sr: [...] baylibre-acme: Name for probe 8 can't be read: Failed to open file “/sys/class/i2c-adapter/i2c-1/1-004b/name”: No such file or directory
- sr_dev_clear(): Don't try to clear uninitialized drivers (the same
check was previously done in std_dev_clear()).
- Document some places where we intentionally don't emit log messages.
- std: Various Doxygen fixes and updates.
- std: Add some more sanity-checks on input parameters.
src/hardware/saleae-logic-pro/protocol.c:389:12: warning: 'set_led' defined but not used [-Wunused-function]
static int set_led(const struct sr_dev_inst *sdi, uint8_t r, uint8_t g, uint8_t b)
^
CC src/hardware/saleae-logic-pro/api.lo
src/hardware/saleae-logic-pro/api.c: In function 'dev_acquisition_handle':
src/hardware/saleae-logic-pro/api.c:332:9: warning: missing initializer for field 'tv_sec' of 'struct timeval' [-Wmissing-field-initializers]
struct timeval tv = {};
^
In file included from /usr/include/x86_64-linux-gnu/sys/time.h:27:0,
from include/libsigrok/libsigrok.h:24,
from src/hardware/saleae-logic-pro/protocol.h:25,
from src/hardware/saleae-logic-pro/api.c:23:
/usr/include/x86_64-linux-gnu/bits/time.h:32:14: note: 'tv_sec' declared here
__time_t tv_sec; /* Seconds. */
^
The asix-sigma driver was reported to fail in combination with newer
libftdi versions, because the firmware upload routine opened again an
already opened device, and then failed to claim the interface. Which was
not fatal before with previous libftdi versions.
Remove the redundant open call. Remove the local FTDI context variable,
which brings the firmware upload routine in line with all other calls
that communicate to the USB device.
This fixes bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
The asix-sigma driver supports different samplerates, which will involve
different firmware images and will affect the number of available logic
channels as well as their memory layout in downloaded sample data.
Make sure to only store the configuration's parameters after the setup
of that configuration has successfully completed, and make sure to store
a consistent set of parameters. Specifically don't change the number of
channels when the firmware upload failed.
This fixes part of bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
The firmware upload code paths in the asix-sigma driver used to return
either the SR_OK code, or the magic number 0 for error conditions. Which
happens to be identical and cannot be told apart by callers.
Provide proper SR_ERR return codes for error conditions, such that
callers can tell whether the firmware upload succeeded.
This fixes part of bug #471.
Suggested-By: Marian Cingel <cingel.marian@gmail.com>
Adjust the string to boolean conversion for an edge case. Accept empty
text (either NULL or empty strings) to mean true instead of false.
This behaviour is more useful from the user's point of view, when the
option's name alone will enable a feature, and an explicit "option=yes"
specification is not strictly necessary. All calling applications in
mainline already implemented this semantics.
../src/hardware/hung-chang-dso-2100/api.c: In function ‘config_commit’:
../src/hardware/hung-chang-dso-2100/api.c:562:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
state = 0x01;
~~~~~~^~~~~~
../src/hardware/hung-chang-dso-2100/api.c:563:2: note: here
default:
^~~~~~~
../src/hardware/hung-chang-dso-2100/api.c:565:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret != SR_OK)
^
../src/hardware/hung-chang-dso-2100/api.c:567:2: note: here
case 0x01:
^~~~
../src/output/csv.c: In function ‘receive’:
../src/output/csv.c:580:8: warning: this statement may fall through [-Wimplicit-fallthrough=]
*out = g_string_new(ctx->frame);
~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~
../src/output/csv.c:582:2: note: here
case SR_DF_END:
^~~~
../src/input/wav.c: In function ‘send_chunk’:
../src/input/wav.c:200:2: warning: ‘memset’ used with length equal to number of elements without multiplication by element size [-Wmemset-elt-size]
memset(fdata, 0, CHUNK_SIZE);
^~~~~~
../src/input/raw_analog.c: In function ‘init’:
../src/input/raw_analog.c:133:31: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size 6 [-Wformat-truncation=]
snprintf(channelname, 8, "CH%d", i + 1);
^~
../src/input/raw_analog.c:133:28: note: directive argument in the range [1, 2147483647]
snprintf(channelname, 8, "CH%d", i + 1);
^~~~~~
../src/input/raw_analog.c:133:3: note: ‘snprintf’ output between 4 and 13 bytes into a destination of size 8
snprintf(channelname, 8, "CH%d", i + 1);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The previous implementation used to provide datafeed packets which
contain logic data in positions that correspond to disabled channels.
Do mask out logic data of disabled channels in the memory image before
it is sent to the session's datafeed. This implementation works fine for
those situations where either all logic channels are enabled (default
configuration) or when only the upper channels get disabled (which can
be considered a typical use case).
For those configurations where enabled channels follow disabled channels
(i.e. setups with gaps in the sequence of enabled channels) behaviour
will be unexpected: Neither is the mask adjusted to contain gaps, nor
will enabled channels get mapped to result in a dense representation.
The respective code paths are marked with TODO comments.
Add a comment to discuss a non-obvious generator call for analog data in
the acquisition start routine, while we are here.
The generator logic determines how many samples per group (analog and
logic) need to get produced, then keeps iterating until each group has
reached the specified count. Different groups can generate different
numbers of samples per iteration, they have their own stride.
It's essential to check whether all channels in a group are disabled, to
then completely skip the respective half of the generation loop. Without
this check, the group would be expected to generate data but it won't,
which results in an endless loop. This was observed with analog channels.
There was another issue with logic channels. Unexpected logic data was
seen in the output although neither logic channel was selected.
This commit fixes bug #923.
Skip the emission of session datafeed packets for disabled analog
channels.
Implementation detail: Allow for quick lookup of the channel that is
associated with an analog generator, as the data generation routines
only pass generator references in later calls.
This fixes part of bug #923 (which initially is about unexpected
logic data while analog channels were affected in similar ways).
After the requested number of samples was sent, another session df
packet was emitted with one sample for the analog channels, which
contained the most recent result of averaging. Make this emission
depend on the "averaging requested?" flag.
This fixes bug #930.
The 'demo' driver supports scan options to adjust the number of
supported channels, and runtime control for the enabled state of
channels.
Starting with zero analog channels created (scan option) resulted in a
runtime assertion. Creating but disabling analog channels (GUI checkbox,
CLI option) resulted in unexpected output for disabled channels.
Move the creation of a hash table out of the conditional loop that
iterates over created analog channels. Which results in the table's
always being valid, and iteration during data acquisition yields no
analog output as is expected.
This fixes bug #625.
A previous implementation of the demo driver supported the creation of
larger channel counts yet only enabling part of them by default. This
was kind of pointless, I just was not aware of the available scan
options.
Drop the "enabled channels" limitation, enable all channels that get
created (like the implementation before the experiment did), and create
as many channels as was compiled in by default or later got specified
by scan options.
Before firmware upload some models (e.g. the original DSLogic or the
DSLogic Pro) don't have any USB manufacturer or product strings set, so
they wouldn't be detected.
Previously the USB communication code was split between api.ci,
dslogic.c and protocol.c, with protocol internals split between
both. This patch puts all the protocol handling code into one
source file reducing the number of internal interfaces and making
the code more readable.
Previously the USB communication code was split between api.c
and protocol.c, with protocol internals split between both. This
patch puts all the protocol handling code into one source file
reducing the number of internal interfaces and making the code
more readable.
When the processing of columns of text lines detected errors, the loop
was aborted and the routine was left, but allocated resources were not
freed. Fix the remaining memory leaks in the error code paths.
The constant at the top of the source file is the number of samples in a
datafeed submission chunk. The previous implementation erroneously made
it the size in bytes. There is no need to round down the buffer size
according to the unit size.
The previous implementation sent one sigrok session datafeed packet per
processed CSV line. This is rather inefficient for the CSV input module,
and triggers a dramatic performance loss in the srzip output format.
Communicate up to 128K samples within one datafeed packet. This fixes
bug #695.
Factor out repeated calculation of the unit size which is derived from
the channel count. Fix a minor memory leak in an error path while we are
here. (Other memory leaks in rare error paths remain with this commit.)
Suggested-By: Elias Oenal <sigrok@eliasoenal.com>
On the Windows platform it appears to be popular to _not_ terminate the
very last line in a text file. Which results in an unmet constraint in
the CSV input module and an internal exception in PulseView which aborts
program execution.
Cope with the absence of the text line termination sequence at the very
end of the input stream. Keep all other checks in place, such that only
completely received text lines get processed.
This fixes bug #635.
"Document" the current state of the implementation in the CSV input
module's source code. Discuss how text handling is non-trivial, which
approaches are available and how they have drawbacks.
Mention the lack of support for the import of analog data as well.
The CSV input module supports variable length end-of-line encodings
(either CRLF, or CR, or LF). When a bunch of accumulated text lines got
processed, do skip the corresponding number of characters after the end
of the last processed line.
This fixes one of the issues discussed in bug #635.
The input module runs receive() and end() invocations which end up
calling process_buffer(). It's perfectly legal to call the process
routine with an empty accumulation buffer, especially when the process
routine was called from end().
This fixes a condition where PulseView raised a fatal error at the end
of a completed successful import.
Reported-By: Sergey Alirzaev <zl29ah@gmail.com>
Move an independent test for single/multi column operation out of a code
path that checked for and then processed text lines. This commit does
not change behaviour, but prepares a subsequent commit.
Factor out a magic string literal which held a delimiter set yet could
be mistaken for an (assumed) fixed termination string. Concentrate the
determination of the end-of-line text encoding as well as the resulting
set of possible deliminters in one nearby location. The symbolic name
for the delimiter set eliminates the doubt on its purpose.
Handle the case when the sample data memory was filled and has wrapped
around during acquisition. Download the respective part of the data
which is reliably available, only skipping a single 1KB row which might
contain either old or new data while it's not certain which it would be.
This will be essential when triggers later become available. Right now
it copes with user requests for sample counts that exceed the total DRAM
capacity. Instead the maximum available amount of data is provided.
Of course acquisition no longer gets stopped when the end of DRAM is
reached.
Correctly determine the size of a download chunk for the last DRAM row
that's involved in the recent data acquisition.
This commit is based on work done by jry@.
This addresses bug #838 (trailing garbage).
It's assumed that the previously downloaded excess data was "swallowed"
by the sample count enforcement logic that was applied earlier, so the
(remainder of the) issue could have gone unnoticed, unless some other
termination condition than sample count was used.
Configure the samplerate clock and channel count during acquisition
start in identical ways for 50MHz, 100MHz, and 200MHz modes.
This part was inspired by work done by jry@ yet was addressed in
different ways (no exception, do everything in every mode the same way).
Eliminate a portability issue in the previous implementation. Make sure
to send the configuration bytes in the correct order to the hardware.
Don't typecase a struct reference to a bytepointer and hope that the
internal memory representation might fit the external hardware's idea.
Add a comment about sample memory organization in a central spot. This
concentrates knowledge which otherwise would be spread across several
locations all over the driver's codebase, yet is essential to have at
hand during maintenance.
All of the information was determined/updated by jry@ with the help of
Ondrej at Asix when he did lots of fixes and improvements to asix-sigma.
The Asix Sigma hardware does not support a sample count limit. Instead
this optional input parameter gets mapped to a sample time, and some
slack for hardware pipelines and compression gets added. When data
acquisition completes and sample data gets downloaded, chances are that
there is more data than requested by the user.
Do enforce the optional sample count limit. Stop sending data to the
sigrok session when the configured number of samples was sent.
This commit is based on work done by jry@.
This fixes bug #838.
Enhance how the data acquisition is stopped. Wait for the hardware to
flag the successful completion of data retrieval as well as flushing
through hardware pipelines.
Use symbolic identifiers for the mode register's fields (for read as
well as write access).
This commit uses part of a code update to better match the documentation
done by jry@, but not all of it to reduce the size of the commit.
Minor adjustment for improved readability. Don't hide assignments in
variable declarations. Move initialization of some variables closer to
related evaluation or subsequent processing. Break a complicated looking
roundup expression into several short steps.
Fix how the READ_ID register index was passed to the hardware access.
Addresses are sent in nibbles, so shift by eight is wrong here. No harm
was done, as the register's index is zero.
The Asix Sigma driver is aware of three firmware images, which are
required for acquisition with up to 50MHz, 100MHz, and 200MHz. The
previous implementation always downloaded the corresponding firmware
image whenever the sample rate has changed, which was redundant.
Skip the download when the new samplerate uses the same firmware as the
previously selected samplerate did. This results in faster responses in
the GUI when the samplerate selection changes.
Move assignments out of the variable declaration block for improved
readability while we are here.
The hardware provides captured data at a maximum rate of 16bits per 20ns
(50 MHz). For samplerates of 100 and 200 MHz one individual 16bit entity
contains multiple samples for a reduced number of channels. The bits of
several sample points are interleaved within the 16bit entity.
This commit is based on work done by jry@ who fixed a lot of issues with
the help from Ondrej at Asix.
This fixes bug #840.
Adjust the interpretation of acquired sample data such that regardless
of 50/100/200MHz samplerate the assignment of LA pins to sigrok channels
remains stable.
Introduce helper routines to access the sample data that is provided by
the ASIX hardware, as well as the buffer which accumulates logic data
before it gets sent to the session's datafeed.
This hides endianess issues from call sites, and prepares access to
memory layout which varies with sample frequencies.
This commit is based on work done by jry@.
This works around bug #359. Triggers currently are not operational for
Asix Sigma. Don't claim support in the driver so that UIs won't use the
feature. Yet allow research in this issue, by concentrating the switch
for the feature's support in a central location.
Add/update a comment and unobfuscate an error code path while we are here.
Both the .c and the .h file declared the same identifiers for USB
properties of ASIX hardware with identical values. Remove the .c
incarnation and keep the .h content, as the names are used in api.c
as well as protocol.c sources.
Introduce a separate routine which maps sample counts and sample period
to an elapsed sample time after which acquisition shall get stopped.
Add some more time to make sure the most recent captured data has passed
the hardware pipeline and is available for download.
This commit is based on work done by jry@.
When "tsdiff < EVENTS_PER_CLUSTER" we don't want "tsdiff - EVENTS_PER_CLUSTER"
(a negative number) to be treated as (int).
Submitted-By: jry <jrysig@gmail.com>
[ gsi: massaged for mainline submission ]
The resistance values of some DMMs were incorrectly reported due to a
missing factor of 10 in the calculations.
Tested on Voltcraft VC-920/VC-940 and Tenma 72-9380A/72-7730/72-7732.
Bump the number of supported logic channels from 8 to 128. This is
mostly motivated to test the 64 channels limit which some of the
components/subprojects of the sigrok project might have (input/output
modules, user interfaces).
Only automatically enable the first 8 of the 128 total logic channels,
i.e. default to the previous behaviour. Prepare to only enable part of
the set of analog channels, but stick with their being active by default
as well.
Factor out the choice for the default logic pattern, too. This allows
for easier adjustment of the default configuration, when settings are
concentrated in a single spot.
Extend the demo driver, add another waveform choice for logic channels.
Create a "cable squid" logo representation which occupies a large number
of channels.
This pattern occupies 128x128 pixels. Unlike the 'sigrok' pattern it
gets repeated when more channels are involved, but is not shifted in the
repetition.
Old:
ut71x: Applying exponent -12, new value is 0.000000.
P1: 1.500 nF AUTO
P1: 1.500 nF AUTO
New:
ut71x: Applying exponent -12, new value is 1.5e-09.
P1: 1.500 nF AUTO
P1: 1.500 nF AUTO
This fixes bug #700.
This is a (hopefully temporary) workaround for the
SR_CONF_CAPTUREFILE mechanism. The value for
vdev->capturefile is set by this, however only once
via stream_session_data().
During stream processing in stream_session_data(),
capturefile may receive new values - e.g. when there
are multiple logic files or if there is analog data.
With that, the initially set capturefile is overwritten.
When re-loading the file, we are then running into
issues because we don't know what the initial value was.
As all .sr files use "logic-1" by default and, we
simulate the behavior of stream_session_data() and
assign this name to capturefile if there are logic
channels present.
With this change, all three kinds of files reload
as expected: logic only, analog only and mixed signal.
For this reason, it's a short-term fix for #944.
The handling of the digital channels for this series is somewhere
between that of the DS1000D series (PROTOCOL_V2) and the MSO1000Z
(PROTOCOL_V4).
The :LA command set is similar to that of V4, but the LA data has to be
requested with :WAV:SOUR:LA and arrives in interleaved form like V2.
None of these changes should affect other models. They only affect the
case of PROTOCOL_V3 with digital channels, which occurs only for the
MSO2000A series.
'i' was iterating in steps of unitsize. However, the destination array
was also indexed with it, but it is of u8 type. Let 'i' run bytewise and
only multiply with unitsize when we need it.
This fixes parts of bug #844.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
'j' is the loop variable for channels, not 'i'.
This fixes parts of bug #844.
Reported-by: Maxim Sloyko <m.sloyko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
src/output/csv.c: In function 'dump_saved_values':
src/output/csv.c:461:6: warning: format '%lu' expects argument of
type 'long unsigned int', but argument 3 has type 'uint64_t' [-Wformat=]
ctx->sample_time, ctx->value);
^
Fixes#933.
We'd already had this problem elsewhere and thus have this wrapper function
that does this where necessary. It just wasn't in use on these two call sites,
which was causing timing problems when used over tcp-raw or VXI transports.
With trigger enabled, and with PulseView, a second (or more) acquisition
starts immediately instead of blocking. It's mandatory to try several times
to have a correct behavior.
According to http://mygizmos.org/ols/Logic-Sniffer-FPGA-Spec.pdf section 2.3.1
p.8, the Openbench Logic Sniffer must be reset before each arm command.
This fixes bug #809.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Openbench Logic Sniffer reset is a little more complex than a simple send.
To avoid code duplication, this patch adds a new function dedicated to
this task.
Signed-off-by: Gwenhael Goavec-Merou <gwenhael.goavec-merou@trabucayre.com>
Increasing the chunk size from 512ksamples to 4Msamples leads to
slightly faster session file loading from sigrok session (*.sr) files
in frontends, while not looking too "chunky".
The performance increase is not really massive, but still noticeable.
A further increase to, say, 10 or 100Msamples shows no further
noticeable improvements.
This changes the fx2lafw code to only enable the wide_sampling (16bit)
method, if at least one of the higher eight channels is enabled. This
has the benefit, that we can use higher samplerates on 16bit LA
devices if we use only the first eight channels.
The wide sampling is also enabled if we have one or more analog
channels.
Signed-off-by: Jan Losinski <losinski@wh2.tu-dresden.de>
I've seen the following output from sigrok-cli:
CH1: 478.720 mV
CH1: -514 mV
CH1: -0 V
I added some debug, and it seems like the digits value isn't reset
to the actual value after calling sr_analog_si_prefix_friendly():
using 6 digits
value2 0.478720 digits 6
value2 -0.513536 digits 3
value2 -0.487424 digits 0
This commit fixes this by resetting the value to the actual value before.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
devc->step is not reset on acquistion start, so acquisition
starts with a different value every time. Thats annoying when
using the demo driver to debug sigrok, so lets make sure that
it's reset to 0.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
When using SCPI over serial (over USB), we want the header without waiting
for the terminating newline, as otherwise the transfer may time out.
sr_scpi_get_data() will block until the message is complete.
Lowlevel access functions should not alter the data. sr_scpi_get_string(),
which is called by most highlevel access functions, strips newlines
in a central place, and is only fed with data which contains newlines
as a final terminator.
IEEE 488.2 definite length blocks may contain arbitrary data, thus the
payload up to the provided length should be passed unaltered.
Track if the last received character is a newline, which can be used
by sr_scpi_get_string() and its callers to determine if the response
is complete.
g_get_monotonic_time() returns current time in microseconds, use the same
granularity for storing the read timeout.
There is also no need to check the timeout if data has just been read.
sr_period_string takes the frequency as its argument, i.e. the reciprocal
of the timebase. Obviously this will not work for frequencies less than
1Hz / timebases greater than 1 second, but at least is correct for all
other available timebases.
sr_period_string takes the frequency as its argument, i.e. the reciprocal
of the timebase. Obviously this will not work for frequencies less than
1Hz / timebases greater than 1 second, but at least is correct for all
other available timebases.
The output was wrong for all frequencies but 1 Hz, 1 kHz, 1 MHz and 1 GHz.
With this changes, the output may still be off due to rounding, but will
be correct as to the shown accuracy.
When nothing was received in a read attempt, we need not adjust the
buffered data's read position nor the glib string object's size. Skip
any processing for empty input, just keep checking for timeouts.
Routine sr_scpi_get_data() checks for free space in the receive buffer,
and resizes the buffer when free space drops below a threshold. The
previous logic assumed that the resize and the read logic would interact
in some specific way to achieve the desired operation.
Adjust the buffer resize such that more free space is pre-allocated, yet
the payload size of the buffer is not affected. This eliminates the
dependency of the optional resize logic from subsequent activity for
reception of data that is non-optional.
Add comments while we are here, outline the steps taken in the
sr_scpi_get_data() routine.
Phrase the logic which checks the use of analog channels and digital
pods in more generic terms. Place a comment about the contraints' being
potentially dependent on the specific HMO model. This implementation
should lend itself better to future adjustment (HMO1002?).
An internal libsigrok implementation detail prevents partial submission
of logic data for different channel groups in multiple calls. Instead
one logic packet needs to be sent in a single call, which combines data
for all channels.
Introduce a logic data storage which folds samples from several channel
groups that were received at different points in time into a combined
memory layout of larger unitsize. Stick with the former shortcut of
passing on the input bytes directly when only the first digital pod is
used during acquisition.
This change correctly maps data from the second pod to channels D8-D15.
The previous implementation only added one of the digital channels to
the list of enabled channels that are involved in the acquisition (the
first one that was found). This means that when the set of used digital
channels spans more than one pod/group, the second pod will never be
read from.
Make sure to enable one digital channel per pod/group, such that
acquisition will retrieve data from all involved input sources.
Add comments while we are here. Mention how the different setup, check,
start, and receive routines which are spread across several files do
interact to achieve acquisition.
The previous implementation used to put FRAME_BEGIN and FRAME_END
markers around each received chunk of samples, while those chunks
correspond to a single channel (analog) or a group of eight channels
(digital) each. In other words, the hameg-hmo driver had provided a
multiple of the requested frames, and those frames were incomplete.
Make sure to only send FRAME_BEGIN before the first channel's data,
and FRAME_END after the last channel's data of a frame. Thus make
sigrok frames exactly match the scope's frames.
Add some comments on the frame marker and the acquisition stop logic
while we are here.
Configure the scope to the host's native endianess before downloading
acquisition data from analog channels. This unbreaks operation on those
models which default to a representation which differs from the host.
Undo the change which skips management activities when no data was
received. This change breaks the current implementation, and needs to
get deferred until a delicate interaction between the resize and the
read logic has been eliminated.
Replace a C library strcspn(3) call with the more portable glib
g_strstr_len(3) routine. This is possible since a single separator
is searched for, no actual "set of characters" is involved.
As a byproduct, this eliminates a "late" reference to 'cnt' at the
bottom of the routine, after the value was assigned in a rather distant
location at the top of the routine. The cost of strlen() should be
acceptable for a buffer with a single digit total length.
Replace C language string operations with their glib incarnations for
improved portability. Prefer a common sigrok float conversion routine
over a DIY implementation.
The specific packet layout puts constraints on the parse logic (case
sensitive comparison, order of comparison). Fix a comment that made no
sense before, and better reflect that there are two constraints.
Slightly rephrase the SCPI code which parses the responses that carry
(binary) data blocks. Be explicit about NUL termination when parsing the
leading length spec in the response, obsoleting the array initializer.
Add lots of comments and group source code lines to better reflect
what's happening from the protocol's perspective.
Fix the returned error code in the path which reads responses of
excessive length in chunks. The previous implementation detected errors
but always returned code 0 (success).
When nothing was received in a read attempt, we need not adjust the
buffered data's read position nor the glib string object's size. Skip
any processing for empty input, just keep checking for timeouts.
Drop an initial assignment to a variable which never takes effect.
Add braces around the body of a more complex if block. Separate routines
from each other by exactly one empty line.
When the channel state is retrieved, query the pre-set byteorder for
SCPI data blocks as well. When samples get retrieved during capture,
support float representations in either big or little endian format.
This commit unbreaks devices which operate in BE format by default
(tested with HMO2524). It keeps working with LE format as before. For
devices which don't support the byteorder query or return unknown
responses, LE format is assumed for backwards compatibility. The
device's byteorder is only queried and never set. This makes the
commit least intrusive.
A comment mentioned that the models HMO2524 and above support 16 digital
channels (and thus have two pods for the probes). Move those models to a
section that declares the respective features, including trigger support
on the upper digital channels.
Model detection and reflection of supported channels was tested on HMO2524.
Commit db81fbb582 made sure to release a potentially previously
allocated list of enabled channels before (re-)building the list in the
current invocation of acquisition start.
This commit frees the memory in the error path near the failed creation
already, which reduces the period of time where unused resources are
held, and eliminates a memory leak when acquisition is not stopped after
failed start.
Both approaches can coexist. Freeing an empty list is perfectly fine.
Fix the code which registers the name of the second pod for digital
probes. The previous implementation registered the first pod twice, and
lost the reference to the second pod. No harm was done, none of the
supported models declared support for two pods so far.
Factor out a channel to group mapping in the registration of digital
channels, while we are here.
The former DER EE DE-5000 driver was a very thin wrapper around the
ES51919 LCR meter chipset. None of its source was specific to the
deree-de5000 device. In fact it contained code for all currently
supported LCR meters, and it's expected that all LCR meters which
will get added in the future will fit in as well.
Follow the serial-dmm model. Rename the src/hardware/deree-de5000/
directory to serial-lcr/. Update the configure logic. Although the
source directory and the configure option are named serial-lcr, the
LCR meter still is used by specifying the "deree-de5000" device driver
(which just happens to reside in the serial-lcr driver sources, among
others).
Introduce an asycii.c source file (modelled after metex14.c) which
implements support for the 16-byte protocol of the ASYC-II multimeter
chipset (RX only, when the PRINT button was pressed).
Kumar Abhishek
Uwe Hermann
Stefan Brüns
Joel Holdsworth
Frank Stettner
Marcus Comstedt
turboaffe
Gerhard Sittig
Jan Luebbe
Soeren Apel
Richard
Angus Gratton
Martin Ling
Wolfram Sang
Johannes Römer
Gwenhael Goavec-Merou
Marc Schink
Bert Vermeulen
Jan Losinski
Sven Schnelle
Matthieu Guillaumin
Vlad Ivanov
Sebastian Tabares Amaya
Aurelien Jacobs
Vlad Ivanov
Karl Palsson